Page 1
Operations, Service, and Parts Manual LEEBOY MODEL 6150 CONVEYOR PAVER Manual No. 1016971-01 This manual applies to Serial Number 146995 and above.
Page 3
Thumb Index SAFETY INFORMATION AND SPECIFICATIONS COMPONENT LOCATION OPERATION MAINTENANCE SCHEMATICS ILLUSTRATED PARTS LIST...
Page 4
LeeBoy reserves all copyright and other rights in this manual and the manual’s content. No part of this manual may be reproduced or used in any way without the written permission of VT LeeBoy, Inc., except as necessary to operate LeeBoy equipment.
Page 6
Plus +1® Controller ......4-18 Driving the Paver ......4-18 LeeBoy 6150 Conveyor Paver...
Page 7
Preparing Paver for Maintenance ....5-4 Every 10 Hours or Daily Routine Maintenance ... . 5-4 LeeBoy 6150 Conveyor Paver...
Page 8
Rear Tire Liquid Ballast ..... . . 5-22 Repack Front Wheel ......5-23 viii LeeBoy 6150 Conveyor Paver...
Page 9
C4 Dash to Pedestal Jumper Harness ....6-25 C3 Dash to Pedestal Jumper Harness ....6-27 LeeBoy 6150 Conveyor Paver...
Page 10
Spray Down ....... . 7-42 Tow Point Assembly ......7-44 LeeBoy 6150 Conveyor Paver...
Page 11
Option - HD Screed Extension Assembly - Right ....7-114 Option - HD Screed Slide Plate Assembly ....7-116 LeeBoy 6150 Conveyor Paver...
Page 12
Hydraulic Hose Schedule - Standard Unit ....7-156 Alphabetical Parts Index ......7-160 LeeBoy 6150 Conveyor Paver...
Page 13
VT LeeBoy, Inc. is proud to be ISO 9001 certified. The International Standards Organization (ISO) establishes guidelines to ensure that products and services are safe, reliable and of good quality. ISO certifies companies who demonstrate compliance with all aspects of product safety, customer satisfaction, efficiency, environmental stewardship and social responsibility.
Page 17
Indicates a hazardous situation which, new matching labels. Replacement safety labels are if not avoided, could result in death or serious injury. available from your LeeBoy authorized dealer (see contact information in Section 2). Indicates a hazardous situation which, if not avoided, could result in minor or moderate You can find more information about occupational health injury.
• Failure to observe these directions could result in electrocution or death. • Contact LeeBoy or an authorized LeeBoy dealer for additional training. • Make sure you are aware of all laws and regulations Electrocution Hazard that are in effect for the location in which the paver is operated.
Page 19
When operating machinery there is a risk for Never modify the LeeBoy machine without the written fire. Always have appropriate safety consent of LeeBoy. Any modification can affect the safe equipment available. operation of the paver and may cause personal injury or death.
Page 20
• Never check for a hydraulic fluid or fuel leak with your hands. Always use a piece of wood or cardboard. Have your authorized LeeBoy dealer or distributor repair the damaged parts. LeeBoy 6150...
Natural separation will occur in about 48 to 72 hours. • Only use replacement parts approved by LeeBoy. Get medical attention as soon as possible. Other replacement parts may affect warranty •...
Never allow anyone to reach into the machine during use. • To avoid electrolyte loss, DO NOT tip batteries more than 45 degrees. • DO NOT tow the paver, except to remove from road or to load on trailer. LeeBoy 6150 Conveyor Paver...
While the machine is equipped with a beacon and a exceeded and can result in damage to the rim and tire. work light, contact your authorized LeeBoy dealer for additional lighting packages if working under these conditions.
• Disconnect battery before working on the electrical system or welding on the machine. • Avoid lubrication or mechanical adjustments while the paver is in motion or while engine is operating. 1-10 LeeBoy 6150 Conveyor Paver...
DANGER safety decals in the proper locations. (Figure readable and located on the paver as designated by 1-1) For additional help, refer to the parts listing in LeeBoy. Section 7 and contact your authorized LeeBoy dealer to order a replacement kit. Both Sides Both Sides...
5. Obtain replacement safety decals or signs from 4. Small air pockets can be pierced with a pin and your authorized LeeBoy dealer. smoothed out using a piece of the decal backing. 5. When decal is completely smoothed, carefully Decal Installation (Sticker Type) remove top paper.
PURCHASE PRICE OF THE PRODUCT. Attachments not manufactured or installed by LB Performance. Liability for incidental or consequential damages of any type including, but not limited to, lost profits or expenses of acquiring replacement equipment. Miscellaneous charges. LeeBoy 6150 Conveyor Paver...
Sales Representative: Dealership Name: Dealership Address: Dealership Phone: Record of Ownership Please complete the following information for use if you need to contact LeeBoy for service, parts or literature. Machine Model Number: Product Serial Number: Date of Purchase: Nameplate The nameplate contains the model and serial numbers used to identify the machine and its components for parts or service information.
SPECIFICATION CHARTS The specifications provided in this section include Replace original equipment only with screed weights, dimensions, performance, and torque components approved by your LeeBoy dealer. values for both metric and standard inch fastener. 7’ 8” (2.3 m) 8’ 6”...
Page 31
Table 2-6. Electrical Specifications ITEM SPECIFICATION Battery One 12 Vdc Maintenance Free, 12 Volts, 1000 CCA 12-Volt, Negative-Ground, 100 Amps. Manual belt Alternator tension mechanism keeps serpentine belt under tension at all times. Starter 12-Volt, Negative-Ground LeeBoy 6150 Conveyor Paver...
Page 32
MAIN: 1.375 in (35 mm) 1 in (25.4 mm) Vibration Two (2) hydraulic vibrators producing 2400 vpm. POSITIVE: 2 in @ 10 ft (50.8 mm @ 3 m) Positive/Negative Crown NEGATIVE: 1.50 in @ 10 ft (38.1 mm @ 3 m) LeeBoy 6150 Conveyor Paver...
Place one wrench on the connector body and tighten the swivel nut with the second to the torque shown in the following table: NOTE: The torque values shown are based upon 1 1/4 lubricated connections. 1 3/8 LeeBoy 6150 Conveyor Paver...
TS = TD * L / LH TS = TD * L / √(L • To estimate the crowfoot size (E) E = Drive Size * 0.5 + Distance between Drive and Open End + Wrench Size * 0.5774 LeeBoy 6150 Conveyor Paver...
Page 36
2. The flats method is most accurate for the first assembly cycle. For multiple disassembly and assembly cycles, torque values are more reliable. 3. Tightening two (2) flats or more may damage seal faces. LeeBoy 6150 Conveyor Paver 2-10...
Page 37
2. Torque values apply to bolts that are plated or coated in light engine oil. 3. Before assembly, lubricate O-Ring with light oil (SAE 10W or 20W). LeeBoy 6150 Conveyor Paver 2-11...
Page 38
2. When using a male tapered pipe thread with a female straight or parallel pipe thread, maximum values are 50% of those listed in the table above. 3. If thread sealant is used, maximum values shown should be decreased by 25%. LeeBoy 6150 Conveyor Paver 2-12...
Engine The LeeBoy Model 6150 This section describes the major components for the Conveyor Paver is equipped LeeBoy 6150 Conveyor Paver. This wheeled paver is with a Kubota (V3800- designed with front “bogie” tires and rear heavy-duty, TIEF4BFT4) diesel engine.
