Kit-Lock KL1500 Programming & Operating Instructions

CODES - THE BASICS OPERATING INSTRUCTIONS
The KL1500 has a 12 button keypad.
• The KL1500 has four code levels FUNCTIONS
The # button is used as a prefix when
available: Before programming, select the most
programming for all code levels.
i) Master Code appropriate function for the application.
The KL1500 standard unit is installed in the
ii) Sub-Master Code
vertical (up) position with the lever at the
iii) User Code A) PRIVATE USE
bottom. However, the lock may be installed
iv) Technician Code Important Note:
in any of 4 positions; up, down, horizontal
• The KL1500 is supplied with two This is the default function
(left or right). Should the lock need to be
factory set codes: pre-programmed in new locks.
changed from one position to another

Master Code: 11 22 33 44

please see Installation Instructions.

User Code: 12 34

This is the most common function
• Before fitting, change the Master and is used where the same code
PROGRAMMING CODES
Code and User Code. will be repeatedly used.
• All Master Codes and Sub-Master
The programming functions
Codes are 8 digits long. B) PUBLIC USE
• All User Codes are 4 digits long. The user enters their own personal code of the code levels are:
• Up to 20 individual User Codes twice, the second time to confirm the
MASTER CODE
can be entered into the lock correct code. This locks the lock.
The Master Code can:
at the same time. Each User Code To open the same code is entered once
• Open the lock.
is entered together with specific ID again and then will be erased.

• Change the Master Code.

(Identification Number) from 01-20. The lock will remain open until a new
• Set Public Use or Private Use Function.
• All Technician Codes are code is entered.
• Set, change or delete the Sub-Master Code.
6 digits long. This function is used for short term,
• Set, change, suspend or restore User Codes.
• The lock 'open' time is set multi occupancy applications eg:
• Set or delete Technician Code.
at 4 seconds. a locker in a leisure centre or Spa.
• Set or cancel Dual Code mode.
• Set or cancel hours locked time.
• Set 24hr clock.
• Set or cancel Auto-Open Time.
• Set lock status indicator.
• Disable or enable sounder.

SUB-MASTER CODE

LOST MASTER CODE PROCEDURE

PENALTY TIME
• Remove BOTH coin cell batteries. • Entering three incorrect codes will
The Sub-Master Code can:
• Press and hold the 0 button. cause the lock to shut down for 10
• Open the lock.
• Change the Sub-Master Code. • Replace one battery, Blue LED will seconds.
flash twice.
• Set, change, suspend or restore
• Release the 0 button and within three BATTERY POWER
User Codes.
seconds press the 0 button 3 times. • The KL1500 should provide in excess
• Set lock status indicator.
• Blue LED will flash twice and the of 50,000 openings of 4 seconds
• Disable or enable sounder.
lock will revert back to last active each from 2 x CR2450 3.0 V coin cell
mode – Public Use or Private Use batteries.
USER CODE
Function and the Master Code
The User Code can:
will now be the factory default e.g. LOW BATTERY
• Open the lock.
11223344. • When battery power is low the Red
• Change the User Code.
Note: All previously programmed LED will flash 3 times before the Blue
codes and settings will be RETAINED. LED light accepting the code. Fit new

TECHNICIAN CODE

• Replace second battery. batteries as soon as this happens.
The Technician Code can:
Note: To retain Program 15 Time
• Open the lock in Public Use

FACTORY CODE RESET

Setting, one battery must be changed
Function without erasing the
Reset lock to factory supplied settings: at a time.
User Code. • Remove both batteries.
• Press and hold the 1 button and replace
The same code can be used in one
one battery.
level only.
• The blue LED will flash twice and
beep twice.
• Release the 1 button and within 3 seconds
*
press the button 3 times.
• The blue LED will flash and beep twice to
confirm factory reset.
• Refit second battery.
Note: Lock will revert to Master Code of
11223344 and User Code 1234.
All previously entered settings and codes
will have been ERASED.
BATTERY OVERRIDE
Should the batteries fail the lock can be
opened using the code and an external
PP3 battery as the power source as
follows:
The procedure is as follows:
• Place the +positive contact
of the battery against the contact
point surrounding the Red LED and
the –negative contact point of the
battery against the contact point of the
Blue LED.
• Enter Master Code.
• Lock will open.
• Remove the lock and replace batteries.
• Refit lock.
•
Code rejected
low battery indication
•
Code accepted
Blue LED = Code accepted
Red LED = Code rejected
CHANGE THE MASTER CODE RESTORE INDIVIDUAL USER CODE (PRIVATE USE FUNCTION ONLY)
• • • ••
#Master Code 01 New Master Code New Master Code #Master Code
• • • ••
Example: #11223344 01 22334455 22334455 Example: #11223344
Result: Master Code has been changed to 22334455. Result: User Code ID number 01 restored.

SELECT PRIVATE USE OR PUBLIC USE FUNCTION

SUSPEND ALL USER CODES (PRIVATE USE FUNCTION ONLY)
• • • ••
#Master Code 02 #### **** #Master Code
• • • ••
Example: #11223344 02 #### **** Example: #11223344
Result: If lock was set in A) Private Use it will now work in B) Public Use. Result: All User Codes suspended. Red and Blue LED will signal together after
If lock was in B) Public Use it will now work in A) Private Use. every valid code is entered and lock will remain locked.
Note:
• Factory default is A) Private Use. RESTORE ALL USER CODES (PRIVATE USE FUNCTION ONLY)
• In B) Public Use the Red LED is factory set to flash every 3 seconds when #Master Code
locked, unless overridden by Program 19. Example: #11223344
Result: All User Codes restored.

SET OR CHANGE THE USER CODE (PRIVATE USE FUNCTION ONLY)

• • • ••
#Master Code 03 User Code ID User Code

SET OR CHANGE THE SUB-MASTER CODE

• • • ••
Example: #11223344 03 02 1455 #Master Code
Result: New User Code 1455 now valid in position 02. Example: #11223344
Result: Sub-Master Code 55667788 now valid.
SUSPEND INDIVIDUAL USER CODE (PRIVATE USE FUNCTION ONLY)
• • ••
#Master Code 04 User Code ID

DELETE THE SUB-MASTER CODE

• • ••
04 01 #Master Code
Example: #11223344
Result: User Code ID number 01 valid but suspended. This will be identified Example: #11223344
by the Red and Blue LED signalling together after the code has been entered. Result: The Sub-Master Code is deleted.
Lock will remain locked.
• • ••
05 User Code ID
• • •
05 01
• ••
06
• ••
06
• ••
07
• ••
07
• • • ••
08 Sub-Master Code Sub-Master Code
• • • ••
08 55667788 55667788
• • ••
09 09
• • ••
09 09