Subscribe to Our Youtube Channel
Related Manuals for Jet PS-1652T
Summary of Contents for Jet PS-1652T
- Page 1 Operating Instructions and Parts Manual 16ga. x 52-inch Pneumatic Shear Model PS-1652T 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-756203 Ph.: 800-274-6848 Revision C1 08/2018 www.jettools.com Copyright © 2015 JET...
-
Page 2: Important Safety Instructions
Do not use this machine for other than its 20. Use the right tool at the correct speed and intended use. If used for other purposes, JET feed rate. Do not force a tool or attachment to disclaims any real or implied warranty and do a job for which it was not designed. -
Page 3: About This Manual
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 4: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®... -
Page 5: Table Of Contents
8.4 Hold-down tension ............................ 10 8.5 Gibs ................................10 9.0 Maintenance ..............................11 10.0 Troubleshooting ............................11 11.0 Replacement Parts ............................. 11 11.1.1 PS-1652T Assembly – Exploded View ....................12 11.1.2 PS-1652T Assembly – Parts List ......................13 12.0 Electrical connections ..........................16... -
Page 6: General Features And Terminology
5.0 General Features and Terminology Numbers refer to corresponding index numbers in parts list. Figure 1 Table Rear Stop Cutter Bar Adjusting Block Hold Down Adjusting Block knobs Front Arm Extension Front Stop Spring Tension Adjusting Nuts Bevel Gauge Left Scale Filter Regulator Assembly Right Scale Rear Cover... -
Page 7: Specifications
Shipping weight, approximate ....................1344 lbs. (610 kg) The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 8: Set-Up And Assembly
7.0 Set-Up and Assembly 7.1 Hole center dimensions Figure 2 Place straps below the table (you may have to 7.2 Unpacking remove front cover), and use propery rated lifting equipment to move the machine to a Open shipping container and check for shipping level foundation. -
Page 9: Electrical Connections
7.4 Electrical connections 7.4.2 Extension cords The use of an extension cord is not recommended. Electrical connections must Try to place shop equipment within reach of the made qualified electrician power source. If an extension cord becomes compliance with all relevant codes. This necessary, make sure the cord rating is suitable for machine must be properly grounded to help the amperage listed on the machine’s motor plate. -
Page 10: Adjustments
8.0 Adjustments 8.1 Table and blades If the table requires adjustment, loosen four bolts (21); do not remove. Loosen nuts on the adjusting screws (18,19). The bed must rest squarely on the right and left hand side panels at all four corners while screws are loose. Shim legs at floor if necessary. -
Page 11: Maintenance
Number of your machine available when you call will allow us to serve you quickly and accurately. Some parts are shown for reference only, and may not be available individually. Non-proprietary parts, such as fasteners, can usually be found at local hardware stores, or may be ordered from JET. -
Page 12: Ps-1652T Assembly - Exploded View
11.1.1 PS-1652T Assembly – Exploded View... -
Page 13: Ps-1652T Assembly - Parts List
11.1.2 PS-1652T Assembly – Parts List Index No. Part No. Description Size 1 ....PS1652T-1G ..... Table ......................1 2 ....PS1652T-2G ..... Cutter Bar ...................... 1 3 ....PS1652T-3 ....Hold Down ..................... 1 4 ....PS1652T-4G ..... R.H. Side Panel ..................... 1 5 .... - Page 14 88 ....PS1652E-88 ....Rivet..............Ø2x6mm ........ 4 89 ....PS1652E-W ....Warning Label ....................1 90 ....PS1652E-J ....JET Plaque ....................1 91 ....PS1652E-S ....Specification Label ..................1 92 ....PS1652T-92 ....Bracket......................2 93 ....
- Page 15 145 .... TS-2284082 ....Phillips Pan Head Machine Screw ....M4x8 ........4 ....LM000164 ....ID Label, PS-1652T (not shown) ..............1 ....JET-203 ..... JET Logo (not shown) ........203 x 84mm ......1 NOTE: Non-proprietary fasteners (part numbers beginning with TS-) are standard sizes, and can usually be...
-
Page 16: Electrical Connections
12.0 Electrical connections L1 N1 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com...
Need help?
Do you have a question about the PS-1652T and is the answer not in the manual?
Questions and answers