The auger can be controlled at the operator The LeeBoy 6150 Conveyor Paver is equipped with the platform or by a screed Legend® screed system with propane heat. Electric operator using the remote heat is an option.
Controls depth of the screed endgate. Endgate Depth Screw Adjustable Height Push These adjustable rollers push the material delivery truck along as it delivers Rollers asphalt into the paver hopper. Manually adjusts at five different heights. Leeboy 6150 Conveyor Paver...
Optional Component: Engages truck hitch function. Engages the truck hitch to the material truck Truck Hitch wheels. Set switch to the IN position to engage the hitch. The OUT position disengages hitch (Option) from the material truck wheels. Ignition Starts and stops engine. Leeboy 6150 Conveyor Paver...
Page 45
Extends or retracts right screed extension. Push switch IN to retract right screed extension. Right Extension Push switch to OUT to extend right screed extension. (Switch also located on the remote box on Switch right side of paver.) Leeboy 6150 Conveyor Paver...
Flight Screw Controls the depth of the asphalt. Screed operator control box with switches to extend/retract screed Remote Screed Controls extension, auger manual override, cut-off gate control and raise/lower asphalt slope. Leeboy 6150 Conveyor Paver...
Controls flow of pro- Propane Tank Opens and closes Right Burner Valve pane to right screed Open/Close Valve propane pressure. burner. Burner Ignitor Wand Used to light burners. Controls flow of pro- Burner Ignitor Valve pane to ignitor. Leeboy 6150 Conveyor Paver...
Turns auger on and screed plates. Press Auger off. the button again to reheat the screed if needed. Turns the electric heat Power Switch system on and off. 3-10 Leeboy 6150 Conveyor Paver...
General Information Initial and Daily Inspection The following inspection is essential and should be The LeeBoy Model 6150 Conveyor Paver is a wheeled performed before the initial start-up. Visually inspect the paver with the versatility for “patch paving” along with a unit to check its general condition and for familiarization.
OFF position and remove wing nut into place. Reverse procedure to unlock the key. screed. NOTE: If the engine does not shut down when key is turned OFF, press the E-Stop button on the control panel to terminate power. LeeBoy 6150 Conveyor Paver...
3 - Engine Coolant Temperature up in the DPF, requiring more frequent regeneration. 4 - Electrical Potential Voltage 5 - Hydraulic Oil Temperature 6 - Soft Key Banner LeeBoy 6150 Conveyor Paver...
NOTE: The generator is set at the factory to default Increases the engine speed (RPMs). at 1800 RPMs. It is recommended that you use the 1800 RPM preset for optimum Decreases the engine speed (RPMs). performance. LeeBoy 6150 Conveyor Paver...
(SPN) and Failure Mode Indicator (FMI). (Figure 4-9) It may also display text description and ID/Name of the device that transmitted the message. Use the UP/ DOWN soft keys to scroll through list if needed. Figure 4-9. Active Diagnostics Screen LeeBoy 6150 Conveyor Paver...
Figure 4-11. System Info Screen Regeneration Symbol Screen Press the UP/DOWN soft keys to scroll to the screen with application and configuration information. (Figure 4-12) Figure 4-14. Needs Regenerating Screen Figure 4-12. Application and Configuration Information Screen LeeBoy 6150 Conveyor Paver...
Colors. (Figure 4-17 and 4-18) Set your preference for day or night vision using the +/– soft keys. Figure 4-15. Machine Inhibiting DPF Regeneration Screen Figure 4-17. Set Night Vision Color Preferences Screen Figure 4-16. Parked Regeneration Overview Screen 4-10 LeeBoy 6150 Conveyor Paver...
Page 59
Units. (Figure 4-21) Set your unit preference using the +/– soft keys. (US Standard, Metric kPa or Metric Bar.) Figure 4-19. Set Brightness Of Backlight Screen Figure 4-21. Set Unit Preferences Screen LeeBoy 6150 Conveyor Paver 4-11...
EXTREMELY HIGH. BE SURE EXHAUST WILL NOT COME INTO CONTACT WITH ANY COMBUSTIBLE MATERIALS. NOTE: During the regeneration, the Engine Speed will increase and there may be a noticeable sound difference. The HEST Lamp will appear during the process. 4-12 LeeBoy 6150 Conveyor Paver...
Page 61
Example Requiring Use of UP/DOWN Soft Keys Figure 4-26. Parked Regeneration Blue Screen Continue to monitor surrounding areas during the process. If unsafe conditions develop, shut the unit off immediately. Figure 4-25. Parked Regeneration Instructions Screen LeeBoy 6150 Conveyor Paver 4-13...
Figure 4-29. Regen Level 1 Notice 4-28) Click on the soft key to remove the popup message. When the parked regeneration process is complete, the engine will return to normal idle speed. Figure 4-28. Parked Regeneration Green Popup Message Screen 4-14 LeeBoy 6150 Conveyor Paver...
Page 63
3. Set the engine to low idle. 4. Uninhibit regeneration. 4. Uninhibit regeneration. 5. Apply the parking brake (if equipped). 5. Apply the parking brake (if equipped). Figure 4-33. Secondary Regen Level 3 Notice Figure 4-31. Secondary Regen Level 2 Notice LeeBoy 6150 Conveyor Paver 4-15...
Page 64
(Figure 4-34) technician. IMMEDIATELY take the machine to a safe location, shut down, and contact a qualified service facil- ity. (Figure 4-35) Figure 4-34. Regen Level 4 Warning Figure 4-35. Regen Level 5 4-16 LeeBoy 6150 Conveyor Paver...
When this lamp is illuminated, a REGEN cannot be per- formed and soot levels will continue to rise. Unless hazardous conditions exist, the REGEN Inhibit switch and this lamp should remain off. LeeBoy 6150 Conveyor Paver 4-17...
Plus One Light Figure 4-37. Driving the 6150 Conveyor Paver Driving the Paver The LeeBoy 6150 Conveyor Paver is a wheeled paver especially useful when paving over irregular grades. Equipped with PosiTrac (positive track--a traction lock system) and pivot steering, this paver offers versatility in Figure 4-36.
Operation Activate/Deactivate Operator Steering and Speed Control Control Station The LeeBoy 6150 Conveyor Paver is steered by steering wheel, with forward/reverse direction and Only one operator control station can be activated at a speed controlled via joystick. The RUN/STOP switch time for the paver to function.
Always spray down the LeeBoy Model 6150 Conveyor (such as sand or other soft bases). The 6150 paver is Paver before and after paving. Spray any part of the equipped with Posi-Trac (positive traction) and Pivot...
Hose Reel cold screed bottom. Spray Wand Figure 4-43. Paving with the 6150 Conveyor Paver Figure 4-42. Spray Down Wand Generally, one heat cycle is all that is needed--hot asphalt will keep the screed heated as you pave. An Start at the front of the machine and work rearward, us-...
Reduce pressure on the propane pressure regulator gauge to two pounds (.14 bar) in Right these conditions. DO NOT attempt to regulate Burner the burner with the burner valve. Left Burner Figure 4-46. Main Screed Burner Ignition 4-22 LeeBoy 6150 Conveyor Paver...
Page 71
Electric Heat Option Screed Extension: When using the screed extension(s), light the screed The LeeBoy 6150 Conveyor Paver offers an optional extension(s) after the main screed burner has been lit electric heat system to heat the screed, including the following these additional steps: screed extensions, in lieu of the burner system.
Operating in cold temperatures may affect 3 - Conveyors the screed plate temperature slightly.) If the heat cycle has completed but the screed plates still require heating, restart the cycle by repeating Step 4. 4-24 LeeBoy 6150 Conveyor Paver...
