Related Manuals for Redring PURE 8.5kW
Summary of Contents for Redring PURE 8.5kW
- Page 1 PURE 7.5/8.5/9.5/10.5kW Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration...
-
Page 2: Table Of Contents
Contents Installation Guide 1 – Pack Contents 2 – Installation Check List 3 – Important Safety Information 4 – General Installation Layout Guide 5 – Important Installation Information 6 – Fixing the Shower to the Wall 7 – Product Positioning Guide 8 –... -
Page 3: Pack Contents
1. Pack Contents Please make sure ALL components are included before starting the installation. Shower Unit Shower Handset Riser Rail Tube Riser Rail Brackets x 2 Riser Rail Height Adjuster Flexible Shower Hose Screw Pack Installation and User Instructions 2. Installation Check List Check that the water supply will satisfy requirements Check that water &... -
Page 4: Important Safety Information
3. Important Safety Information Products manufactured by Redring Xpelair Group are safe and without risk provided they are installed, used and maintained in good working order in accordance with our instructions and recommendations. MAINS SERVICE CONNECTIONS: The shower unit is supplied for right hand entry, please see Section 8 &... -
Page 5: General Installation Layout Guide
4. General Installation Layout Guide • Plan your installation carefully. Check on • For example the mains feed to a toilet as the nearest and most accessible rising this may cause a drop in pressure to a level main water supply, this may be beneath that is too low for the shower unit to work the bath or in the loft, where it feeds the correctly. -
Page 6: Important Installation Information
5. Important Installation Information Shower installation must be carried out by a suitably qualified person and be in accordance with BS 7671 (IET wiring regulations), building regulations, water regulations and / or any specific local water company regulations in force and should be in accordance with BS EN 806. -
Page 7: Product Positioning Guide
7. Product Positioning Guide Shower unit can be mounted either side of riser rail. Height of shower handset and shower to suit user’s requirements 25mm minimum Spillover level Outline of bath or shower tray Spillover level... -
Page 8: Plumbing Connections
8. Plumbing Connections 5. If rear entry pipe work is used we The shower back plate incorporates into the recommend the use of a suitable sealant lower right side a removable corner section to seal around the incoming pipe work to to allow easy access when deciding on and prevent water entering the wall. -
Page 9: Electrical Connections
9. Electrical Connections The electrical installation must be in 1. The incoming cable should be hidden. Connect as follows: accordance with the current BS 7671 (I.E.T. wiring regulations) and part P of the building Earth cable to terminal marked and / or local regulations. Neutral cable to terminal marked N The shower unit is designed for a single phase Live cable to terminal marked L... -
Page 10: Fitting The
Electrical Connections Cont.. IMPORTANT: The use of connections within the unit or other points in the shower circuit to supply power to other equipment such as an extractor fan or pump etc will invalidate the guarantee. The diagram below shows a schematic wiring diagram. 1. -
Page 11: Riser Rail Fitting Instructions
11. Riser Rail Fitting Instructions 1. Establish position for the riser rail, and mark the wall for the lower mounting bracket. Make allowances for the tallest person likely to use the shower regularly. 2. Remove covers from the wall brackets. 3. -
Page 12: Commissioning The Shower
12. Commissioning The Shower IMPORTANT: Make sure that the electricity supply has been disconnected at the isolation switch. 11. Now adjust the bottom rotary temperature 1. Turn the top rotary power selector knob; control knob clockwise for hotter water identified by the solid blue line, to the Cold allowing a few seconds for the temperature setting. -
Page 13: Troubleshooting Checklist For The Installer
13. Troubleshooting Checklist For The Installer IMPORTANT: The following check list is provided for the benefit of the qualified installer. WARNING: SWITCH OFF THE ELECTRICAL ISOLATION SWITCH BEFORE REMOVING THE FRONT COVER TO MAKE CHECKS. Q. Poor or no control over water flow. Q. -
Page 14: Important Safety Information
1. Important Safety Information Products manufactured by Redring Xpelair Group are safe and without risk provided they are installed, used and maintained in good working order in accordance with our instructions and recommendations. FOR THE USER: DO NOT operate the unit if the handset or shower hose becomes damaged. -
Page 15: Operating The Shower
2. Operating The Shower 1. Switch on the electrical supply at the 4. The temperature control knob alters the isolation switch. outlet temperature by increasing or reducing the flow rate of water through the shower NOTE: We recommend that you do not stand unit. -
Page 16: How Your Shower Works
3. How Your Shower Works 1. The cold incoming water is heated 6. A thermal cut-out is mounted on top of the instantaneously as it flows over the heating heat exchanger. elements in the heat exchanger assembly. Stage 1 switches the power off to the 2. -
Page 17: Troubleshooting And Faqs
5. Troubleshooting and Frequently Asked Questions IMPORTANT: If an answer requires removal of front cover, please seek help of qualified person. • If the performance of your shower deteriorates in service please follow the self help items detailed below before seeking professional advice from the installer. •... -
Page 18: Troubleshooting Checklist For The Installer
This guarantee does not affect your f) For the service work to be undertaken free statutory rights. of charge, the work must only be undertaken by Redring Xpelair Group Limited, or our approved agents. Service and Repair: service.request@redringxpelair.com or 08443727766*... -
Page 19: Energy Related Product Directive (Erp)
7. Energy Related Product Directive (ErP) This information shows how our products pass the relevant European Union Energy Directives (ErP). Supplier's / Manufacturer REDRING Supplier's Model Identifier PURE Supplier's Model Number RPS7 RPS8 RPS9 RPS10 Declared Load Profile Energy Efficiency Class... - Page 20 Newcombe House, Newcombe Way, Orton Southgate, Peterborough, PE2 6SE Tel: +44 (0) 844 372 7761 Fax: +44 (0) 844 372 7762 Technical Service Tel: +44 (0) 844 372 7766 Technical Service Email: Service.request@redringxpelair.com *Calls cost 7p per minute plus your telephone company's network access charge. DATE OF PUBLICATION 10/10/2017 Rev.