Operation; Training - Husqvarna Z560X Operator's Manual

MANTENIMIENTO
Ruedas de apoyo
Las ruedas de apoyo mantienen el equipo en la
posición correcta para ayudar a evitar el corte al
ras en la mayoría de las condiciones del terreno.
No ajuste las ruedas para soportar el equipo.
INFORMACIÓN IMPORTANTE Ajuste las
ruedas de apoyo con el cortacésped en una
apoyo no se deben ajustar para sostener el
equipo.
Las ruedas de apoyo se pueden ajustar en tres
posiciones:
• Superior para hierba de 38 a 64 mm
• Intermedia para hierba de 64 a 102 mm
• Inferior para hierba de 102 a 127 mm
mm del suelo. No ajuste las ruedas para soportar
el equipo.
68
Limpieza
útil de la máquina. Hágase el hábito de limpiar
la máquina directamente después de cada uso
suciedad se adhiera.
No rocíe con agua la parte superior del equipo
regularmente el equipo y la parte inferior del
equipo con presión de agua normal. No utilice
lavadoras de alta presión ni equipos de limpieza
al vapor. Evite rociar el motor y los componentes
eléctricos con agua.
Deje que la unidad se enfríe antes de lavarla.
protección ocular durante el proceso
de limpieza y lavado.
Tornillería
Revísela diariamente. Inspeccione toda la
máquina para ver si faltan tornillos o si hay
tornillos sueltos.

OPERATION

Read the Safety
you are unfamiliar with the machine.

Training

mowers are far more maneuverable than typical
riding mowers.
Review this section fully before trying to move the
the mower or until becoming comfortable with
reduced ground speed. DO NOT move control
levers to the furthest forward or reverse positions
during initial operation.
First time users must become familiar with the
concrete or blacktop BEFORE trying to operate
aggressive maneuvers can damage turf.
Steering
To move forward and rearward
The direction and speed of the mower's
the control lever(s) on each side of mower. The
left lever controls the left wheel. The right lever
controls the right wheel.
First time users must push the mower (see
Moving Machine By Hand in the Operation
sit in the seat and start the engine (see Before
Starting in the Operation section). Adjust the
engine speed to idle but do not engage the
blades. Pull control levers inward. As long as the
control levers have not been moved forward or
Slowly move the two control levers forward
slightly. This will let the mower start moving
forward in a straight line. Pull the control levers
back to the neutral position and stop the mower
from moving.
mower to move rearwards. Push the control
levers forward to the neutral position to stop the
mower from moving.
To turn to the right
lever back towards the neutral position while
slow the rotation of the right wheel and cause the
machine to turn in that direction.
To turn to the left
While moving in a forward direction pull the left
lever back towards the neutral position while
slow the rotation of the left wheel and cause the
machine to turn in that direction.
To zero turn
two control levers back until the mower stops or
slows dramatically.
Then by alternating one lever slightly to the
forward position and the other in the reverse
WARNING
free of stones and other objects that could be
thrown by the rotating blades.
Roll Bar
Operate the unit with the roll bar in the raised and
locked position and use the seat belt. There is
no rollover protection when the roll bar is down.
seat belt. Raise the roll bar as soon as clearance
permits.
WARNING! The seat belt must be used
when the roll bar is in upright position.
Before Starting
WARNING
free from of stones and other objects that could
be thrown by the rotating blades.
1. Read the sections on Safety and Controls
before starting the machine.
2. Perform the daily maintenance before
starting (see Maintenance Schedule in the
Maintenance section).
3.
tank.
4. Adjust the seat to the desired position.
the engine can be started:
• The blade switch must be pressed down into
the disengaged position.
• The two steering / park brake controls must be
in the locked (outer) position.
Starting the Engine
1. Sit on the seat.
2. Raise the mower deck to the transport
position by pushing the lift pedal forward.
17