Operation Conveyors Under Auger Material Cut-Offs The LeeBoy Model 6150 Conveyor Paver is equipped The Under Auger Material Cut-Offs are another with two automatic conveyors that deliver asphalt evenly important function of the paver. (Figure 4-52) The cut- to produce a smooth asphalt mat. (Figure 4-51) offs are used primarily to control the flow of asphalt to the screed and hydraulic screed extensions.
A tow point cylinder gauge is located on both sides of the extended screed is the same as the rear edge of the the LeeBoy 6150 Conveyor Paver. (Figure 4-53) main screed, resulting in a smooth mat the length of the screed.
Page 75
NOTE: Too much adjustment up or down may cause below the screed. (Figure 4-54) uneven pavement. 11. If making a cold joint, set the endgate down about 1/4 inch (6.35 mm) for a nice, even edge. LeeBoy 6150 Conveyor Paver 4-27...
(Figure 4-58) It detects the material height and controls the auger height by automatically turning the auger on and off. Material Height Sonic Dial Sensor Mount Main Auger Controls Screed Auger Switch Figure 4-59. Sonic Auger Controls Sequence 4-28 LeeBoy 6150 Conveyor Paver...
Figure 4-60. Paving Starting to Pave The LeeBoy 6150 Conveyor Paver provides superior paving for driveways, small to large parking lots, and secondary roads. The paver is equipped with electric and manual thickness controls, and can be operated Bolt Slots from either side of the operator platform.
Figure 4-64. Loosen Lock-Down Bolts 10. Begin paving, moving slowly at first to adjust the screed if needed. 11. Make a paving pass until the asphalt level in the hopper is low. 4-30 LeeBoy 6150 Conveyor Paver...
AOA remains unchanged, and the texture of the material on the mat is uniform. (The augers also operate more efficiently if the material level remains at half-auger.) LeeBoy 6150 Conveyor Paver 4-31...
4-67) NOTE: The screed extension should be hot before making any adjustments. Angle-of-Attack Adjuster Figure 4-68. Paving Road with the 6150 Paving Tips • Asphalt thickness is directly related to lasting pavement. Only a half-inch makes a big difference. •...
6. Position paver in center of trailer. Lower the screed. 8. Shut down the engine. 9. Secure paver to transport using the following tie- down procedures. Figure 4-69. Correct Position Figure 4-70. Incorrect Position LeeBoy 6150 Conveyor Paver 4-33...
DO NOT allow the screed to strike the Figure 4-71. Tie-Down Locations ramp as this can damage bearings on the thickness control screws or welds on the leveling arms. A longer ramp to reduce the loading angle may be needed. 4-34 LeeBoy 6150 Conveyor Paver...
The umbrella kit option provides shelter from sun and other weather conditions for the operator. The umbrella kit assembly includes the mounting bracket and umbrel- la frame assembly that can be mounted on either side of the screed handle. LeeBoy 6150 Conveyor Paver 4-35...
Place switch in the EXT position to move the screed and a set slope to the other end. extension in or out. Most states require this technology for state road paving jobs to ensure smoothness and continuity on roadways. LeeBoy 6150 Conveyor Paver 4-37...
Vertical Lift To attach the tunnel extension: Loosen the wing bolt on extension. 2. Remove the tube cover. 3. Slide tunnel extension into the tube. 4. Tighten the wing bolt. Figure 4-78. One-Foot Screed Extension 4-38 LeeBoy 6150 Conveyor Paver...
(2) front wheel spindle bearings. This kit combines these 12 individual grease points into one lubrication point located beside the fuel filler cap. (Figure 4-82) Conveyor Lube Kit Lubication Point Fuel Cap Figure 4-81. Conveyor Lubrication Point LeeBoy 6150 Conveyor Paver 4-39...
Page 88
3. Turn the power crown selector switch OFF when not using this feature in order to extend/retract the right screed extension. Power Crown Switch Figure 4-83. Power Crown Option 4-40 LeeBoy 6150 Conveyor Paver...
Before performing any maintenance procedures on the engine service information. LeeBoy Model 6150 Conveyor Paver, review the safety information in Section 1. When performing any routine maintenance, always include the previous routine maintenance hours in the Always use the appropriate tools higher hourly schedule.
2. Lubricate the required parts. (Page 5-6) 3. Check beacon and work lights are functioning. Replace any lighting components if needed. 4. Check battery cables and connections. (Page 5-18) 5. Check coolant level. Fill if needed. LeeBoy 6150 Conveyor Paver...
Lubrication Proper lubrication is necessary to maintain the The lubrication intervals outlined LeeBoy Model 6150 Conveyor Paver at top efficiency. below are based upon average operating conditions. Periodic lubrication of moving parts is an essential If working in severe, dusty or wet conditions, more part of preventive maintenance that minimizes risk for frequent lubrication may be necessary.
Figure 5-2. Torque Hub Plugs in 3 O’Clock Position Changing oil and cleaning the paver should only be done in a designated area where the oil and chemicals can be contained. Discard these by-products in accordance with environmental regulations. LeeBoy 6150 Conveyor Paver...
6. After the conveyor chain tension is set, retighten locknuts and bolts holding the flight chain assembly. Repeat steps 1 through 4 for the opposite side. 8. Grease front and rear conveyor tubes at grease blocks on each side of conveyor. LeeBoy 6150 Conveyor Paver...
4. Turn the chain adjuster to loosen or tighten the chain, leaving approximately 1/4-inch of slack. DO Tension NOT overtighten. Adjusters 5. Retighten jam nuts. Figure 5-5. Auger Drive Chain Bolts 6. Repeat steps on the opposite conveyor drive chain. LeeBoy 6150 Conveyor Paver...
5” Conveyor Flap Position ON Position Figure 5-6. Screed Extension Top Guide Adjustment 1 - Screed Extension Top Guide Conveyor 9” Flap 2 - Allen Screws Position 3 - Hold-Down Bolts Figure 5-7. Adjustment Measurements 5-10 LeeBoy 6150 Conveyor Paver...
Page 99
2. Slide the actuator arm IN or OUT to bring the travel limits into tolerance. This may require several Figure 5-8. Actuator Arm - Setscrews A and B adjustments before the correct position is obtained. LeeBoy 6150 Conveyor Paver 5-11...
Maintenance Engine Maintenance Torque Hub Hydraulic Motor Gear Adjustments The LeeBoy 6150 Conveyor Paver features the latest in engine technology. Tier 4 engines comply with emission Torque hub hydraulic motors are requirements established by the U.S. Environmental calibrated and set at the factory. These adjustment...
4. Remove the dipstick from the engine and checking the oil level. The oil level should be above the ADD mark--but not above the FULL mark--on the dipstick. Add oil if needed. LeeBoy 6150 Conveyor Paver 5-13...
Install the new filter element onto the filter head. Carefully tighten the filter (by hand only). DO NOT smoke or change fuel filter near open flames as diesel fuel is highly combustible. Be careful not to spill fuel. 5-14 LeeBoy 6150 Conveyor Paver...
9. Install the new fuel filter element onto the filter head, 2. Loosen and remove the filter body, then clean it with carefully tightening the element by hand. light oil. 10. Start the engine and check for any fuel leaks. 3. Reinsert and tighten. LeeBoy 6150 Conveyor Paver 5-15...
Take care when working with the Leeboy uses a leak-detection dye that hydraulic system to ensure it is completely clean. may turn the hydraulic oil a slight yellow tint. Never allow the hydraulic oil level to fall too low.
