Furuno CH-500 Operator's Manual page 100

APPENDIX 1 MENU TREE
CH-600
1 COM1
├
TX Power (High , Low)
├
TX Pulselength (Long , Short)
├
TX Rate (EXT., 1 to 10; default: 10 )
├
Interference LF (Off , On)
├
Interference HF (Off , On)
├
AGC-LF (0 , 1, 2, 3, 4, 5)
├
AGC-HF (0 , 1, 2, 3, 4, 5)
├
Auto Filter-LF (Wide, Std. , Narrow)
├
Auto Filter-HF (Wide, Std. , Narrow)
├
Reverberation (Off , On)
└
Volume (0.0 to 10.0, default: 0.0 )
2 COM2
├
Delete Track (No , Yes)
├
Mix Mode (Std. , Compress)
├
White Marker (Off, 1 to 31; default: Off )
├
Erase Color (Off, 1 to 30; default: Off )
├
Echo Colors (32 , 16, 8)
├
BKGD. Colors (1, 2 , 3)
├
Bearing (Relative , True)
├
Heading (-180 to +179º; default: +0º )
├
Roll Offset (-10.0 to +10.0; default: +0.0º )
├
Pitch Offset (-10.0 to +10.0; default: +0.0º )
└
Sensor Correct (-180 to +179º; default: +0º )
3 HOR.
├
TVG Level-LF (0.0 to 10.0; default: 4.0 )
├
TVG Level-HF (0.0 to 10.0; default: 4.0 )
├
TVG Distance-LF (0.0 to 10.0; default: 4.0 )
├
TVG Distance-HF (0.0 to 10.0; default: 4.0 )
├
Gain ADJ.-LF (-10 to +10; default: 0 )
├
Gain ADJ.-HF (-10 to +10; default: 0 )
├
RES. Color-LF (LOG , Linear, Square, Cube)
├
RES. Color-HF (LOG , Linear, Square, Cube)
├
Clutter-LF (0 , 1, 2, 3)
├
Clutter-HF (0 , 1, 2, 3)
├
Tracking Key (Position, Echo , Reverse)
├
Tracking Mode (Auto , Manual)
├
Auto Tilt (Off , ±2º, ±4º, ±6º, ±10º)
└
A-Scope (Off , On)
4 VERT
├
TVG Level-LF (0.0 to 10.0; default: 4.0 )
├
TVG Level-HF (0.0 to 10.0; default: 4.0 )
├
TVG Distance-LF (0.0 to 10.0; default: 4.0 )
├
TVG Distance-HF (0.0 to 10.0; default: 4.0 )
├
Gain ADJ.-LF (-10 to +10; default: 0 )
├
Gain ADJ.-HF (-10 to +10; default: 0 )
├
RES. Color-LF (LOG , Linear, Square, Cube)
├
RES. Color-HF (LOG , Linear, Square, Cube)
├
Clutter-LF (0 , 1, 2, 3)
├
Clutter-HF (0 , 1, 2, 3)
└
HOR. Range (×1 , ×2)
AP-4
(Continued on next page)
Bold Italic : Default