Eaton MTL5501-SR Instruction Manual page 30

Tables 6.1 and 6.2 show details of the modes available and the switch settings required to obtain them.
For ease of access, it is recommended that switches are set to the required mode before installation.
Table 6.1 indicates whether the output follows the input, or the output is the reverse or antiphase of
the input.
For example, in mode 0, o/p 1 = chA; so, if channel A switch is closed, then output 1 will also be
closed or short circuit. However, in mode 1, o/p 1 = chA rev., so if channel A switch is closed, then
output 1 will be the reverse, i.e. open-circuit.
Table 6 .1 - MTL5510 mode options
OFF OFF OFF OFF
ON
OFF
ON
OFF OFF
ON
OFF
ON
OFF OFF OFF
ON
OFF
ON
OFF OFF
ON
OFF
ON
Table 6.2 shows the MTL5510B modes. The logic tables and timing diagrams on the following
pages provide more detailed information on these modes.
Table 6 .2 - MTL5510B mode options
OFF OFF OFF OFF
ON
OFF
ON
OFF OFF
ON
OFF
ON
OFF OFF OFF
ON
OFF
ON
OFF OFF
ON
OFF
ON
*Mode of operation changed August 2015
MTL5510 & MTL5510B diagnostics
If an internal fault is detected, all outputs and channel LEDs will turn off and the red Fault LED
will turn ON.
22
Figure 6 .4: DIL switches for setting mode
Switch setting
MODE
1 2 3 4
0
OFF OFF OFF 1
ON OFF OFF 2
ON OFF OFF 3
ON OFF 4
OFF ON OFF 5
OFF 6
ON ON
OFF 7
ON ON
ON 8
OFF OFF ON 9
ON OFF ON 10
ON OFF ON 11
ON ON 12
OFF ON ON 13
ON ON ON 14
ON ON ON 15
Switch settings
MODE
1 2 3 4
0
OFF OFF OFF 1
ON OFF OFF 2*
ON OFF OFF 3
ON OFF 4
OFF ON OFF 5
ON ON OFF 6
ON ON OFF 7*
8
ON
OFF OFF 9
ON
ON OFF ON 10
ON OFF ON 11
ON ON 12
OFF ON ON 13
ON ON ON 14
ON ON ON 15
1 2 3 4
OFF position
ON position
o/p 1 o/p 2 o/p 3
chA chB chC
chA rev. chB chC
chA chB rev. chC
chA chB chC rev.
chA chB chC
chA rev. chB chC rev.
chA chB rev. chC
chA rev. chB rev. chC rev.
chA chB chC
chA rev. chB chC
chA chB rev. chC
chA chB chC rev.
chA chB chC
chA rev. chB chC rev.
chA chB rev. chC
chA rev. chB rev. chC rev.
Function
4-ch switch input (see MTL5510 mode 0)
2-ch each channel one input, two outputs
Same as mode 1 with all outputs phase
reversed
2-ch, 2-pole changeover output
1-ch with line fault output
As mode 4 with changeover outputs
1-ch with start-stop latch
As mode 2 with LFD enabled
4-ch switch input, see MTL5510 mode 8
2-ch with line fault output
As mode 9 with LFD changeover
As mode 10 with channel phase reversed
3-ch with normally-open LFD output
3-ch with normally-closed LFD output
2-ch monostable, pulse stretcher
4-ch switch input, see MTL5510 mode 15
o/p 4 i/p type
chD
chD
chD
chD
switch
chD rev.
chD
chD rev.
chD rev.
chD
chD
chD
prox.
chD
detector
chD rev.
+ LFD
chD
chD rev.
chD rev.
Equivalent
MTL5510
MTL5014
MTL2210B
MTL5510
MTL5017
MTL5510
INM 5500 Rev 10