Figure 5-17. Battery and Master Battery Switch any problem noted has been corrected. Locations ALWAYS turn the master battery switch off when working on the electrical system or welding anywhere on the machine. Damage to electrical components could result. LeeBoy 6150 Conveyor Paver 5-17...
• Never disconnect the alternator while machine is operating. • Ensure wiring is properly connected before connecting the battery. • Always connect a booster battery in the proper polarity: negative (-) to negative (-) and positive (+) to positive (+). 5-18 LeeBoy 6150 Conveyor Paver...
If the voltage is lower, make certain the generator is turning the correct speed by testing with a Hz meter or photo tachometer. If the voltage is still low, contact your authorized LeeBoy dealer for generator speed tuning (see next section). 5-20...
Maintenance Tires The 6150 Conveyor Paver is a wheeled paver equipped with front (steering) “bogie” rubber tires and rear (drive) heavy-duty, liquid ballast tires. The rear tires should be maintained at 80 - 90 PSI. The front tires are molded onto the wheel and do not require service.
Consult your tire manufacturer (or ballast product manufacturer) for proper ballasting inflation calculations and values. (You may also need to purchase a water filler attachment.) 5-22 LeeBoy 6150 Conveyor Paver...
• If using any of the toxic solutions previously discussed, be sure to dispose of liquid ballast in 6. Repeat on the other front tire. compliance with local and federal environmental laws. Never pump toxic chemicals onto the ground. LeeBoy 6150 Conveyor Paver 5-23...
4. Remove the upper and lower hoses by loosening the hose clamps on each. 5. Disconnect hoses and inspect for damage. • If clamps are not damaged, retain to reinstall. Replace if damaged. 6. Install new hoses and reconnect with hose clamps. 5-24 LeeBoy 6150 Conveyor Paver...
4. Slide new or repaired drive motor into slide mount. 5. Secure with four bolts. 6. Reconnect hydraulic hoses to motor. Adjuster Check for leaks. Bolts Conveyor Motors Chain Sprocket Shaft (Inside Tubing) Main Chains Figure 5-27. Conveyor Components LeeBoy 6150 Conveyor Paver 5-25...
20. Place grating back on over auger. 21. Operate augers and make sure everything is correct. NOTE: Auger chains can be lubricated each day by spraying oil or chain lube through the slots where auger motor is adjusted. 5-26 LeeBoy 6150 Conveyor Paver...
10. Hold the sprocket at the chain as you slide out the motor. Figure 5-32. Under Auger Material Cut-Offs 11. Remove the sprocket from the chain. 12. Slide off the sprocket and remove the auger motor mount. 13. Place the new auger motor onto the mount. LeeBoy 6150 Conveyor Paver 5-27...
9. Reinstall the endgate and tilt screw. NOTE: If equipped with electric screed heat option, remove all wiring and heating elements. Adjuster Adjuster Hinge Shield Bolts Hinge Shield Pivot Pin Shoulder Bolt and Nut Figure 5-36. Wear Plate Replacement LeeBoy 6150 Conveyor Paver 5-29...
Page 118
5-37 and 5-38). Both are easily reached via the right access panel. The auxiliary gear pump is easier to access from the front access panel inside the hopper. Tandem Gear Pump Figure 5-38. Tandem Gear Pump 5-30 LeeBoy 6150 Conveyor Paver...
11. Check for any leaks. running. DO NOT use your bare hands when checking for hydraulic leaks as serious injury can result from an oil leak under high pressure. Always wear safety glasses and protective clothing. LeeBoy 6150 Conveyor Paver 5-31...
DO NOT MAKE MODIFICATIONS TO THE MACHINE. ONLY weld if needed for repair purposes. Weldment modifications to the machine can void your warranty. 5-32 LeeBoy 6150 Conveyor Paver...
• Retighten the bleeder valve. preset intervals. If the overload reaches a dangerous level, the red LED will become solid and you must switch the power off and start the pump again. 5-34 LeeBoy 6150 Conveyor Paver...
To check pressure: Connect the appropriate gauge to the port being tested. (FIgure 5-46) 2. Start the engine, then check gauge for the proper pressure reading. 3. If adjustment is needed, contact your authorized LeeBoy service center. 5-36 LeeBoy 6150 Conveyor Paver...
Maintenance Troubleshooting Chart The troubleshooting chart below identifies the most Contact your authorized LeeBoy dealer for assistance, common symptoms of mechanical problems. Fault service or repair. codes are also shown on the PV480 Digital Display unit on the Operator Control Panel.
Page 126
Check oil cooler and thermostat. Low level in hydraulic tank. Refill to proper level. Clogged filters. Replace filters. Hydraulic pump cavitation or lost power. Suction hose loose. Retighten. Charge pump worn. Rebuild or replace charge pump. 5-38 LeeBoy 6150 Conveyor Paver...
Page 127
HEAT ON Indicator light bulb. Replace the HEAT ON indicator light bulb. light isn’t illuminated. Elements have been tested, Faulty element wiring. Inspect and test element wiring. but the breaker still trips. LeeBoy 6150 Conveyor Paver 5-39...
Engine power drops.) Diagnostic counter = zero Barometric pressure sen- (Default value is set in consideration Barometric voltage 1.6V or less. sor error: Low with high altitude usage. Engine power drops.) 5-40 LeeBoy 6150 Conveyor Paver...
Page 129
MAF sensor: High built-in MAF sensor voltage: 4.9V or more. Ground short circuit of sensor/har- Intake air temperature ness. Intake air temperature built-in Diagnostic counter = zero built-in MAF sensor: Low MAF sensor voltage: 0.1V or less. LeeBoy 6150 Conveyor Paver 5-41...
Page 130
Open circuit of harness/ Open circuit of harness or injector coil. coil in 3rd cylinder injec- Engine vibration increases. Injectors Key switch turn OFF. tor. that have no error are operated. 5-42 LeeBoy 6150 Conveyor Paver...
Page 131
Key switch turn OFF. sensor 1: High sensor voltage 4.92V or more. Ground short circuit of sensor/har- Exhaust gas temperature 3242 ness. DPF inlet temperature sensor Key switch turn OFF. sensor 1: Low voltage 0.08V or less. LeeBoy 6150 Conveyor Paver 5-43...
Page 132
Key switch turn OFF. Emergency exhaust gas DOC inlet temperature 1292° F (700° Inhibit starter relay activation until 4765 temperature sensor 0: C) or more. Engine stops. exhaust temperature reduces down to High 527° F (300° C). 5-44 LeeBoy 6150 Conveyor Paver...
Page 133
Estimated temperature is 113° F (45° 523537 Diagnostic counter = zero ture error. C) or above. EGR stops. QR data read error from EEPROM. 523538 QR data error. Key switch turn OFF. Nozzle correction is not executed. LeeBoy 6150 Conveyor Paver 5-45...
Page 134
Key switch turn OFF. ceived via CAN. EGR stops. EGR (DC motor) temperature error 523576 EGR (DC motor) overheat. signal received via CAN (exceeds Key switch turn OFF. 257° F or 125° C). EGR stops. 5-46 LeeBoy 6150 Conveyor Paver...
Page 135
CAN ETC5 frame time-out error. Key switch turn OFF. frame error. No request to “TSC1 buffer” continues 523596 CAN TSC1 frame error. three times after over-ride control Diagnostic counter = zero request (other than 0x00). LeeBoy 6150 Conveyor Paver 5-47...
