IR Sync
Use IR Sync to form an audio channel between the transmitter and
receiver.
Note: The receiver band must match the band of the transmitter.
1. Select a receiver channel.
2. Tune the channel to an available frequency using group
scan or manually turn to an open frequency.
3. Power on the transmitter.
4. Press the SYNC button on the receiver.
5. Align the IR windows between the transmitter and the receiver so that
the IR LED illuminates red. When complete, Sync Success! appears.
The transmitter and receiver are now tuned to the same frequency.
IR
RX 1
RF
AUDIO
RX 2
RF
AD4Q
1
2
A
B
A
B
OL
OL
Axient Digital
SYNC
SYNC
Wireless Receiver
<15 cm (6 in.)
ULXD4
Digital Wireless Receiver
Note:
Any change to the encryption status on the receiver (enabling/disabling
encryption) requires a sync to send the settings to the transmitter. New
encryption keys for the transmitter and receiver channel are generated
on every IR sync, so to request a new key for a transmitter, perform an IR
sync with the desired receiver channel.
Setting the Frequency Manually
The transmitter can be manually tuned to a specific frequency, group, or
channel.
1. Navigate to the Radio menu and select F1 Freq or F2 Freq.
2. Scroll to select G: and C: to edit the group and chan-
nel, or select the frequency parameter (MHz). When ed-
iting the frequency, press O one to enable editing of the
first three digits, or twice to edit the last three digits.
3. Use the ∧∨ buttons to adjust the group, channel, or frequency.
4. Press O to save, and then press X when finished.
G: 1
470.450 MHz
AUDIO
RX 3
RF
AUDIO
RX 4
RF
AUDIO
NAVIGATE
3
4
A
B
A
B
OL
OL
PUSH
SYNC
SYNC
Sync Success!
sync
F1 Freq
C:1
RF Mute
RF Mute prevents transmission of the audio by suppressing the RF
signal, while allowing the transmitter to remain powered-on. The home
screen displays RF MUTED in this mode.
1. From the Radio menu, navigate to Output.
2. Choose one of the following options:
- On: RF signal is active
- Mute: RF signal is disabled
3. Press O to save.
CONTROL
POWER
Turning the transmitter off and on, or replacing the battery will restore
Output to On.
Power-on RF Mute
Power-on RF Mute places the transmitter in RF Mute mode immediately
when turned on.
• Starting with the transmitter off, press and hold the X button, and then
switch on the power
• Continue to hold the X button until the RF Muted message appears on
the home screen
Tip: To turn the RF Output on, navigate to Radio > Output and select
On.
Operating in Frequency Diversity Mode
Operating the AXDFD2 in frequency diversity mode with an Axient
Digital receiver enables simultaneous transmission of audio on 2 inde-
pendent frequencies.
1. Select a channel and navigate to the Frequency Diversity
setting: Advanced > Frequency Diversity .
2. Use the control wheel to select the Combining option.
3. Press ENTER to confirm and save.
4. Perform an IR sync to link the transmitter to the receiver.
In Frequency Diversity, the transmitter will operate on two adjacent re-
ceiver channels (1 and 2 or 3 and 4).
Turning Off Frequency 2 (Freq 2)
If a problem develops with one of the frequencies being used by the
transmitter, you can lock on to a single frequency by turning off frequen-
cy 2. Turning off one frequency allows the transmitter to continue pass-
ing audio while a clear frequency can be found for the second channel.
1. From the Radio menu navigate to F2 Ctrl.
2. Use the controls to set F2 to On or Off. When set to
On, the transmitter will pass audio using Freq 2.
8
RF Output
Mute
Need help?
Do you have a question about the AXIENT DIGITAL ADX2FD and is the answer not in the manual?