Download Print this page

KitchenAid KBSD602E Installation Instructions

Side by side built-in refrigerator

Advertisement

Quick Links

PRODUCT MODEL NUMBERS
KBSD602E
KBSD606E
Electrical: A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply
is required. It is recommended that a separate circuit serving only your refrigerator
be provided. Use an outlet that cannot be turned off by a switch. Do not use an
extension cord.
Water Pressure: A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have
questions about your water pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply:
IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system
gwoing to the water inlet valve of the refrigerator needs to be between 30 and 120 psi
(207 and 827 kPa).
IMPORTANT:
n It is recommended that you do not install the refrigerator near an oven, radiator, or
other heat source.
n Do not install in a location where the temperature will fall below 55°F (13°C).
n Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels
and contents of the refrigerator.

PRODUCT DIMENSIONS

n The depth from the front of the top grille to the back of the refrigerator cabinet is
5C\₈" (64.5 cm).
n The power cord is 84" (213 cm) long.
n Height dimensions are shown with leveling legs extended Z\₈" (3 mm) below
the rollers.

SIDE VIEW

*When leveling legs are fully extended to 1Z\v" (3.2 cm) below rollers,
add 1Z\₈" (2.9 cm) to the height dimensions.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Side By Side Built-In Refrigerator
KBSN602E
KBSD608E

OPENING DIMENSIONS

KBSN608E
To avoid tipping during use, the solid soffit must be within 1" (2.5 cm)
maximum above the refrigerator. If the solid soffit is higher than 1"
(2.5 cm) or one is not available, then the refrigerator must be braced.
If the anti-tip boards are needed, they must be attached to the rear wall
studs 80" to 90" (203 cm to 229 cm) above the floor. See "Install Anti-Tip
Boards" for more information.
NOTE: A clearance of Z\x" (1.3 cm) above the top grille must
be maintained in order for the top grille to be removed.
Model
36
42
48
NOTE: Flooring under refrigerator must be at same level as the room. Face of
cabinetry must be plumb.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Width A (as shown above)
Dimension B (as shown above)
35Z\x" to 35C\v"
4" (10.2 cm)
(90.2 cm to 90.8 cm)
41Z\x" to 41C\v"
7Z\x" (19.1 cm)
(105.4 cm to 106.1 cm)
47Z\x" to 47C\v"
13Z\x" (34.3 cm)
(120.7 cm to 121.3 cm)
Page 1 of 2
Ref. W10681447A
7/15

Advertisement

loading

Summary of Contents for KitchenAid KBSD602E

  • Page 1: Opening Dimensions

    Side By Side Built-In Refrigerator PRODUCT MODEL NUMBERS OPENING DIMENSIONS KBSN602E KBSD602E KBSD606E KBSD608E KBSN608E To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) Electrical: A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply maximum above the refrigerator.
  • Page 2: Top View

    TOP VIEW DOOR SWING DIMENSIONS The location must permit both doors to open to a minimum of 90°. Allow 5" (12.7 cm) minimum space between the side of the refrigerator and a corner wall. NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model.

This manual is also suitable for:

Kbsd606eKbsd608eKbsn602eKbsn608e