Maintenance; General; Cleaning; Replacing Display Light Bulbs (Gr2Bw Only) - Hatco GR2S-24 Operating Manual

MAINTENANCE

General

Hatco Glo-Ray Designer Heated Shelves and Buffet Warmers
®
are designed for maximum durability and performance, with
minimum maintenance.
WARNING
ELECTRIC SHOCK HAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before
adjustments, or maintenance.
• DO NOT submerge or saturate with water. unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at 800-558-
0607 or 414-671-6350; fax 800-690-2966; or International fax
414-671-3976.

Cleaning

To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Do not steam clean or use excessive water on unit.
This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
Submerging or saturating unit with water will damage unit
and void product warranty.
IMPORTANT — DO NOT use paper towel or glass cleaner to
clean plastic surfaces. Paper towel and glass cleaner may
scratch the material. Wipe off plastic surfaces using a soft,
clean, and damp cloth.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and wash all food pans.
3. Wipe down all exterior and interior surfaces using a non-
abrasive, damp cloth. a non-abrasive cleaner may be used
for difficult stains. Hard to reach areas should be cleaned
using small brush and mild soap.
4. For GR2BW models, clean the plastic sneeze guards and
side panels (if equipped) using a mild, soapy water solution
and a non-abrasive, damp cloth. NOTICE: DO NOT use
paper towel or glass cleaner.
5. Wipe dry the entire unit using a non-abrasive, dry cloth.
performing any cleaning,
Replacing Display Light Bulbs
(GR2BW Models only)
use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display lights are incandescent light bulbs that illuminate
the warming area. Each bulb has a special coating to guard
against injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant incandescent bulbs meet NSF
standards for food holding and display areas. For 100,
120, 120/208, and 120/240 volt applications, use Hatco
P/N 02.30.43.00. For 220, 240, 220–230, and 230–240
volt applications, use Hatco P/N 02.30.058.00.
NOTE: Shatter-resistant halogen bulbs are available in place of
the standard incandescent bulbs. For 100, 120,
120/208, and 120/240 volt applications, use Hatco P/N
02.30.081.00. For 220, 240, 220–230, and 230–240
volt applications, use Hatco P/N 02.30.082.00.
ELECTRIC SHOCK HAzARD: use only Genuine Hatco
Replacement Parts when service is required. Failure to use
Genuine Hatco Replacement Parts will void all warranties
and may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
aftermarket or generic replacement parts do not have the
characteristics that will allow them to operate safely in
Hatco equipment.
12
WARNING
WARNING
Form No. GR2S2BWm-0511