Table of Contents
Advertisement
Section 3: Operating Instructions
Section 3: Operating Instructions
Startup Checklist
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Rotary Cutter. It is absolutely
essential that no one operates the cutter unless they are
age 16 or older and have read, fully understood, and are
totally familiar with the Operator's Manual. Make sure the
operator has paid particular attention to:
Important Safety Information, page 1
•
Section 1: Assembly & Set-up, page 13
•
Section 2: Adjustments, page 28
•
Section 3: Operating Instructions, page 30
•
Section 4: Options & Accessories, page 37
•
Section 5: Maintenance & Lubrication, page 39
Perform the following inspections before using your
Rotary Cutter.
Operating Checklist
Check
Make sure all guards and shields are in place
and in good working condition.
Refer to "Important Safety Information" .
Follow hook-up and driveline installation
instructions.
Refer to "Section 1: Assembly & Set-up".
Make all required adjustments.
Refer to "Section 2: Adjustments".
Preform all required maintenance.
Refer to "Section 5: Maintenance & Lubrication".
Lubricate cutter and drivelines as needed.
Refer to "Lubrication Points".
Lubricate all gearboxes and replace oil plugs
properly. Refer to Gearbox lubrication.
Check cutter initially and periodically for loose
bolts and pins. Refer to "Torque Values Chart" .
Safety Information
!
DANGER
To avoid serious injury or death:
•
Do not walk, stand, or allow anyone else in the area where
a raised wing will fall unless the wing is securely locked in
the raised position with its transport lock.
•
Rotary Cutters have the ability to discharge objects at high
speeds; therefore, the use of front and rear safety guards are
required with this cutter. Specifically, double row chain
guards should be used when cutting along roadways and in
areas where people may be present. Stop blade rotation if
bystanders are in or around the area.
•
Tractor power take-off shaft shield, driveline shields, and
gearbox shaft shields must be installed and in good working
condition to avoid driveline entanglement and projectiles
flying off of the driveline.
30
RC3620 & RCM3620 Rotary Cuters 330-841M
Table of Contents
•
Always disconnect driveline from the tractor before
servicing the drivetrain and components powered by the
drivetrain. A person can become entangled in the drivetrain
if the tractor is started and the power take-off is engaged.
•
Always secure equipment with solid, non-concrete supports
before working under it. Never go under equipment
supported by concrete blocks or hydraulics. Concrete can
break, hydraulic lines can burst, and/or hydraulic controls
can be actuated even when power to hydraulics is off.
•
Do not operate a broken or bent driveline. Such a driveline
will break apart while rotating at high speeds and can cause
serious injury or death. Always remove the implement from
use until the damaged driveline can be repaired or replaced.
•
Do not raise one or both wings up with power take-off
engaged or drivelines rotating. Objects can be thrown by
rotating blades. Always keep people away from a cutter that
is operating.
•
Do not use cutter as a fan. Cutting blades are not properly
designed or guarded for this use.
•
The cutter must be operated with both wings attached.
Page
Removing one wing will increase risk of rollover. Removing
one or both wings will expose blades. Blades rotating at
1
high speed will cut body extremities and throw objects.
•
Do not engage power take-off while hooking-up or
unhooking the driveline, or while someone is standing near
13
the driveline. A person's body and/or clothing can become
entangled in the driveline.
28
•
Never place hands or feet under the deck or attempt to make
adjustments to the cutter with power take-off engaged.
39
Cutter blades rotating at high speeds cannot be seen and are
located close to the deck sides. Body extremities will be cut
47
off instantly.
•
This cutter is equipped with free-swinging cutting blades to
49
reduce shock loads. However, it is best to avoid striking
solid objects for your safety and to protect the cutter from
58
damage.
•
Keep everyone away from the cutter when folding or
unfolding the wings or when raising or lowering the cutter.
The cutter can pinch or crush a person when performing
these operations.
!
WARNING
To avoid serious injury or death:
•
Allow only persons to operate this implement who have
fully read and comprehended this manual, who have been
properly trained in the safe operation of this implement, and
who are age 16 or older. Serious injury or death can result
from the inability to read, understand, and follow
instructions provided in this manual.
•
Do not operate and/or travel across inclines where tractor
and/or implement can roll over. Consult your tractor's
manual for acceptable inclines the tractor is capable of
traveling across.
9/25/18
Advertisement
Table of Contents
