DSC HS2LCDWF v1.0 Installation Instructions Manual page 7

Power LED Indicates AC
ON I_____I 6
Present ON
Alarms Displayed While
ON I_____I 7
Armed
Auto-Scroll Open Zones
OFF I_____I 8
ON
[023] Third Keypad Options
Default Opt. ON
Armed LED On in
OFF I____I 1
Sleep Mode
Keypad Status Shows
ON I____I 2
Stay Arm
5th Terminal is Keypad
OFF I____I 3
PGM Output
OFF I____I 4
For Future Use
OFF I____I 5
For Future Use
OFF I____I 6
For Future Use
Temperature Display
OFF I____I 7
Enabled
Low Temperature
OFF I____I 8
Warning Enabled
NOTE: Programming options indicated in
with EN50131-1 and EN50131-3 standards. Section [023]: 1=OFF
[030] LCD Message
I _ __ _ _I _ ___ _I _ __ _ _ I _ __ __ I _ _ __ _ I _ _ __ _ I _ __ _ _ I _ __ _ _ I _ _ __ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ |
I _ __ _ _I _ ___ _I _ __ _ _ I _ __ __ I _ _ __ _ I _ _ __ _ I _ __ _ _ I _ __ _ _ I _ _ __ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ |
[031] Downloaded LCD Message Duration
Default: 000 I_____I_____I_____I (Valid entries are 000-255), 000=Unlimited Message
Display
This number represents the number of times the downloaded message must be
cleared before it is permanently removed. This message can be cleared by press-
ing any key.
[041] Indoor Temperature Zone Assignment
Default: 000 I _ _ _ _ _ I _ _ _ _ _ I _ _ _ __ I (Valid entries are 000-128)
[042] Outdoor Temperature Zone Assignment
Default: 000 I _ ____I _ __ __ I _ __ _ _ I (Valid entries are 000-128)
Power LED Indicates
AC Present OFF
Alarms Not Displayed
While Armed
Auto-Scroll Open
Zones OFF
OFF
Armed LED Off in Sleep Mode
Keypad Status Shows Stay/
Away Arm
5th Terminal is Keypad Zone
Input
For Future Use
For Future Use
For Future Use
Temperature Display Disabled
Low Temperature Warning
Disabled
GREY are required for systems compliant
[101]-[228] Door Chime for Zones 1-128
The keypad can be programmed to make up to four different chime sounds for
individual zones. e.g. for Zone 1 enter Section [101], for Zone 2 enter Section
[102].
Default Opt.
ON I____I 1
6 beeps
OFF I____I 2
'Bing-Bing' tone
OFF I____I 3
'Ding-Dong' tone
Alarm tone (4 second
OFF I____I 4
duration)
OFF I____I 5
Zone name
OFF I____I 6-8
For future use
[999] Reset Keypad Programming to Factory Defaults
1. Enter Installer's Code.
2. Press [ , ] or 999.
Limited Warranty
Digital Security Controls (DSC) warrants that for a period of 12 months from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, DSC shall, at its
option, repair or replace the defective equipment upon return of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control
of DSC such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or
improper application of the equipment. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of
any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of DSC. DSC neither
assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor
to assume for it any other warranty or liability concerning this product. In no event shall DSC be liable for any direct, indirect or
consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the
purchase, installation or operation or failure of this product. WARNING: DSC recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disrup-
tion, it is possible for this product to fail to perform as expected. Important Information: Changes or modifications not expressly
approved by DSC could void the user's authority to operate this equipment.
EN50131-1 Grade 2, Class 2, EN50131-6 Type B
Important Information: Changes/modifications not expressly approved by DSC could void the user's authority to operate this
equipment.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is
purchased under the following license terms:
• This End-User License Agreement ("EULA") is a legal agreement between You (the company, individual or entity who
acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada
Ltd. ("DSC"), the manufacturer of the integrated security systems and the developer of the software and any related products
or components ("HARDWARE") which You acquired.
• If the DSC software product ("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied by HARDWARE,
and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE
PRODUCT includes computer software, and may include associated media, printed materials, and "online" or electronic doc-
umentation.
• Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement
is licensed to You under the terms of that license agreement.
• By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree uncondi-
tionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement
or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and
You have no right to use it.
SOFTWARE PRODUCT LICENSE