System Settings; Gps And Glonass; Serial Interface Settings - Garmin GPSMAP 64sc SiteSurvey Owner's Manual

Odometer: A running tally of distance traveled for all
trips. This total does not clear when resetting the trip
data.
Off Course: The distance to the left or right by which
you have strayed from the original path of travel.
You must be navigating for this data to appear.
Pointer: An arrow points in the direction of the next
waypoint or turn. You must be navigating for this
data to appear.
Speed: The current rate of travel.
Speed Limit: The reported speed limit for the road. Not
available in all maps and in all areas. Always rely on
posted road signs for actual speed limits.
Speed - Maximum: The highest speed reached since the
last reset.
Speed - Moving Avg.: The average speed while moving
since the last reset.
Speed - Overall Avg.: The average speed while moving
and stopped since the last reset.
Stopwatch Timer: The stopwatch time for the current
activity.
Sunrise: The time of sunrise based on your GPS
position.
Sunset: The time of sunset based on your GPS position.
Temperature: The temperature of the air. Your body
temperature affects the temperature sensor. Your
device must be connected to a wireless temperature
sensor for this data to appear.
Temperature - Water: The temperature of the water.
Your device must be connected to a NMEA 0183
device capable of acquiring the water temperature.
Time of Day: The current time of day based on your
current location and time settings (format, time
zone, daylight saving time).
Time To Destination: The estimated time remaining
before you reach the destination. You must be
navigating for this data to appear.
Time To Next: The estimated time remaining before
you reach the next waypoint in the route. You must
be navigating for this data to appear.
To Course: The direction in which you must move to get
back on the route. You must be navigating for this
data to appear.
Total Lap: The stopwatch time for all the completed
laps.
Track Distance: The distance traveled for the current
track.
Trip Odometer: A running tally of the distance traveled
since the last reset.
Trip Time: A running tally of the total time spent
moving and not moving since the last reset.
Trip Time - Moving: A running tally of the time spent
moving since the last reset.
Trip Time - Stopped: A running tally of the time spent
14
not moving since the last reset.
Turn: The angle of difference (in degrees) between the
bearing to your destination and your current course.
L means turn left. R means turn right. You must be
navigating for this data to appear.
Velocity Made Good: The speed at which you are
closing on a destination along a route. You must be
navigating for this data to appear.
Vertical Dist to Dest: The elevation distance between
your current position and the final destination. You
must be navigating for this data to appear.
Vertical Speed: The rate of ascent or descent over time.
Vertical Speed To Dest: The rate of ascent or descent to
a predetermined altitude. You must be navigating
for this data to appear.
Waypoint At Dest: The last point on the route to the
destination. You must be navigating for this data to
appear.
Waypoint At Next: The next point on the route. You
must be navigating for this data to appear.

System Settings

Select Setup > System.
Satellite System: Sets the satellite system to GPS, GPS +
GLONASS, or Demo Mode (GPS off).
WAAS/EGNOS: Enables the system to use Wide Area
Augmentation System/European Geostationary
Navigation Overlay Service (WAAS/EGNOS) data.
Language: Sets the text language on the device.
NOTE: Changing the text language does not change
the language of user-entered data or map data, such
as street names.
Interface: Sets the format of the serial interface
Interface Settings, page 14)
AA Battery Type: Allows you to change the type of AA
battery you are using.
NOTE: This setting is disabled when the NiMH
battery pack is installed.

GPS and GLONASS

The default satellite system setting is GPS + GLONASS,
which offers increased performance in challenging
environments and faster position acquisition. Using GPS
and GLONASS can reduce battery life more quickly than
using GPS only.

Serial Interface Settings

Select Setup > System > Interface.
Garmin Spanner: Allows you to use the device USB port
with most NMEA 0183-compliant mapping programs
by creating a virtual serial port.
Garmin Serial: Sets the device to use a Garmin
proprietary format to exchange waypoint, route, and
track data with a computer.
NMEA In/Out: Sets the device to use standard NMEA
(Serial
.
GPSMAP 64sc SiteSurvey
®