Table of Contents
Related Manuals for Laguna Tools REVO 1216
Summary of Contents for Laguna Tools REVO 1216
- Page 1 REVO 1216 Lathe Owner's Manual MLAREVO1216EVS 2072 Alton Parkway Irvine, CA 92606 U.S.A. Service: +1 (949) 474-1200 or email customerservice@lagunatools.com Ultimate Woodturning EVS Midi Lathe REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018 10/22/2018...
-
Page 2: Table Of Contents
No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. REVO 1216 Lathe ©2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 10/22/2018... -
Page 3: Safety
20. SENS D'ALIMENTATION. Alimentez la pièce vers la lame ou le couteau dans le sens contraire de sa rota on seulement. 21. NE LAISSEZ JAMAIS UN OUTIL FONCTIONNER DANS SURVEILLANCE – ÉTEIGNEZ L'OUTIL. Ne laissez pas l'ou l sans surveillance jusqu'à ce qu'il s'arrête complètement. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... - Page 4 Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018...
-
Page 5: Warranty
The owner's responsibility includes this warranty unless otherwise stated by Laguna Tools. These parts are designed to be used at the expense of the operator and are available for replacement or inventory purchase. The determination of a consumable part will but is not limited to the proper installation of the product in a safe environ ment, be made on a case-by-case basis by Laguna Tools. -
Page 6: Reference
You set the speed and go to work. In addition, many of Overall Size L29.4" W8.9" H17.4" L60" W26" H52.25 the features from the 18 and 24 were brought down to the 12|16; the reverse REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... - Page 7 No part of this publication may be reproduced, transmitted, or translated into any language in any form Tool Rest Contact Rod 6mm (DIA) Hardened 1045 Steel by any means without our written permission. Errors and omissions may be current. Banjo Iron 1.1.6 Features REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018...
-
Page 8: Dimensions
1. Reference 1.2 Dimensions Stand Floor Space (with mobility kit) Stand Floor Space Capacities (with extension accessory) REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 9: External Map
Clockwise to go in, counterclockwise to come out. Come all the way out to pop out Wheel (Quill) the (self ejecting) live center. Figure L001: REVO 1216 Lathe external map feature image. Center Storage Stores your stuff. (1) Control Panel. (2) Head-stock. (3) Power Inverter(*note). (4) Spindle Lock. (5) Holds the workpiece in in line with the spindle. -
Page 10: Internal Map
50 - 525 RPM 1.5 Control & Display Elements Fig L002 - REVO 1216 Control Panel. Figure L003B: REVO 1216 Lathe internal map feature image. (1) On button (Power). (2) Off button. (1) Front Spindle Threading - 1"x 8 TPI. (2) Head-stock Front Bearing - 6006LLU. (3) (3) Speed adjustment knob - CW to Spring Loaded Spindle Lock. -
Page 11: Setup
Parts Section The machine comes as assembled as possible without impacting shipping costs. Fig L008: Receiving and un-boxing the REVO 1216 Lathe. (1) Un-boxing Contents. (2) Lathe With this, there will always be some setup procedures and adjustments that the in box. -
Page 12: Inventory
Used in the tail-stock to keep workpiece rotating. Has a bearing. PLAREVO1216-168 4x Rubber Foot Rubber feet to limit vibrations - Remove if using stand. PLAREVO1216-199 4x Caster Screw PLAREVO1216-1100 4 x Flat Washer PLAREVO1216-198 REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 13: Functional Setup
2. Completely loosen the (2) quill (plunge) by turning the handle counter clockwise. to install, if you over-tighten, the set screw flats (on spindle) may not line up and you could damage the threading. Hand tightening is usually sufficient. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 14: Changing Between Speed Groups (Pulley Steps)
CAUTION! The workpiece must be balanced. If unbalance, the lathe may vibrate too heavily and cause problems. Especially with "live edge" pieces, remove any large REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 15: Accessories & Options
Q: Can i order only the 10" Extension piece? A: No Fig L004: 10" Outboard Extension for REVO 1216 10". Includes 10" Extension, Outboard turning tool rest knuckle, and Tool Rest clamp. (1) As bed lengthening function - increased center to center from 15" to 25". (2) As outboard turning function - allows for 16" throwing capacity. - Page 16 As Bed Extension: 3. The bolt holes on the REVO 1216 bed are pre-tapped to accept the extension. Using the three (2.3) Allen screws, fasten the extension to the right side (of the bed) extension mounts.
-
Page 17: 1216 Stand
1. Never accept a shipment that is damaged or partial without notifying the shipping company and the purchasing store. Fig L005: Stand for REVO 1216 10". Includes adjustable lathe stand and tool rack. (1) In lowest 29.6" (floor to spindle center-line) position. (2) In Highest 29.6" position. (3) Tool Un-boxing Rack - holds faceplate, both centers, knock out rod, 9 chisel tools with 1"... - Page 18 Main contact point from lath to stand. Allows for adjustable height. lathe out of the stand when adjusting height later on. PLAREVO1216-204 8. Using an additional person, place the REVO 1216 Lathe onto the assemble Sheet Steel constructed stand leg. Has pre-tapped holes to mount (2) machine Stand Leg stand.