Figure 5-49. Terminal Seat the red retaining clip and slide away from the wires. Reinstall connector on to the PV480 panel, making (Figure 5-48) sure the connector shell locks into its mate on the display panel. 5-48 LeeBoy 6150 Conveyor Paver...
RUN again to regain control. If none of these procedures correct the problem, These faults will also prevent machine movement: contact your authorized LeeBoy dealer for assistance. • Steering control box not detected. • Joysticks not optimized. • Pump control coil fault.
MAIN GROUND SLOPE DN WAIT TO START START ENGINE ENABLE WATER IN FUEL GENERATOR CUTOFF CLOSE CUTOFF OPEN DOWN LH AUGER AUTO ALARM FUEL SENDER PILE HEIGHT OUT IGN PWR Figure 6-1. Main Harness (1 of 8) LeeBoy 8515E Conveyor Paver...
Schematics MAIN HARNESS (2 OF 8) Schematic for Part # 1016315 SHOWN FOR INFORMATION RIGHT STEER HORN LEFT STEER LT TOW PROPEL CONTROLLER RT TOW Figure 6-2. Main Harness (2 of 8) LeeBoy 8515E Conveyor Paver...
LH TOPCON SW PWR LH PILE HEIGHT OUT SCREED HEAT POWER GRNWHT HOPPER OUT HOPPER IN LH TOW UP LH TOW DOWN RH TOW UP RH TOW DOWN LT BLU BEACON POSITRAC Figure 6-4. Main Harness (4 of 8) LeeBoy 8515E Conveyor Paver...
UPPER SCREED FLOAT MANIFOLD GROUND LH CUTOFF OPEN RH CUTOFF OPEN LH SLOPE UP RH SLOPE UP HOPPER IN LOWER MANIFOLD LH AUGER RH AUGER GROUND AC DETECTOR Figure 6-5. Main Harness (5 of 8) LeeBoy 8515E Conveyor Paver 6-11...
WATER IN FUEL SHIELD CAN SHIELD ENGINE ENABLE MAIN POWER START MAIN GROUND WAIT TO START START ENGINE ENABLE WATER IN FUEL GENERATOR DOWN FUEL SENDER IGN PWR Figure 6-6. Main Harness (6 of 8) LeeBoy 8515E Conveyor Paver 6-13...
CUTOFF CLOSE CUTOFF OPEN RH AUGER AUTO PILE HEIGHT OUT SLOPE UP AUGER IN AUGER OUT SLOPE DN CUTOFF CLOSE CUTOFF OPEN LH AUGER AUTO PILE HEIGHT OUT Figure 6-7. Main Harness (7 of 8) LeeBoy 8515E Conveyor Paver 6-15...
Schematics CONTROL BOX ASSEMBLY (1 OF 3) Schematic for Part # 1016034 ITEM PART DESCRIPTION NUMBER Figure 6-9. Control Box Assembly (1 of 3) LeeBoy 8515E Conveyor Paver 6-19...
C4 DASH TO PEDESTAL JUMPER HARNESS Schematic for Part # 1016263 COLOR FUNCTION HOPPER OUT HOPPER IN LH TOW UP LH TOW DN RH TOW UP RH TOW DN LT BLU POSITRAC Figure 6-12. C4 Dash to Pedestal Jumper Harness LeeBoy 8515E Conveyor Paver 6-25...
Schematics ELECTRONIC STEERING CORD Schematic for Part # 1016635 4; BLACK 1; BROWN 3; BLUE 2; WHITE Figure 6-16. Electronic Steering Cord LeeBoy 8515E Conveyor Paver 6-33...
POWER AUGER IN AUGER OUT SLOPE LOWER CUTOFF SLOPE CUTOFF CLOSE CUTOFF OPEN AUGER AUG AUTO IN AUG AUTO OUT CUTOFF LIGHT LIGHT PILE HEIGHT POT Figure 6-17. Screed 4-Switch Control Box Assembly - Left LeeBoy 8515E Conveyor Paver 6-35...
AUGER IN AUGER OUT SLOPE LOWER CUTOFF CUTOFF CLOSE SLOPE CUTOFF OPEN GROUND AUG AUTO IN AUTO AUG OUT SLOPE AUGER CUTOFF PILE HEIGHT POT LIGHT LIGHT Figure 6-18. Screed 4-Switch Control Box Assembly - Right LeeBoy 8515E Conveyor Paver 6-37...
Schematics SCREED HEAT CONTROL BOX ASSEMBLY (1 OF 2) Schematic for Part # 1016891 1016901 Figure 6-19. Screed Heat Control Box Assembly (1 of 2) LeeBoy 8515E Conveyor Paver 6-39...
Schematics SCREED HEAT CONTROL BOX ASSEMBLY (2 OF 2) Schematic for Part # 1016891 Figure 6-20. Screed Heat Control Box Assembly (2 of 2) LeeBoy 8515E Conveyor Paver 6-41...
BATT ISO SW OPEN SIDE IGN PWR TEMP SWITCH SPADE TERMINAL ADD LOOM BATT NEG TERMINAL TERMINAL LB PT NO FOR FUSE HOLDER BATT ISO SW OPEN SIDE IGN PWR Figure 6-23. Lower Manifold Harness LeeBoy 8515E Conveyor Paver 6-47...
Fuse Block, ATC 685060 Berm Main Ext. HE (2) 1015936 Berm Ext. Heating Element (2) 1015918 Breaker, 10A 986546 Specifications and designs may change without prior notice. These illustrations do not necessarily show the standard versions. LeeBoy 6150 Conveyor Paver...
Illustrated Parts List REAR DRIVE ASSEMBLY 17,16 15,16 HECK OIL RY 30 DAYS REVIS AR EL ACEITE DA 30 DIAS VÉRIFIER L E NIVEAU D’HUILE TOUS LES 30 JOURS 856456 15,16 Figure 7-1. Rear Drive Assembly LeeBoy 6150 Conveyor Paver...
Illustrated Parts List REAR AUGER ASSEMBLY (1 OF 2) 52,53 54,55,56 4,5,6,7 8,9,10 26,16,27 12,5 15,16,17 46,37,38 7,40,5,4 43,44 36,37 GREASE 38,39 34,6 DAILY 48,5,40 48,5,40 47,5,40 Figure 7-8. Rear Auger Assembly (1 of 2) 7-20 LeeBoy 6150 Conveyor Paver...
Page 215
Includes Items 28-33 851645 Auger Shaft Collar 1017379 Set Screw, 3/8-16 x .75 Knurl Cup Point 810070 Bushing, 2.00 ID x 2.50 OD x 2.50 113-4-28-8 Set Screw, Hex Socket, Cup, 1/4-28 x .50 855313SRV Corner Plate LeeBoy 6150 Conveyor Paver 7-21...
Illustrated Parts List ENGINE ASSEMBLY - RADIATOR 13,14,15 21,22 Figure 7-11. Engine Assembly - Radiator 7-28 LeeBoy 6150 Conveyor Paver...
Page 223
986537-17 Front Motor Mount - Right 986537-16 Front Motor Mount - Left 988673-14 Rear Motor Mount 986537-14 Isolator 100-8-13-24-8 CSHH, 1/2-13 x 1.50, GR8 986810 Washer, Lock, 1/2, Nord Wedge 1017061 Washer, Triangle Engine Mount LeeBoy 6150 Conveyor Paver 7-29...
