Kit-Lock KL1000 Programming & Operating Instructions

CODES - THE BASICS
• The KitLock has five code levels FUNCTIONS
available: Before programming, select the
i) Master Code most appropriate function for the
ii) Sub-Master Code application:
iii) User Code A), B) or C) – See Special
iv) Technician Code Master Code set up
v) NetCode
commands.
• The KitLock is supplied with two
factory set codes: A) PRIVATE USE
Master Code: 11 33 55 77 Important Note: This is
www.kitlock.com
User Code: 22 44 the default function and is
sales@kitlock.co.uk
• Before fitting change the Master already pre-programmed in
sales@kitlock.us
Code and User Code. new locks. This is the most
KitLock is a Codelocks Limited Brand • All Master Codes and Sub-Master
common function and is used
Codes are 8 digits long.
CODELOCKS LTD UK where the same code will be
Tel: +44 (0) 1635 239645
• All User Codes are 4 digits long. repeatedly used.
Fax: +44 (0) 1635 239644
• All Technician Codes are
sales@codelocks.co.uk
6 digits long. B) PUBLIC USE
Helpline, service & spares
FREEPHONE 0800 393 405
• All NetCodes are 12 digits long. The user enters their own personal
• The lock 'open' time is set four-digit code twice, the second
CODELOCKS INC US
Tel: +1 714 979 2900 at 4 seconds. time to confirm the correct code.
Fax: +1 714 979 2902
This locks the lock. The same
sales@codelocks.us
code is entered once only to open
Help: 1.877.CODELOCK
www.codelocks.com the lock before being erased and
ready for the next new user. This
function is used for short term,
multi occupancy applications,
e.g. a locker in a leisure centre.
OPERATING INSTRUCTIONS
Note: The KitLock has a 10 button
C) NETCODE
keypad and a # button.
The NetCode function enables
The # button is hidden beneath the
the lock owner to generate time
sensitive codes for locks installed handle when in the locked position.
remotely. NetCode function is
activated prior to shipping to CODES The lock has the following code levels:
remote site/installation via web
based application. This function is
MASTER CODE
typically used for issuing codes to
The Master Code can:
visiting service engineers, delivery
• Open the lock.
personnel (drop boxes), medium
• Change the Master Code.
term locker rental. Generated
• Set / Change / Delete the Sub-Master
codes can be sent by email or
and User Code.
SMS to any email account or
• Select between Private and
mobile phone via a password
Public Functions.
protected kitlock.net account.
• Activate/deactivate Technician Code.
• Activate NetCode.
SUB-MASTER CODE
The Sub-Master Code can:
• Open the lock.
• Change the Sub-Master.
• Set / Change / Delete / the User Code.
USER CODE
The User Code can:
• Open the lock.
• Change the User Code.
Blue LED = Code accepted
LOST CODE PROCEDURE
Note: The procedure requires the
Red LED = Code rejected door to be open:
• Remove the rear-fixing bolt and
swing the lock over the edge of the
door to reveal the battery compartment.
• Remove one battery.
• Press and hold the 1 button, replace
TECHNICIAN CODE
the battery, the Blue LED will flash
The Technician Code can:
twice, release the 1 button. Within
• Open the lock.
three seconds press the 1 button
three times. The Blue LED will flash
NETCODE
twice and the lock will have reverted
The NetCode can:
to the factory Master Code 11 33 55 77
• Open the lock for a particular date,
and all other stored settings will
time and duration.
be erased.
A code cannot be programmed
into more than one level.
PENALTY TIME BATTERY FAILURE OVERRIDE
• Entering three incorrect codes The KitLock has been designed so an
will cause the lock to shutdown external PP3 battery can be placed against
for 10 seconds. the contact points surrounding the Blue
and Red LEDs so the lock can be opened
BATTERY POWER to replace the batteries should they fail.
• The KitLock should provide well
in excess of 15,000 openings, of 4 The procedure is as follows:
seconds each, from 2 x AAA 1.5v cells. • Place the contact points of the PP3
battery against the contact points
LOW BATTERY surrounding the Blue and Red LEDs.
• When the battery power is low the • The positive + PP3 terminal against
•
Red LED will flash 3 times before the Red LED contact point and the
•
the Blue LED lights, accepting the negative – PP3 terminal against the
code. Fit new batteries as soon as this Blue LED.
happens. The lock will operate for 100 • Enter the Master Code.
times with low battery. • The motor will withdraw the locking pin
allowing the lock to be opened.
•
Code rejected
• Fit new batteries by removing the
low battery indication
upper fixing bolt and swinging the lock
•
down over the edge of the door.
Code accepted
Refit the lock.
PROGRAMMING
To program – the lock must be in
the open position with the # button
visible. Every program command must
commence by pressing the # button,
followed by either the Master Code,
Sub-Master Code or User Code.
NC
Programming
& Operating
Instructions
for Netcode