Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Skymaster ARF F-18
Summary of Contents for Skymaster ARF F-18
- Page 1 Skymaster ARF F-18 Instructions Manual...
- Page 2 first: Take out the front servos mount,...
- Page 4 install front fuel tank before installing nose cone...
- Page 5 connect nose cone to fuselage by 6 screw...
- Page 6 install main gear with setup air pipes for air breaks for the main gear...
- Page 8 install nose gear with after connecter...
- Page 11 setup the two screws for both rudder fins When you place the rudder fin in the fuselage, please make sure you use thread lock or a spring washer to set the screw in tightly. Also, make sure you check the screw regularly to ensure that the rudder does not come loose.
- Page 12 install two servos for the Elevator We suggest use of the Futaba # 9204. (#9151) or JR # 8425 (#8511 or 8611) servos for the elevator...
- Page 14 elevator shafts and servo arms must be installed first (make sure that there is a minimal lateral movement) and after which the servos mounts can be installed (included in the kit).
- Page 17 connect both push-pull rods for elevator servos control (the F-18 kit includes 2 rods for Elevators)
- Page 18 set-up elevator function for up / down movement for each to between 40 mm ~ 45 mm...
- Page 19 Glue the 6 Hinges for Ailerons with Flaps...
- Page 21 Glue the servos mounts for the Aileron servos and cut the hole then glue for Rudder Horns all Servo mounts must add glued Balsa for Strong more Note: Please make sure the servo is secured to the mount. The servo mount base should have enough surface area to hold it. If you only glue the servo mount directly to the wing surface without additional support may cause the whole thing to rip off in extreme conditions.
- Page 22 connect both push-pull rods for Aileron servos control (the F-18 kit includes 2 rods for Ailerons)
- Page 26 install the aileron servos, We suggest use of the JR # 3421servos for the ailerons...
- Page 28 before install two servos for both Flaps must be set up your RC system for Flaps Function We suggest use of the Futaba # 9204. (#9151) or JR # 8425 (#8511 or 8611) servos for the Flaps...
- Page 30 The new designed Flaps system very simple for set up your wings and no any Rods on out side...
- Page 31 If you do not want to use the new Flaps system, you will need to cut the holes for install the Flaps servos that Rods will be on out side.
- Page 32 first: Take out the cross spar for install both Fuel Tanks...
- Page 33 setup fuel pipe with "T" fitting for connect to both fuel tanks with over follow...
- Page 35 make the by-pass holes to fasten the dual wall tail pipe...
- Page 37 The tail flange has two brackets. Mark and drill holes in the brackets so they line-up with the holes in the right / left by-pass holes. make sure the engine is on the center line and adjust the engine position fore and aft as necessary...
- Page 39 setup the top cover for by-pass and set up the cross spar...
- Page 40 setup the front servo and make two piano wires control to the nose gear...
- Page 41 install the retracts control servo with break control servo, install two (2) valves for jet engine with the fuel pump...
- Page 43 If you want to make a cockpit detail for F-18, that do not install the full front servo mount, you must be cutting to half mount for install servos to the after space,...
- Page 44 install two batteries into nose cone for CG balance...
- Page 45 set-up ailerons function for up / down movement for each to between 12 mm ~ 18 mm...
- Page 46 set-up elevator function for up / down movement for each to between 40 mm ~ 45 mm...
- Page 47 set-up Flaps function for down movement 20mm~ 25mm for Talk off...
- Page 48 set-up Flaps function for down movement 60mm for Landing Home...
Need help?
Do you have a question about the ARF F-18 and is the answer not in the manual?
Questions and answers