Illustrated Parts List HOODS AND COVERS - RIGHT 18,19,20 30,22,23 18,19,20 28,19,20 18,19,20 18,19,20 18,19,20 18,19,20 18,19,20 21,22,23 26,22,23,27 18,19,20,24 Figure 7-17. Hoods and Covers - Right 7-40 LeeBoy 6150 Conveyor Paver...
Page 235
CSFHS, 5/16-18 x 1.25, FT 100-6-16-32-5 CSHH, 3/8-16 x 2.00, GR5 987021 Mounting Tab 100-5-18-12-5F CSHH, 5/16-18 x .75, GR5, FT 120-6-16 Wing Screw, Type C, 3/8-16 x 1.00, Cup 100-6-24-16-5F CSHH, 3/8-24 x 1.00, GR5, FT LeeBoy 6150 Conveyor Paver 7-41...
Bleeder the bleeder valve screw 5,6,7 Valve inside of the cut out Screw until the pump primes, then tighten the bleeder valve screw. 1016094 23,24,17 15,16,17,18 15,16 17,18 27 28 Figure 7-18. Spray Down 7-42 LeeBoy 6150 Conveyor Paver...
Page 237
CSHH, 5/16-18 x 1.00, GR5, FT 301-5 Washer, Flat, USS, 5/16 2404-6-6 Connector Adapter, -6 JIC / -6 NPTF 480160 Ball Valve, 3/8 1404-6-6 Union to Male Pipe Adapter, -6 NPTF 5500-6-6 Elbow Adapter, 90°, -6 NPTF / -6 NPTF LeeBoy 6150 Conveyor Paver 7-43...
Illustrated Parts List TOW POINT ASSEMBLY 17,18,19,20 8,3,4 THICKER 26,27,7 8,3,4 THINNER 1016796 8,3,4 9,10,11 2,3,4 Figure 7-19. Tow Point Assembly 7-44 LeeBoy 6150 Conveyor Paver...
Page 239
Screed Arm Actuator Mount - Left (2) Left, (2) Right 1016119 Screed Arm Actuator Mount - Right (2) Left, (2) Right 20961769 Spacer (1) Left, (1) Right 20961736 100-12-10-36-5 CSHH, 3/4-10 x 2.25, GR5 302-12 Washer, Lock, 3/4 LeeBoy 6150 Conveyor Paver 7-45...
DASH ASSEMBLY - CONTROLS FORWARD CAUTION WHEN STEERING PAVER WITH OTHER CONTROL MODULE, THIS RUN/STOP REVERSE SWITCH MUST BE IN THE STOP POSITION. STOP 1000708-02 22,23,19 18,19 11,12,13 20,12,21,13 14,15,16,17 22,23,19 Figure 7-24. Dash Assembly - Controls 7-54 LeeBoy 6150 Conveyor Paver...
Page 249
Nut, Lock, Stover, 1/4-20, GR5 100-5-18-16-5F CSHH, 5/16-18 x 1.00, GR5, FT 300-5 Washer, Flat, SAE, 5/16 100-6-16-26-5 CSHH, 3/8-16 x 1.625, GR5 1007338 Vandalism Cover Spacer 100-5-18-12-5F CSHH, 5/16-18 x .75, GR5, FT 302-5 Washer, Lock, 5/16 LeeBoy 6150 Conveyor Paver 7-55...
1016264 Jumper C3 Dash To Pedestal Harness Not Shown 1016682 Hydraulic Cooler Harness Not Shown 1016537 Generator Valve Adapter Harness Not Shown 1008877 Jumper Heater Element Harness Not Shown 1017986 Power Crown Harness Not Shown LeeBoy 6150 Conveyor Paver 7-61...
Illustrated Parts List SCREED SLIDE PLATE ASSEMBLY - STANDARD RIGHT REAR OF MACHINE LEFT Figure 7-32. Screed Slide Plate Assembly - Standard 7-72 LeeBoy 6150 Conveyor Paver...
Page 267
Screed Slide Plate Assembly - Standard Item Part Number Description Remarks 1002186 Slide w/Shaft Assembly Includes 2-5 1002181 Slide Assembly - No Shafts Includes 3,4 988588 Fiber Bushing 851256 Snap Ring 988601 Screed Extension Shaft - Chrome Finish LeeBoy 6150 Conveyor Paver 7-73...
Illustrated Parts List SCREED PULL ARM - LEFT LEFT EXTENSION 7,8,9 RAISE OPEN LOWER CLOSE LEFT AUGER #1016247 4,5,6 Figure 7-33. Screed Pull Arm - Left 7-74 LeeBoy 6150 Conveyor Paver...
Illustrated Parts List SCREED PULL ARM - RIGHT RIGHT EXTENSION 7,8,9 OPEN RAISE CLOSE LOWER RIGHT AUGER #1016248 4,5,6 Figure 7-34. Screed Pull Arm - Right 7-76 LeeBoy 6150 Conveyor Paver...
Illustrated Parts List SCREED ENDGATES - STANDARD LEFT 11,12 RIGHT Figure 7-36. Screed Endgates- Standard 7-80 LeeBoy 6150 Conveyor Paver...
Page 275
100-8-13-12-5F CSHH, 1/2-13 x .75, GR5, FT 302-8 Washer, Lock, 1/2 870276 Hand Grip 982796 Ultrasonic Power Cable 982795 Ultra Sonic Remote Pod 983050 Coil Cord, 6s/6s 1.5 to 7.5 FT 982794 Ultra Sonic Sensor LeeBoy 6150 Conveyor Paver 7-81...
Illustrated Parts List OPTION - ELECTRIC SCREED EXTENSIONS, NON-SLOPING RIGHT EXTENSION LEFT EXTENSION 11,12, 13,14,15 16,17 Figure 7-43. Option - Electric Screed Extensions, Non-Sloping 7-96 LeeBoy 6150 Conveyor Paver...
Illustrated Parts List OPTION - ELECTRIC SCREED CONTROL ASSEMBLY 19,20,21 LEFT ENDGATE RIGHT ENDGATE HEAT HEAT 1011180 Figure 7-45. Option - Electric Screed Control Assembly 7-100 LeeBoy 6150 Conveyor Paver...
Page 295
985138-04 Terminal Block w/Cover 985141 Relay, 12VDC, DSPT, 25A, N/O 100-4-20-12-5F CSHH, 1/4-20 x .75, GR5, FT 302-4 Washer, Lock, 1/4 200-4-20-5 Nut, Hex, 1/4-20, GR5 1016723 Load Control Box to Bulkhead Harness Not Shown LeeBoy 6150 Conveyor Paver 7-101...
Illustrated Parts List OPTION - HD SCREED OVERVIEW, SLOPING AND NON-SLOPING Figure 7-48. Option - HD Screed Overview, Sloping and Non-Sloping 7-106 LeeBoy 6150 Conveyor Paver...
Page 301
Screed Vibrator - Right 7-50 Manual Turnbuckle Assembly - Non-Slope 7-50 Hydraulic Cylinders - Slope 7-37 Grip Strut Walkboard Assembly - Left 7-37 Grip Strut Walkboard Assembly - Right 7-55 HD Screed Citrus Tank 7-45 Screed Control Assembly LeeBoy 6150 Conveyor Paver 7-107...
Illustrated Parts List OPTION - HD SCREED FRAME ASSEMBLY (2 OF 2) Figure 7-50. Option - HD Screed Frame Assembly (2 of 2) 7-110 LeeBoy 6150 Conveyor Paver...
