Advertisement
Quick Links
IBVRMU
Issue 8-7 27/06/2001
ECR 1226
BVR16, 32, 48 & 64MU
Microphones
Utilising software issue 'BVAM8-7'
Operating Instructions
Baldwin Boxall Communications Ltd.
Wealden Industrial Estate, Farningham Road
C O M M U N I C A T I O N S
Crowborough, East Sussex, TN6 2JR
Telephone: 01892 664422 Fax: 01892 663146
Website: www.baldwinboxall.co.uk
Email: mail@baldwinboxall.co.uk
Advertisement
Related Manuals for Baldwin Boxall BVR16M
Summary of Contents for Baldwin Boxall BVR16M
-
Page 1: Operating Instructions
BVR16, 32, 48 & 64MU Microphones Utilising software issue ‘BVAM8-7’ Operating Instructions Baldwin Boxall Communications Ltd. Wealden Industrial Estate, Farningham Road C O M M U N I C A T I O N S Crowborough, East Sussex, TN6 2JR Telephone: 01892 664422 Fax: 01892 663146 Website: www.baldwinboxall.co.uk... - Page 2 INDEX ……… Index ……… General Description ……… Connection & Communications ……… Instructions for Broadcasting a Live Emergency Microphone Message ……… Instructions for Using ‘EMERGENCY CALL ALL’ ……… Instructions for Broadcasting and Cancelling an Emergency Recorded Message Preceded by “Start of Test” and concluding with “End of “Test”. ………...
- Page 3 BVR16, 32, 48 & 64M – Voice Alarm Microphones The BVR M range is designed specifically for the Voice Alarm market to interface with the VIGIL range of amplifiers. The units connect to the BVR20 (Microdrive) controller and the VIGIL amplifiers to provide the following facilities:- 16, 32, 48 &...
- Page 4 Capsule 200 Ohms Dynamic noise cancelling, or Fist mic with PTT . 1.8m coil cord Frequency Response: 100Hz – 5kHz Sizes: Front Panel Size Bezel Size Bezel Cut-out Size Mic Type BVR16M 80mm 306mm 180mm 337mm 211mm 317mm 191mm BVR32M...
- Page 5 To Broadcast a Live Emergency Microphone Message 1) Lift plastic cover and depress Switch. The ‘Emergency Enable’ indicator will illuminate EMERGENCY ENABLE 2) Pre-recorded message 2 being broadcast, (example): Currently Broadcasting Message 2 3) Press ‘Select Zone’ of the desired zone or zones. If no zones are selected an ‘All Call’...
- Page 6 To Broadcast An Emergency Recorded Message, Preceeded by “Start of Test” and concluded by “End of Test” Message 1) ) Lift plastic cover and depress Switch. The ‘Emergency Enable’ indicator will illuminate EMERGENCY ENABLE 2) Zone Available Currently silent (no broadcast 3) Press zone select of the desired zone or zones.
- Page 7 To Broadcast An Emergency Recorded Message 1) Lift plastic cover and depress Switch. The ‘Emergency Enable’ indicator will illuminate EMERGENCY ENABLE 2) Zone Available Currently silent (no broadcast 3) Press zone select of the desired zone or zones Zone Selected If no zones are selected an ‘All Call’...
- Page 8 To Broadcast a Non Emergency (Paging) Microphone Message 1) Zone Available Zone silent, no broadcast 2) Press zone select of the desired zone or zones Zone Selected If no zones are selected an ‘All Call’ will be performed. 3) Press Speak key Broadcast Paging Microphone Wait for the Speak Now indicator to illuminate and speak into the microphone at approximately 150mm.
- Page 9 To Select Background Music (Aux 1-4), or Cancel Selection 1) Zone Available Zone silent, no broadcast 2) Press ‘Select Zone’ of the zone or zones req’d. Zone Selected 3) To select BGM Aux 1: Press ‘Select AUX MUSIC’ once Aux 1 selected Goto step (8) 4) To select BGM Aux 2: Press ‘Select AUX MUSIC’...
- Page 10 Zone Displays Zone silent, no broadcast Zone selected Emergency Microphone Broadcast Message 1 (Evacuate) broadcast Message 2 (Fire Alert 1) broadcast Message 3 (Fire Alert.2) broadcast Message 4 (Bomb Alert) broadcast Message 5 (All Clear) broadcast Message 6 (Test Messages) Message 7 (End of Test) Paging Microphone Broadcast Continued overleaf…...
- Page 11 Zone Displays continued Background Music – Aux 1 Background Music – Aux 2 Background Music – Aux 3 Background Music – Aux 4 Cancel Background Music Amplifier or Loudspeaker circuit fault Note: Even when a fault has been rectified the ‘F’ indication will remain on the zone display to indicate that a fault has occurred.
-
Page 12: Status Indicators (Not 7 Segment Leds)
Status Indicators (Not 7 segment LEDs) There are various LEDs that indicate the status of zones, messages or faults. Indicator Status Colour Description A Fault has been detected but not accepted by User. ‘System Fault’ Flashing with Press ‘Accept / Lamp Test’ to accept the fault. Buzzer Another yellow indicator to show where the fault has been detected will also be illuminated. - Page 13 BVRM DIL Switch Settings. BVR20 1 2 3 4 Emergency Mode Paging Mode 5 6 7 8 (Units) 0 0 0 0 FM1 Input 1 Priority 1 Input 1 Priority 12 0 0 0 0 1 only 1 0 0 0 FM2 Input 2 Priority 2 Input 2...