Electrolux N7E Installation And Operating Manual page 25

• Metal objects can spoil or damage the steel: damaged
surfaces become dirty more easily and are more subject to
corrosion.
• Restore the satin finish if necessary.
SURFACES BLACKENED BY HEAT (when necessary)
• Exposure to high temperatures can cause the formation of
dark marks.
These do not constitute damage and can be removed by
following the instructions given in the previous section.
G G . . 1 1 . . 4 4 O O t t h h e e r r s s u u r r f f a a c c e e s s
Surfaces in mild steel or cast iron (daily)
• Remove dirt using a damp cloth or, in the event of
encrustations, the accessories (optional or supplied) speci-
fied in the list;
• After cleaning, switch the appliance on to dry the surface
quickly;
• Protect the surface with a light film of cooking oil.
NOTE!
Avoid dirtying the inside of the Venturi tubes. Dirt
inside the appliance can obstruct the nozzles,
affecting the flame.
G G . . 2 2 B B r r i i e e f f T T r r o o u u b b l l e e s s h h o o o o t t i i n n g g g g u u i i d d e e
All components requiring maintenance are accessible from the front of the appliance, after removing the control panel and front
panel.
W W A A R R N N I I N N G G
Disconnect the power supply before opening the appliance.
Malfunction
T T h h e e p p i i l l o o t t b b u u r r n n e e r r o o f f o o p p e e n n b b u u r r n n e e r r s s d d o o e e s s n n o o t t
l l i i g g h h t t
T T h h e e s s o o l l i i d d t t o o p p o o r r o o v v e e n n p p i i l l o o t t b b u u r r n n e e r r d d o o e e s s n n o o t t
l l i i g g h h t t
T T h h e e p p i i l l o o t t b b u u r r n n e e r r g g o o e e s s o o u u t t w w h h e e n n t t h h e e i i g g n n i i t t e e r r
k k n n o o b b i i s s r r e e l l e e a a s s e e d d
T T h h e e p p i i l l o o t t b b u u r r n n e e r r i i s s s s t t i i l l l l l l i i t t b b u u t t t t h h e e m m a a i i n n
b b u u r r n n e e r r d d o o e e s s n n o o t t l l i i g g h h t t
G G . . 1 1 . . 5 5
• Check the condition of the internal parts.
• Remove any deposits of dirt inside the appliance.
• Check and clean the discharge system.
G G . . 1 1 . . 6 6
If the appliance is not going to be used for some time, take the
following precautions:
• Close the valves or main switches ahead of the appliances;
• Go over all stainless steel surfaces vigorously with a cloth
moistened with paraffin oil in order to create a protective
film;
• Periodically air the premises;
• Have the appliance checked before using it again;
• For the electric heated models: switch the machine On at
the minimum rate of heat for at least 45 minutes; this will
allow moisture/humidity accumulated into the heating
elements to evaporate without damaging the elements.
Possible causes:
• Insufficient pressure in gas pipes;
• Nozzle blocked;
• Faulty gas valve;
• Igniter not properly fixed or connected;
• The ignition or the igniter cable are damaged;
• Insufficient pressure in gas pipes;
• Blocked nozzle;
• Faulty gas valve/tap.
• The pilot burner is not heating the thermocouple sufficiently;
• Faulty thermocouple;
• The gas valve knob is not being pressed enough;
• Lack of gas pressure at tap and/or valve;
• Faulty gas valve.
• Loss of pressure in gas supply pipe;
• Blocked nozzle or faulty gas tap or valve;
• Burner with gas outlet holes clogged.
I I M M P P O O R R T T A A N N T T
Do not use metal foil to protect the trays in
models with igniters without pilot flame.
I I n n t t e e r r n n a a l l p p a a r r t t s s ( ( e e v v e e r r y y y y e e a a r r ) )
I I M M P P O O R R T T A A N N T T
Operations to be carried out only by
specialised personnel.
I I M M P P O O R R T T A A N N T T
In particular conditions (e.g. intensive use
of the appliance, salty environment, etc.)
the above cleaning should be more
frequent.
I I d d l l e e p p e e r r i i o o d d s s
25