Stanley SK58 Service Manual page 16

2. Apply grease and install an o-ring (21) onto the flow
sleeve tube.
3. Apply clean hydraulic fluid and install 4 push pins
(58) into the holes in the top of the flow sleeve tube.
One end of each push pin contains a machined
surface. This surface must be facing up as each push
pin is installed. Each push pin must slide freely in or
out of the hole. If a push pin does not slide freely or
seems to stick, the hole may contain contamination
or the top edge of the hole contains a burr. Remove
burrs with a deburring tool, clean the hole thor-
oughly and try the push pin again.
4. Tap the roll pin (33) into the hole on the automatic
valve body (56).
5. Apply grease and install an o-ring (21) onto the
automatic valve body.
6. Lubricate with clean hydraulic fluid and install 2
push pins (57) into the holes in the valve body. One
end of each push pin contains a machined surface.
This surface must be facing up as each push pin is
installed. Each push pin must slide freely in or out
of the hole. If a push pin does not slide freely or
seems to stick, the hole may contain contamination
or the top edge of the hole contains a burr. Remove
burrs with a deburring tool, clean the hole thor-
oughly and try the push pin again.
7. Lubricate the automatic valve (32) with clean
hydraulic fluid and install it into the valve body.
The automatic valve must freely slide back and
forth. If it does not, the valve body or valve may
contain contaminants or the bore of the valve body
contains burrs. Remove the push pins and scrub the
bore of the valve body with emery cloth and then
thoroughly clean the bore, push pin holes and valve.
Reinstall the push pins and valve.
8. Grasp the automatic valve body and valve so that
one or more fingers are gripping the valve to prevent
it and the push pins from falling out when the valve
body and valve are turned upside down (roll pin
facing down). Place the assembly on top of the flow
sleeve making sure the roll pin aligns with the
appropriate hole in the flow sleeve.
9. Lubricate the piston (29) with clean hydraulic fluid
and install into the top of the automatic valve body.
Apply grease and install a new o-ring (28) into the
groove in the piston (water flush models only).
10. Install the washer (27), smaller diameter first, over
the stem of the piston and onto the automatic valve
body.
11. Install the accumulator assembly over the stem of
the piston and down to the top of the automatic
valve body.
12. Insert the air tube (1) (or water tube if applicable)
into the top of the accumulator ensuring it aligns
with the hole in the piston.
13. Use a felt tip marker to place a mark on the accumu-
lator cylinder and the accumulator housing to align
the tube connector with the port in the accumulator
housing.
14. Apply grease liberally to the o-ring surfaces on the
accumulator, automatic valve body, flow sleeve tube
and to the bore of the accumulator housing.
15. Place the accumulator housing over the top of the
accumulator, ensure that the felt pen marks are
alligned, and then tap it down until the lower part of
the housing covers the o-ring on the flow sleeve
tube.
16. Lay the completed assembly on its side being careful
to prevent movement of the flow sleeve. Remove the
assembly fixture.
17. Place the completed assembly horizontally in a vice
with soft jaws, oil ports up, and clamp on the flow
sleeve tube.
18. Apply grease and Install a new cup seal (93) with
lips facing down, the washer (92), new rod seal (91)
with lips facing up, and a new o-ring (90).
19. Install the motor over the side rods and into the flow
sleeve tube ensuring the roll pin is correctly aligned
with the hole in the flow sleeve and the motor
control valve is oriented correctly with the handles.
20. Install the 4 side rod nuts. Tighten in 20 ft lb/25 Nm
increments to 75 ft lb/100 Nm in a cross pattern.
21. Apply grease and install new o-rings (44 & 45) to
the blower tube nut. Install the blower tube nut to
the accumulator housing.
22. Install the charge valve (14).
23. Charge the accumulator with 600 psi/42 bar nitrogen
as described in the "CHARGING THE ACCUMU-
LATOR" section of this manual.
24. Apply grease and install a new o-ring (13) onto the
charge valve cap (12). Install the charge valve cap.
14