Page 305
Hydraulic Cylinder, 2.75 x 2.00 x 1.125 Rod Option - Hydraulic Slope 1007212 Group - Mechanical Crown 1009439 Crown & Valley Assembly 1009440 Crown & Valley Turnbuckle Assembly 1006419 Crown Mounting Spacer 1008047 Roller Chain, 60H x 39P w/Half-Link & Masterlink LeeBoy 6150 Conveyor Paver 7-111...
Illustrated Parts List OPTION - HD SCREED SLIDE PLATE ASSEMBLY Figure 7-53. Option - HD Screed Slide Plate Assembly 7-116 LeeBoy 6150 Conveyor Paver...
Page 311
HD Slide w/o Shaft Assembly (1) Per Assembly 1006417 Fiber Bushing, 2.00 ID x 2.25 OD (4) Per Assembly 980380 Spiral Internal Spring, 2.00 ID Shaft (4) Per Assembly 1006415 HD Chromed Screed Extension Shaft (2) Per Assembly LeeBoy 6150 Conveyor Paver 7-117...
Illustrated Parts List OPTION - HD SCREED CITRUS TANK 1,12 5,6,7 Figure 7-55. Option - HD Screed Citrus Tank 7-120 LeeBoy 6150 Conveyor Paver...
Page 315
Straight Fitting, 06MP-06FPX 853211085 90° Fitting, 06MP-06MP 1017163 Group - Citrus Tank for Berm Option Includes 1 and Mount Plates 1016825 Selector Valve Mounting Plate Welded to Item 12 989656 6 Way Electric Selector Valve LeeBoy 6150 Conveyor Paver 7-121...
Illustrated Parts List OPTION - HD BERM SCREED OVERVIEW Sloping and Non-Sloping Figure 7-56. Option - HD Berm Screed Overview, Sloping and Non-Sloping 7-122 LeeBoy 6150 Conveyor Paver...
Illustrated Parts List OPTION - HD 3:1 DEPTH SCREWS (1 OF 2) 2,3,4 13,14,15 16,17,18 21,18,22 29,30,31,32 RIGHT HAND 46,47 LEFT HAND Figure 7-60. Option - HD 3:1 Depth Screws (1 of 2) 7-134 LeeBoy 6150 Conveyor Paver...
Page 329
Washer, Lock, 5/8 (4) Per Assembly 200-10-11-5 Nut, Lock, 5/8-11, GR5 (4) Per Assembly 810110 Push Roller Bearing, 1.250 (3) Per Assembly 1014931 Planetary Threaded Rod (4) Per Assembly 1014921 Planetary Drive Reduction Box (1) Per Assembly LeeBoy 6150 Conveyor Paver 7-135...
Illustrated Parts List OPTION - HD 3:1 DEPTH SCREWS (2 OF 2) 2,3,4 13,14,15 16,17,18 21,18,22 29,30,31,32 RIGHT HAND 46,47 LEFT HAND Figure 7-60. Option - HD 3:1 Depth Screws (2 of 2) 7-136 LeeBoy 6150 Conveyor Paver...
Page 331
Universal Joint Bearing As Needed 1006431 Adjuster Screw (1) Per Assembly 1006429 Adjuster Sleeve w/Ball Joint (1) Per Assembly 100-12-10-36-5 CSHH, 3/4-10 x 2.25, GR5 (1) Per Assembly 302-12 Washer, Lock, 3/4 (1) Per Assembly LeeBoy 6150 Conveyor Paver 7-137...
Illustrated Parts List OPTION - HD SCREED HEATED ENDGATES 22,11,23 7,11,23 10,11 Figure 7-61. Option - HD Screed Heated Endgates 7-138 LeeBoy 6150 Conveyor Paver...
Page 333
(1) Per Assembly 920070 Thumb Screw, 3/8-16 x 1.00 (1) Per Assembly 1008905 Sonic Sensor Mount (1) Per Assembly 100-6-16-12-5F CSHH, 3/8-16 x .75, GR5, FT (1) Per Assembly 300-6 Washer, Flat, SAE, 3/8 (2) Per Assembly LeeBoy 6150 Conveyor Paver 7-139...
Illustrated Parts List OPTION - HD SCREED HEATED SAFETY EDGE ENDGATES 27,7,28 29,28 14,15,16 17,7 6,7,8 9,10 Figure 7-62. Option - HD Screed Heated Safety Edge Endgates 7-140 LeeBoy 6150 Conveyor Paver...
Page 335
(1) Per Assembly 1008905 Sonic Sensor Mount (1) Per Assembly 100-6-16-12-5F CSHH, 3/8-16 x .75, GR5, FT (1) Per Assembly 300-6 Washer, Flat, SAE, 3/8 (2) Per Assembly 204-6-16-5 Nut, Lock, Stover, 3/8-16, GR5 (1) Per Assembly LeeBoy 6150 Conveyor Paver 7-141...
Illustrated Parts List OPTION - HD MISCELLANEOUS OPTIONS 2,3,4 14,15,16 17,15,16 VALLEY CROWN NOTE: BASED ON 10’ WIDTH 1007677-06 Figure 7-63. Option - HD Miscellaneous Options 7-142 LeeBoy 6150 Conveyor Paver...
Page 337
Power Crown Switch Mounting Plate 99985 Pipe Bushing, 12MP-08FP, Steel 3400DI Water Tight Connector, 3/4" x 3/4" 989656 Electric Selector Valve, 6-Way 1007232 Power Crown Gauge Bar 1007677-06 Decal - Power Crown 1015123 Power Crown Hose Kit Not Shown LeeBoy 6150 Conveyor Paver 7-143...
OPTION - UMBRELLA & FIRE EXTINGUISHERS CAUTION Do not lower umbrella below this arrow. Failure to comply may result in minor or moderate injury. 988207 Rev 1 Figure 7-69. Option - Umbrella & Fire Extinguishers 7-154 LeeBoy 6150 Conveyor Paver...
Page 349
Option - Fire Extinguisher w/Bracket, 5 Lbs. 35828 Fire Extinguisher, 5 Lbs., 3A:40B:C 12313-5DC Mounting Bracket, 5 Lbs. Fire Extinguisher 982031 Option - Fire Extinguisher w/Bracket, 10 Lbs. 1014536 Fire Extinguisher, 10 Lbs., 4A:80B:c 12034-5HD Mounting Bracket, 10 Lbs. Fire Extinguisher LeeBoy 6150 Conveyor Paver 7-155...
STEER RET TEE TO LWR MAN T2 TEE F387TC0606080808-67 LWR MAN T2 TEE TO RET MAN LEFT F387TC0606101010-42 LWR MAN T TO CHARGE FLTR F387TC0639101010-90 FRONT PUMP P TO LWR MAN P2 F387TC0606121212-55-AS-B-19-51 PROPEL PUMP DRN TO RAD BTM 7-156 LeeBoy 6150 Conveyor Paver...
Page 351
LH VIB MTR DRN TO RET MAN LEFT Hose Qty. Part Number Description 1015125 8520 Main Screed Hose Kit 84/85 F387TC0606060606-27-AS-B-13-24 HOSE ASSEMBLY, HYDRAULIC, 3000 PSI, -6FJX/-6FJX, 27” 86/87 F387TC0606060606-80-AS-B-13-77 HOSE ASSEMBLY, HYDRAULIC, 3000 PSI, -6FJX/-6FJX, 80” LeeBoy 6150 Conveyor Paver 7-157...
