Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Elcomponent EnergyPro EP600i
Summary of Contents for Elcomponent EnergyPro EP600i
- Page 1 EnergyPro EP600i 6 channel Energy Analyser User's Guide...
- Page 2 All Rights Reserved. The information in this document is subject to change without notice. ELCOMPONENT has made every effort to ensure the accuracy of this manual. However, ELCOMPONENT makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability and fitness for a particular purpose.
-
Page 3: Table Of Contents
Table of contents Introduction ..................1 Safety ....................2 Firmware Feature ................3 Connection Check ............... 3 RMS Data Storage ............... 3 Power Calculations ..............3 Frequency ..................3 Energy Usage Display ..............3 Logger Connection ................4 Connection panel ................. 4 LED Indicators .................. -
Page 4: Introduction
EnergyPro Energy Analyser Introduction The EnergyPro represents leading edge technology in operator interfaces. Data can be viewed in real time on the front panel, or for more detail, PowerView software can be used to examine data collected by the EnergyPro. The EnergyPro: ▪... -
Page 5: Safety
EnergyPro Energy Analyser EnergyPro Energy Analyser Safety Firmware Features Although this instrument is designed to be as safe as possible, safety Connection Check is ultimately the responsibility of the operator. This instrument should Before a survey is started the user can set the voltage and current only be operated by suitably qualified and authorized personnel. -
Page 6: Energy Usage Display
EnergyPro Energy Analyser Red Logging LED Indicator This Red LED will flash when the logger is recording data. Firmware Features Green Charged LED indicator Energy Usage Display This Green LED will come on when the internal battery of the logger is The EnergyPro displays the total energy usage during the survey. -
Page 7: Turning On And Off
▪ In the middle section of the main screen, there are two status bars Display the hook-up configuration. displayed below the date and time field. The right status bar indicates memory used, and the left status bar indicates battery charge state. Below the memory status bar is the maximum survey duration in number of days. -
Page 8: Clock Setup
EnergyPro Energy Analyser EnergyPro Energy Analyser Logger Operation Logger Operation Clock Setup Clamp CT Setup The clock setup screen will appear when the clock icon on the main The CT setup screen will appear when the CT icon on the main screen screen has been selected. -
Page 9: Storage Rate Setup
30 Minutes 999 Days Memory card warning This graphic will appear if there is a write error or if a memory card not supported by the logger is inserted. EnergyPro Energy Analyser EnergyPro Energy Analyser Logger Operation Logger Operation Storage Rate Setup Voltage / Current / Power Factor Display The storage rate setup screen will appear when the filing... -
Page 10: Power Display
THD / Unbalance Display THD and Unbalance measurement are displayed by pressing F2 in the V&I screen. EnergyPro Energy Analyser EnergyPro Energy Analyser Logger Operation Logger Operation Hook-up Configurations Power Display The Power screen will appear when button is pressed. It displays real, apparent and reactive power for each phase. -
Page 11: 1P2W
Note 2. For direct connection in a delta system the 3P4W connection can be used with the neutral connection floating or connected to ground. Note 3. If the voltage and current inputs are connected to external CTs and PTs, then the external PTs must be connected A-B and C-B and the external CTs connected to A and C. -
Page 12: Start And Stop Logging
The EnergyPro starts recording on an even minute. While waiting for the recording to synchronize to the time the „running‟ icon will be animated to „run‟ on the spot. After the first record is recorded the „running‟ icon will be animated to move across the bottom of the screen and the red „logging‟... - Page 13 Battery Run Time 48 hours EnergyPro Energy Analyser EnergyPro Energy Analyser Specifications Specifications Measurement Environmental Specifications Comment Specifications Comment V1, V2, V3 Operating 0.5 % of full scale C to 60 0 - 600 VAC Temperature I1, I2, I3 Max 80% relative CT‟s are voltage Humidity 0 - 1V (Clamp)
-
Page 14: Notes
EnergyPro Energy Analyser Notes...
Need help?
Do you have a question about the EnergyPro EP600i and is the answer not in the manual?
Questions and answers