Table of Contents
Advertisement
Risk of injury!
v Unplug the mains plug of the Turbotrimmer prior to each
adjustment of the working position, to the shaft length,
additional handle or plant guard!
Connecting the trimmer [ Fig. O1 ]:
1. Insert the loop of the extension cable
from below through the handle
r
2. Plug the plug
of the trimmer into the socket
cable
q
.
3. Plug the extension cable into a 230 V mains power supply.
Setting the working position:
Working position 1 [ Fig. O2 ]:
For standard trimming.
Working position 2 [ Fig. O3 / O4 ]:
Trimming beneath obstacles.
1. Press the foot pedal
z
and lower the shaft downwards into the desired
working position.
z
2. Release the foot pedal
and allow the shaft to engage.
CAUTION! Avoid contact between the ground and the trimmer head in
working position 1 + 2.
Setting the trimmer to body height [ Fig. O5 ]:
Setting the shaft length:
v Loosen the clamping sleeve
i
shaft length and re-tighten the threaded collar
i
The clamping sleeve
must be fastened firmly enough to prevent the
shaft from being moved.
Setting the additional handle:
1
v Pull the lock
belonging to the additional handle
handle
2
to the desired incline and release the lock
If the trimmer is correctly set to the body height, the posture is upright
and the trimmer head in working position 1 is tilted forwards slightly.
v Hold the trimmer by the handle
a manner that the trimmer head is tilted forwards slightly.
Adjusting the plant guard [ Fig. O6 /O7 ]:
– Working position [ Fig. O6 ]
– Parking position [ Fig. O7 ]
v Turn plant guard
8
through 90° into the required position until it
locks into place.
Starting the trimmer [ Fig. O8 ]:
Switching the trimmer on:
v Press the start button
o
on the handle.
Switching the trimmer off:
o
v Release the start button
on the handle.
Filament feed (Tip mechanism) [ Fig. O9 / O10 ]:
The tip mechanism works when the motor is running. A clean cut is
only achieved with the maximum filament length. During first operation,
it may be necessary to extend the cutting filament several times.
1. Start the trimmer.
2. Hold the trimmer head
7
parallel to the ground and briefly touch the
7
trimmer head
onto a solid surface (avoid constant pressure over
extended periods of time).
p
The cutting filament
is automatically lengthened with an audible switch-
ing process and adjusted to the correct length with the filament limiter
If necessary tap several times one after the other.
4. STORAGE
To put into storage:
The product must be stored away from children.
v Store your Turbotrimmer in a dry place where it is protected from frost.
Recommendation:
The trimmer can be suspended by the handle. The trimmer head is not
placed upon any unnecessary strain if stored in a suspended manner.
8
q
into the cable strain relief
w
and pull tight.
t
of the extension
, extend the handle
w
to the desired
i
.
2
, set the additional
1
.
w
2
and additional handle
in such
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household waste.
It must be disposed of in line with local environmental regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
e
collection centre.
5. MAINTENANCE
DANGER! There is a risk of injury from the cutting filament!
v Always unplug the mains plug of the Turbotrimmer
before carrying out maintenance work!
Risk of injury and risk of damage to property!
v Never clean the trimmer with water or with a water jet
(in particular a high-pressure water jet).
Cleaning the trimmer [ Fig. M1 ]:
The ventilation slots must always be free of dirt.
v Clean all moving parts after each use, and especially remove any grass
and dirt from the cover
Replacing the filament cassette [ Fig. M2 / M3 ]:
Risk of injury!
v Never use metallic cutting elements or replacement
parts and accessories not provided by GARDENA.
Only use original GARDENA Filament Cassettes. You can order
Replacement Filament Cassettes from your GARDENA dealer or
directly from the GARDENA Customer Service.
• for Art. 9807 EasyCut 400/25:
GARDENA Filament Cassette for Turbotrimmers
1. Press in cassette cover
remove.
2. Remove the filament cassette
3. Remove any dirt.
4. Pull approximately 15 cm of the cutting filament
g
f ilament cassette
5. First thread the cutting filament
6. Thread the cutting filament
7. Insert the filament cassette
8. Fit the cassette cover
you hear both locking clips
When fitting the cassette cover
placed around the guide pin
v If the cassette cover
cassette
g
to and fro, until the filament cassette
the filament cassette holder
6. TROUBLESHOOTING
DANGER! Risk of injury from the cutting filament!
v Always unplug the mains plug of the Turbotrimmer
before troubleshooting.
Pulling the filament out of the filament cassette [ Fig. T1 ]:
a
.
If a filament is drawn into the filament cassette you can pull it out again as
described below.
1. Remove the filament cassette
"Replacing the filament cassette".
2. Press together the plastic ring
your thumb and forefinger.
3. Draw the plastic ring
(use a screwdriver if necessary).
You can now access the filament that was drawn into the filament
cassette.
4. Unwind the cutting filament
the eye of the plastic ring
beforehand using a screwdriver, and unwind and rewind completely.
0
and ventilation slots
s
.
d
f
on the two catches
at the same time and
g
.
p
out of the new
through the hole in the plastic ring
p
through the metal sleeve
p
k
around the guide pin
g
into the filament cassette holder
d
on the filament cassette holder
f
click into place.
d
p
, the cutting filament
k
and must not be trapped.
d
cannot be touched down, turn the filament
g
is completely in
l
.
g
as described under 5. MAINTENANCE
h
on the filament cassette
h
over the side part of the filament cassette
p
by approx. 15 cm and thread it through
h
. If necessary, loosen the welded filament
Art. 5307
h
.
j
.
.
l
.
l
so that
must be
g
between
Advertisement
Table of Contents