-
Page 19: Deluxe Wheel System
Support Plate Mounts to the (inside) stand leg with (2.2) foot pedal assembly. Foot Pedal Caster Mounts to (2.2) foot pedal assembly. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 20: Machine Light
11. When the foot pedal is in the raised position, the (2.4) foot pedal wheel should be approximately 1/2" to 1" above the rubber casters on the bottom of the stand leg. With this criteria met, fasten down all four bolts. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 21: Maintenance Work
9. Now you can replace the belt or bearings. 10. To reassemble reverse the procedure. NOTE: When reinstalling clamping nut thread it on to the spindle until its snug. Then back off slightly and tighten the socket head cap screw. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 22: Troubleshooting
4. Drive belt loose. Re-tension drive belt. Machine vibrates. 1. Machine not level on the floor. Re-level the machine ensuring that it has no movement. 2. Damaged drive belt. Replace the belt. REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 23: A1. Wiring
Customer Support: (949)-474-1200 or customerservice@lagunatools.com Option: Mobility (MBA14/12 WHEEL SYSTEM) Option: Extension (ALAREVO12 EXTENSION) Revo 1216 Banjo, Tool Rest, Tail Stock, Centers Figure LW01 - REVO 1216 (MLAREVO1216EVS) Wiring Diagram. 110V/1PH/60HZ Power REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 24: Revo 1216 Headstock Assembly
PLAREVO1216-1104 Knob PLAREVO1216-111 Headstock PLAREVO1836-181 Knob PLAREVO1216-112 Poly-V Belt PJ6-290 PLAREVO1836-1136 Handle, Faceplate PLAREVO1216-113 Spindle Pulley PLAREVO1836-184 Wave Washer 6205 PLAREVO1216-115 Ball Bearing 6005LLU PLAREVO1836-1119 Set Screw 1/4-20UNCx3/8 PLAREVO1216-117 Handwheel PLAREVO1216-118 INDEX-PIN REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 25: Revo 1216 Bed, Internals, Motor
M3x8 PLAREVO1216-144 Lower Door PLAREVO1216-145 PLAREVO1216-146 Link block PLAREVO1216-147 Belt Tension Handle PLAREVO1216-148 Belt Tension Base PLAREVO1216-149 PLAREVO1216-150 Spring PLAREVO1216-151 Belt Tension Shaft PLAREVO1836-1113 Flat Washer D8xD18x2t PLAREVO1216-153 Nylon Insert Lock Nut REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 26: Option: Stand (Alarevo12 Stand)
Stand PLAREVO1216-1101 Cord Holder PLAREVO1216-202 Stand PLAREVO1216-1108 Power Cord PLAREVO1216-203 Connect Plate PLAREVO1216-1109 Control Cord PLAREVO1216-204 Adjust Set PLAREVO1216-205 Rubber Bushing PLAREVO1216-206 Rubber Bushing PLAREVO1216-207 Rubber Bushing PLAREVO1216-208 Hex Cap Screw 5/16-18UNCx1/2" REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 27: Option: Mobility (Mba14/12 Wheel System)
Wheel Bracket PBAND1412-175-6-9 DU Bearing MB1620DU PBAND1412-175-6-10 Spring PBAND1412-175-6-11 Caster PBAND1412-175-6-12 Spacer PBAND1412-175-6-13 Flat Washer PBAND1412-175-6-14 Screw M5x0.8x20 PBAND1412-175-6-15 Connecting Plate PBAND1412-175-6-16 Foot Pedal PBAND1412-175-6-17 Socket Head Button Screw 1/4"-20x3/8" PBAND1412-175-6-18 Plate REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... -
Page 28: Option: Extension (Alarevo12 Extension)
Socket Head Button Screw 5/16"-18x3/4" PBAND1412-175-6-28 Knob PBAND1412-175-6-29 Support Plate PBAND1412-175-6-30 Hex Cap Screw M8x1.25x70 Part Number Description Specification PLAREVO1216-301 Extension Bed PLAREVO1216-302 Toolrest Extension PLAREVO1216-164 Lock Handle PLAREVO1836-303 Socket Head Button Screw 3/8-16UNCx1" REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018... - Page 29 Stand Floor Space (with mobility kit) Legs or Base 10, 22 - R - Starter Switch Length of Waranty Dust Collection Steel Bed LIGHT Rear Bearing Dust Port Outer Diameter Swing Over Banjo REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018...
- Page 30 Tool Rest Post Dia. Tool Storage Troubleshooting - U - Un-boxing Upper Belt Door - V - vibrate Viewing Window - W - warranty Warranty Limitations Wheel System 19, 27 Wiring Work REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018...
- Page 31 No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. REVO 1216 Lathe ©2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 10/22/2018...
- Page 32 Lagunatools.com 2072 Alton Parkway Irvine, CA 92606 U.S.A. For Customer Service: +1 (949) 474-1200 or email customerservice@lagunatools.com REVO 1216 Lathe © 2018 Laguna Tools 10/22/2018...