Advertisement
Quick Links
IMPORTANT: The accuracy of the door preparation is
critical for the proper functioning and security of this lever
handle lock. Misalignment can cause premature wear and
tear and a lessening of security.
Tools Required
• 2-1/8" (54mm) hole saw
• 1" (26mm) boring bit
• 5/16" (8mm) drill bit
• 7/64" (2.5mm) drill bit
1. Mark door.
Mark horizontal line across edge of
door for centerline of lock at desired
installation height. Fold template over
edge of door, centering on horizontal
line. Mark centers of holes at proper
backset.
2. Drill door.
A. Drill 2-1/8" (54mm) dia. hole thru
the door. Cut notches as shown on
template. See note. (Except
Dummy Trim)
B. Drill 1" (26mm) dia. hole in edge of
door. Mortise for latch front 1-1/8"
(29mm) wide x 2-1/4" (57mm) high
x 5/32" (4mm) deep. (Except
Dummy Trim)
3. Install latch.
Insert latch in door. (Be sure bevel
edge of bolt faces strike plate.)
Attach with two screws supplied.
An ASSA ABLOY Group brand
5300LN Grade 2 or 4700LN Grade 1
Cylindrical Lever Locksets
Installation Instructions
• Chisel & hammer
• #2 phillips screw driver
• Handle removal tool (supplied)
• 3/8" or 1/2" drill
For beveled and square edge doors,
mark both sides of the door.
Note:
Be sure to verify backset before
marking & drilling door.
Note: To avoid splintering wood
doors, drill holes (A) and (C) from
both sides of the door.
4. Unpack lock.
Inside Lever
Handle
Attention Installer
Installation of cylindrical locks and latches must be through
bolted in all doors. If installation instructions are not followed this
may result in damage to the lock and void the factory warranty.
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
C. Drill two (2) 5/16" (8mm) dia.
holes thru door. See note.
D. Drill pilot holes for latch
screws. 7/64" (2.5mm) dia.
(Except Dummy Trim)
Outside Assembly
(stays assembled)
Through Bolts
D
B
Bushing
Inside Rose
Support Assembly
80-9150-0060-010 (11-16)
Door
Marker
Advertisement
Related Manuals for Yale 5300LN Grade 2
Summary of Contents for Yale 5300LN Grade 2
-
Page 1: Tools Required
Any retrofit or other field modification to a fire rated opening can Tools Required potentially impact the fire rating of the opening, and Yale Locks & Hardware makes no representations or warranties concerning • Chisel & hammer •... - Page 2 5. Adjust lock for door thickness (if necessary). (Lock is packed preadjusted for 1-3/4" (44mm) doors. Available for 2-1/4" (57mm) doors upon request.) 2-1/4" door To Adjust for Thicker Door A. Remove two (2) screws from outside rose. B. Slide outside rose away from lock body. C.
- Page 3 B. Slide cylinder into sleeve. C. Rotate key 45° counterclockwise. Depress retainer plate, push the handle onto the shank until fully seated. Pull on handle to ensure properly seated. Yale Cylinder Tailpiece Cylinder Sleeve (Note: Cylinder and Sleeve must be properly installed or the security of the lock will be compromised.)
- Page 4 Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2002, 2016, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9150-0060-010 (11-16)