Niigata seiki GDCP-200AA Instruction Manual

Hole Center Position
Digital Caliper
Thank you for purchasing Niigata Seiki Digital Hole Pitch Caliper.
This precision measuring tool measures distance between holes, or distance from hole center point to end face.
• For safe and proper use of this product, please read this instruction manual before use and follow the procedures described. Keep this
manual with the calipers for future reference.
• Keep this manual with the instrument if transferred or leased to a third party.
• For inquiries about this product, please contact dealer or Niigata Seiki at the address listed on the following page.
■
PARTS IDENTIFICATION・FUNCTION
GDCP-200TA
(For Hole Center to End Face Measurements)
②
Jaw
①
Measurement
Surfaces
① Measurement Surface ...... Surfaces which contact the workpiece.
② Jaw .............................. For positioning on object to be measured.
③ LCD Display .................. Displays digital measurement.
④ Lock Screw ..................
⑤ [HOLD] Button ............... When pressed, "HOLD" Icon appears on Display
⑥ Output Connector ......... Connect to optional Bluetooth Box to send

SAFETY PRECAUTIONS

Always follow these marked operating procedures in order to prevent harm to
yourself or others, and to prevent damage to property.
Denotes a prohibition ‒ You
MUST NOT do
WARNING Indicates risk of personal injury or property damage
if not followed.
Read this manual and follow the instructions.
・Use of product other than as described in the manual may cause accident.
Use only for measuring.
・Use for any purpose other than measuring may cause damage or wear to
the instrument. Improper use may also cause accident.
Handle with Care.
・Do not drop or subject instrument to excessive shock. Do not place under
heavy objects. Improper handling may cause damage or poor accuracy.
・Do not scratch instrument.
Avoid using in locations with high electric fields, such as near fluorescent
lights or switching power supplies.
・May cause damage to Display Unit or erroneous reading.
Use and store only in environment meeting the following conditions:
● Dry location protected from rain, water, and oils.
● Location that does not become hot.
● Location protected from use by children and unauthorized people.
・
Use in places contrary to the above may cause damage to the product resulting in
accident or injury.
Jaw Tips are Sharp—Handle With Care.
・Careless handling may cause injury.。
Do not disassemble or modify
・Doing so may cause accident or injury. Please contact distributor or place of
purchase for service.
Do not write on instrument with electric engraver.。
・Do not engrave instrument body or jaw arm, such as an ID number with
engraver or electric pen.
INSTRUCTION MANUAL
DIGITAL HOLE PITCH CALIPER
④Lock Screw
③ LCD Display
② Jaw
Tighten to prevent the slide and display from moving.
and measurement will be fixed.
measurements to PC.
Please Observe
Denotes a requirement ‒ You
MUST do
Model No.
⑤ [HOLD] Button
⑥ Output Connector
⑦ Battery Cover
⑧ [ZERO/INC] Button
⑨ [ON/OFF/P] Button
① Measurement
Surfaces
⑦ Battery Cover ............... Open to access battery.
⑧ [ZERO/INC] Button ......... When pressed, Display will read "0.00"
⑨ [ON/OFF/P] Button ......
⑩ Scale...........................
⑪ Reference Plate ............
PREPARATION FOR USE
Before using, please follow the steps below:
● Wipe off oil, rust proofing, and dirt from measuring surfaces
and slide. Contamination of surfaces may cause measurement
error.
● Allow the caliper and object to be measured time to reach the
same temperature.
A temperature difference between the object to be measured
and the caliper may cause measurement error. Allow enough
time for the temperatures to equilibrate.
PRODUCT SPECIFICATIONS
Model No.
GDCP - 200AA
GDCP - 200TA
• Resolution:
• Display:
• Auto Off:
• Maximum response speed:
(Left/Right as shown in
diagram at top of manual.)
• Operating Temperature Range: 0°C~40°C
• Storage Temperature Range:
• Power:
• Battery Life: approx. 2.5 years in normal use.
• Accessory:
GDCP-200AA / GDCP-200TA
⑩ Scale
GDCP-200AA
●
(For Hole Pitch Measurement)
⑪ Reference Plate
A B
For turning power ON / OFF, and for
Preset Function.
Supports LCD Display Unit.
For setting origin using the Preset
Function. Includes Inspection Report.
※Not including quantization error (±1 count)
Measurement Measured Hole
Range (mm) Diameter (mm)
20-200
φ1.5∼19.5
10-200
0.01mm
6 Digit LCD
approx. 20 min
Slide to Right ...... 1.5m/s
Slide to Left ...... 0.75m/s
－10°C~60°C
(1x) CR2032 Lithium Battery
・CR2032 Lithium Battery (1x, for test)
・Reference Plate
Instrument
Error (mm)
※
±0.05