Electrolux N7E Installation And Operating Manual page 18

D D . . 3 3 O O p p e e r r a a t t o o r r q q u u a a l l i i f f i i e e d d f f o o r r n n o o r r m m a a l l m m a a c c h h i i n n e e u u s s e e
Must have at least:
• knowledge of the technology and specific experience in
operating the machine;
• adequate general basic education and technical knowledge
for reading and understanding the contents of the manual,
including correct interpretation of the drawings, signs and
pictograms;
E E I I N N S S T T A A L L L L A A T T I I O O N N A A N N D D A A S S S S E E M M B B L L Y Y
E E . . 1 1 I I n n t t r r o o d d u u c c t t i i o o n n
To ensure correct operation of the appliance and maintain safe
conditions during use, carefully follow the instructions given
below in this section.
C C A A U U T T I I O O N N
Before moving the appliance make sure
the load bearing capacity of the lifting
equipment used is suitable for its weight.
E E . . 2 2 C C u u s s t t o o m m e e r r ' ' s s r r e e s s p p o o n n s s i i b b i i l l i i t t i i e e s s
The tasks and works required of the Customer are:
• prearrange a high-sensitivity manual-reset magneto-ther-
mal circuit-breaker;
• prearrange a device lockable in the open position for the
connection to the power supply.
• check the floor planarity on which the machine is placed.
• install a rapid gas shutoff valve ahead of each individual
appliance (depending on the model). Install the valve in an
easily accessed place.
• for information regarding the electrical connection, refer to
E.9.1 Electrical appliances paragraph;
E E . . 3 3 D D i i s s p p o o s s a a l l o o f f p p a a c c k k i i n n g g
The packing must be disposed of in compliance with the
current regulations in the country where the appliance is used.
All the packing materials are environmentally friendly.
They can be safely kept, recycled or burned in an appropriate
waste incineration plant. Recyclable plastic parts are marked
as follows:
Polyethylene
• Outer wrapping
• Instructions bag
Polypropylene
• Straps
Polystyrene foam
• Corner protectors
E E . . 4 4 J J o o i i n n i i n n g g A A p p p p l l i i a a n n c c e e s s
1. Undo the 4 fixing screws and remove the control panels of
the appliances (Fig.1A);
2. Remove the fixing screw nearest the control panel, from
each side to be joined (Fig.1B);
3. Bring the appliances together and turn the feet to level
them until the tops match (Fig.1D);
18
• sufficient technical knowledge for safely performing his
duties as specified in the manual;
• knowledge of the regulations on work hygiene and safety.
In case of a significant anomaly (e. g. short circuits, wires
coming out of the terminal block, motor breakdowns, worn
electrical cable sheathing, etc.) the operator for normal
machine use must:
• immediately deactivate the machine and disconnect all the
supplies (electricity, gas, water).
4. Turn one of the two plates inside the appliances 180℃
(Fig.1C);
5. From inside the control panel of the same appliance, join
them at the front side, screwing one M5x40 Hex Head
screw (supplied) on the opposite insert (Fig.1E);
6. From the rear of the appliances, insert the coupling plate
(provided) in the side slots on the back panels;
7. Secure the plate with two flat head M5 screws provided
(Fig.1F).
1F
E E . . 4 4 . . 1 1 F F l l o o o o r r F F i i x x i i n n g g ( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e a a p p p p l l i i a a n n c c e e a a n n d d / / o o r r
m m o o d d e e l l ) )
To avoid accidental tipping of built-in half-module appliances
installed separately, fix them to the floor carefully following the
instructions enclosed with the corresponding accessory (1.0).
E E . . 4 4 . . 2 2 I I n n s s t t a a l l l l a a t t i i o o n n O O n n B B r r i i d d g g e e , , C C a a n n t t i i l l e e v v e e r r F F r r a a m m e e O O r r
C C e e m m e e n n t t P P l l i i n n t t h h ( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e a a p p p p l l i i a a n n c c e e a a n n d d / /
o o r r m m o o d d e e l l ) )
Carefully follow the instructions enclosed with the correspond-
ing accessory. Follow the instructions supplied with the
optional product chosen.
E E . . 4 4 . . 3 3 S S e e a a l l i i n n g g G G a a p p s s B B e e t t w w e e e e n n A A p p p p l l i i a a n n c c e e s s
Follow the instructions supplied with the optional sealing paste
pack.
1B
1C
1A
1E
1D