Kit-Lock KL1000 Programming And Operating Manual

CODES - THE BASICS
• The KitLock has four code levels FUNCTIONS
available: Before programming, select the most
i) Master Code appropriate function for the application:
ii) Sub-Master Code A) or B) - See special Master Code
iii) User Code set up commands.
iv) Technician Code
• The KitLock is supplied with two A) PRIVATE USE
factory set codes: Important Note: This is the
Master Code: 11335577 default function and is already
User Code: 2244 pre-programmed in new locks.
• When fitted, immediately change This is the most common
the Master Code and User Code. function and is used where
• All Master Codes and Sub-Master the same code will be
Codes are 8 digits long. repeatedly used.
• All User Codes are 4 digits long.
• All Technician Codes are B) PUBLIC USE
6 digits long. The user enters their own personal
• The lock 'open' time is set four-digit code.
at 4 seconds.
This locks the lock. The same code
is entered once only to open the lock
before being erased and ready for the
next new user.
This function is used for short term,
multi occupancy applications,
e.g. a locker in a leisure centre.
OPERATING INSTRUCTIONS
Note: The KitLock has a 10 button Blue LED = Code accepted
keypad and a # button.
The # button is hidden beneath the Red LED = Code rejected
handle when in the locked position.
CODES The lock has the following code levels:
MASTER CODE TECHNICIAN CODE
The Master Code can: The Technician Code can:
• Open the lock
• Open the lock
A code cannot be programmed into more
• Change the Master Code
than one level.
• Set / Change / Delete the Sub-Master
and User Code
LOST CODE PROCEDURE
• Select between Private and
Note: The procedure requires the door to
Public Functions
be open
• Activate/deactivate Technician Code
• Remove the rear-fixing bolt and
swing the lock over the edge of the
SUB-MASTER CODE
door to reveal the battery
The Sub-Master Code can:
compartment.
• Open the lock
• Remove one battery.
• Change the Sub-Master
• Press and hold the 1 button, replace
• Set / Change / Delete / the User Code
the battery, the Blue LED will flash
twice, release the 1 button. Within
USER CODE
three seconds press the 1 button
The User Code can:
three times. The Blue LED will flash
• Open the lock
twice and the lock will have reverted
• Change the User Code
to the factory Master Code 11335577
and all other stored settings will be
erased.
PENALTY TIME BATTERY FAILURE OVERRIDE
• Entering three incorrect codes will The KitLock has been designed so an
cause the lock to shutdown for 10 external PP3 battery can be placed against
seconds. the contact points surrounding the Blue
and Red LED's so the lock can be opened
BATTERY POWER to replace the batteries should they fail.
• The KitLock should provide well in
excess of 15,000 openings, of 4 The procedure is as follows:
seconds each, from 2 x AAA 1.5v cells. • Place the contact points of the PP3
battery against the contact points
surrounding the Blue and Red LED's.
LOW BATTERY
• When the battery power is low the • The positive + PP3 terminal against the
•
Red LED will flash 3 times before Red LED contact point and the negative
•
the Blue LED lights, accepting the – PP3 terminal against the Blue LED.
code. Fit new batteries as soon as this • Enter the Master Code.
happens. The lock will operate for 100 • The motor will withdraw the locking pin
times with low battery. allowing the lock to be opened.
• Fit new batteries by removing the
Code rejected upper fixing bolt and swinging the lock
Low battery indicator down over the edge of the door. Refit
the lock.
Code accepted
PROGRAMMING
To program – the lock must be in the
open position with the # button visible.
Every program command must commence
by pressing the # button, followed by
either the Master Code, Sub-Master Code
or User Code.
OPEN LOCKED
KL1000 can be supplied
vertically, left or right
hand horizontal.