Page 359
Conveyor Idler Sprocket Weldment 1008923SRV Conveyor Idler Weldment 1008919SRV Conveyor Link w/o Tab 850080A Conveyor Motor Mount 1016028 Conveyor Paddle Pin 1009452 Conveyor Switch Arm 900060 Conveyors Automatic Micro Switch 900050SRV Coolant Recovery Tank 986537-46 7-11 LeeBoy 6150 Conveyor Paver 7-165...
Page 360
CSFHS, 1/4-20 x .75, FT 105-4-20-12-F 7-58 CSFHS, 3/8-16 x 1.50, FT 105-6-16-24-F 7-57 CSFHS, 3/8-16 x 1.50, FT 105-6-16-24-F 7-58 CSFHS, 5/16-18 x 1.25, FT 105-5-18-20-F 7-16 CSFHS, 5/16-18 x 1.25, FT 105-5-18-20-F 7-17 7-166 LeeBoy 6150 Conveyor Paver...
Page 361
CSHH, 1/2-13 x 2.50, GR5 100-8-13-40-5 7-52 CSHH, 1/2-13 x 2.75, GR5 100-8-13-44-5 7-19 CSHH, 1/2-13 x 3.00, GR5 100-8-13-48-5 CSHH, 1/2-20 x 1.00, GR5, FT 100-8-20-16-5F CSHH, 1/2-20 x 1.00, GR5, FT 100-8-20-16-5F 7-42 LeeBoy 6150 Conveyor Paver 7-167...
Page 362
CSHH, 3/8-16 x .75. GR5, FT 100-6-16-12-5F 7-42 CSHH, 3/8-16 x 1.00, GR5 100-6-16-16-5F 7-33 CSHH, 3/8-16 x 1.00, GR5 100-6-16-16-5F 7-34 CSHH, 3/8-16 x 1.00, GR5, FT 100-6-16-16-5F CSHH, 3/8-16 x 1.00, GR5, FT 100-6-16-16-5F 7-168 LeeBoy 6150 Conveyor Paver...
Page 363
CSHH, 3/8-24 x .75, GR5, FT 100-6-24-12-5F 7-42 CSHH, 3/8-24 x .75, GR5, FT 100-6-24-12-5F 7-51 CSHH, 3/8-24 x .75, GR5, FT 100-6-24-12-5F 7-52 CSHH, 3/8-24 x 1.00, GR5, FT 100-6-24-16-5F 7-17 CSHH, 3/8-24 x 1.00, GR5, FT 100-6-24-16-5F 7-30 LeeBoy 6150 Conveyor Paver 7-169...
Page 364
CSHH, 5/8-11 x 1.25, GR5, FT 100-10-11-20-5F 7-67 CSHH, 5/8-11 x 1.25, GR5, FT 100-10-11-20-5F 7-68 CSHH, 5/8-11 x 1.375, GR5, FT 100-10-11-22-5F CSHH, 5/8-11 x 1.50, GR5, FT 100-10-11-24-5F CSHH, 5/8-11 x 1.50, GR5, FT 100-10-11-24-5F 7-29 7-170 LeeBoy 6150 Conveyor Paver...
Page 365
CSSH, 1/2-13 x 1.75, GR8 100-8-13-28-8 7-15 CSSH, 3/8-16 x 1.50, FT 102-6-16-24-F CSSH, 3/8-16 x 2.50 102-6-16-40 CSSH, 5/8-11 x 5.00 102-10-11-80 7-29 CSSH, 5/8-11 x 5.00 102-10-11-80 7-41 CSSH, 5/8-11 x 5.00 102-10-11-80 7-42 LeeBoy 6150 Conveyor Paver 7-171...
Page 374
1016682 7-26 Hydraulic Cylinder w/Sensor, 2.50 x 1.06 x 6.00 1015952 Hydraulic Cylinder, 1.50 x 30.00 x 1.00 Rod 930070 7-68 Hydraulic Cylinder, 1.50B x .75R x 2.50 S 1015953 Hydraulic Cylinder, 1.50Bx.75Rx2.5S 1015953 7-23 7-180 LeeBoy 6150 Conveyor Paver...
Page 375
140030GK 7-10 Hydraulic Tank Access Port 1006804 7-10 Hydraulic Tank Assembly 1016047 7-10 Hydraulic Tank Weldment 1016046 7-10 -I, J, K- Ignition Key 982008-04 7-26 Ignition Switch 39146-14 7-26 Indicator Light - White 1010500 7-26 LeeBoy 6150 Conveyor Paver 7-181...
Page 376
980460 7-16 Lever Latch 980460 7-17 Linear Actuator Rod End 851212 7-19 Linear Actuator, 12V, 6.00" 851518 7-19 Load Control Box to Bulkhead Harness 1016723 7-45 Lock Nut, PTORQ, 3/4-16 95998936 7-35 Lock Pin 1013877 7-182 LeeBoy 6150 Conveyor Paver...
Page 377
7-26 Main Heat Box Assembly - Left 1017683SRV 7-57 Main Heat Box Assembly - Right 1017682SRV 7-58 Main Heat Box Lid Weldment - Left 1015431 7-57 Main Heat Box Lid Weldment - Right 1015419 7-58 LeeBoy 6150 Conveyor Paver 7-183...
Page 384
Run Tee Adapter, -10 JIC / -12 O-Ring / -10 JIC 6804-10-12-10 NWO 7-15 Run Tee Adapter, -4 JIC / -6 O-Ring / -4 JIC 6804-4-6-4 NWO 7-15 Run Tee Swivel Adapter, -10 JIC / -10 JIC / -10 JIC 6602-10-10-10 7-22 7-190 LeeBoy 6150 Conveyor Paver...
Page 385
Screed Ctirus Tank Assembly - Standard Electric 1008356SRV 7-38 Screed Elements Cover 1011697 7-29 Screed Elements Cover 1011697 7-41 Screed Elements Cover 1011697 7-42 Screed Extension Adjuster Assembly 851185SRV 7-43 Screed Extension Adjuster Assembly 851185SRV 7-44 LeeBoy 6150 Conveyor Paver 7-191...
Page 386
Set Screw, HSKT, Cup, 3/8-16 x .375 113-6-16-6 7-60 Set Screw, HSKT, Cup, 3/8-16 x .75 113-6-16-12 7-61 Set Screw, HSKT, Cup, 3/8-16 x .75 113-6-16-12 7-62 Shaft Seal, 1.25 ID x 2.00 OD 1014930 7-60 7-192 LeeBoy 6150 Conveyor Paver...
Page 387
1015380 7-61 Sonic Sensor Bracket Weldment 1015380 7-62 Sonic Sensor Mount 1008905 7-54 Sonic Sensor Mount 1008905 7-61 Sonic Sensor Mount 1008905 7-62 Sonic Tracker II Assembly 1010499-06 7-66 Sonic Tracker II Assembly 1010499-06 7-67 LeeBoy 6150 Conveyor Paver 7-193...
Page 398
Wear Plate w/Studs, 3/8” 1016475 7-50 Wedge Connector Plug, 3 Pin 983210 7-26 Wedgelock Connector, W3P 983211 7-26 Wing Screw, Type C, 3/8-16 x 1.00, Cup 120-6-16 7-17 Wing Screw, Type C, 3/8-16 x 1.00, Cup 120-6-16 7-24 7-204 LeeBoy 6150 Conveyor Paver...
Page 400
500 Lincoln County Parkway Ext. Lincolnton, North Carolina 28092 Phone: (704) 966-3300 - Fax Sales: (704) 483-5802 www.LeeBoy.com Printed in the U.S.A.