Download Print this page

Jehnert 45180 Installation Instructions Manual

Doorboards with 3-way soundsystem for audi a3 8p sportback

Advertisement

Quick Links

Installation Instructions Product-Ident: 45180
doorboards include speakers, Audi A3 8P Sportback
Technical Details:
Car Features:
Model/Year:
Setup-Advice:
recommended amplifier power:
Parts list:
1x
Doorboards (right+left) Audi A3 8P Sportback, covered
1x
grills (right+left) Audi a3 8p sportback , cover: acoustic fabric
2x
XE 26 - Neodymium-Tweeter ø 26mm (1 ") incl. mounting device, Hex nut M4, washer ø 12mm
2x
XM 110 - High-End-midrange driver, ø 100mm (4 "), incl. adapter ring
4x
XM 165 - Low midrange driver, power woofer ø 165mm (6,5 ")
1x
3-way frequency crossover (right+left) Audi A3 -sportback - part-no. 45180
1x
Hardware bag, Audi A3 -sportback - part-no. 45180/41180
2x
2x
2x
16x
6x
4x
12x
12x
Garantee:
We grant a manufacturers guarantee of 2 years starting from the date of purchase of the doorboard or sound system from the dealer. Within this
guarantee period to our choice we either repair or replace free of charge all defects due to material or workmanship. Exempt from this guarantee
are damages due to improper use, wear and tear or damages which have to be led back on wear or interventions by third parties. The guarantee
does not cover subsequent damages or such defects that only insignificantly impair the value or the usability of the doorboard/sound system. The
guarantee does not cover damages due to external influences. Doorboards with additional or wrong assembly drill holes cannot be returned. These
are damages to the doorboard which cannot be repaired again.
4-doors, electrical window controls
8PA (09.2004)
To reach the best performance, the setup of the
radio (Bass, Loudness etc.) should be null or
neutral.
from 2x 100 - 200 Watt / 2 Ohm
flat head srew M4 x 40
flat head srew M4 x 50
flat head srew M4 x 60
hex nut M4
spax screw 4,5 x 80
Velcro strip à 2,5 cm (reserve)
washer 12mm
washer 20mm
08.10.09 10:23
Seite 1 von 8

Advertisement

loading

Summary of Contents for Jehnert 45180

  • Page 1 XM 110 - High-End-midrange driver, ø 100mm (4 "), incl. adapter ring XM 165 - Low midrange driver, power woofer ø 165mm (6,5 ") 3-way frequency crossover (right+left) Audi A3 -sportback - part-no. 45180 Hardware bag, Audi A3 -sportback - part-no. 45180/41180...
  • Page 2 In order to avoid vibration noise insulate all cables with insulating tape e.g. 2.4 Adjust the JEHNERT-tweeter in the original cut-out and affix with hot melt adhesive or silicone on the backside. 2.5 Reinstall the A-pillar.
  • Page 3 08.10.09 10:23 Installation Instructions Product-Ident: 45180 3 Handling of door card: Doorboard alignment 3.1 Place the door card on a plane surface. 3.2 Dismount the loudspeakers attached to the doorboard for transport protection --> retain the screws for later assembly.
  • Page 4 08.10.09 10:23 Installation Instructions Product-Ident: 45180 5 Marking fastening points 5.1 Mark the fixing points 1-5_ premounted in the doorboard: Pressing the doorboard onto the door card leaves a visible impression of the screws - the fastening positions of the door card.
  • Page 5 08.10.09 10:23 Installation Instructions Product-Ident: 45180 7 Fastening doorboard 7.1 Screw in the screws supplied with. Affix the doorboard to the door card. Screw all screws only hand-tight . Secure all M4-screws with washers and nuts. TIP: Treat the screw thread with a liquid for screw-in type fuse. (Speaker vibrations may loosen the screws after some time).
  • Page 6 08.10.09 10:23 Installation Instructions Product-Ident: 45180 8 Adaptation amplifier - crossover circuit / Insulation of the car doors Insulation of the car doors - Important tips against vibration-noise (see attached installation recommendation) 8.2 Adaptation amplifier - crossover circuit: Lead 1x speaker cable (1,5 - 4 qmm) from amplifier to the crossover circuit:...
  • Page 7 08.10.09 10:23 Installation Instructions Product-Ident: 45180 10 Installation of crossover circuit + speaker connection 10.1 Precable crossovers - see wiring diagram. 10.2 Install crossover – without housing; covered with foamed material - in the hollow space between door card and car door (see fig.) and ensure precise fit.
  • Page 8 08.10.09 10:23 Installation Instructions Product-Ident: 45180 11 Installation of the door card onto the car doors 11.1 Check up length of the screws and bolts: In order to prevent damages of mechanic parts of the car doors, please check once again the length of all bolts and screws on the...
  • Page 9 Insulation of the door lining Attention / Danger !!! No insulation behind the side-airbags (fi g. “B”) ☞ Important: No insulation material behind - loudspeaker - door latch lever - drill ahole for the installation clip (fi g. A) fi g.: example of a car door Important tip: the use of woofer in the door lining may cause vibrations which lead to annoying rattle noises in the car door Preventive measurements against vibration noise: •...
  • Page 10 Installation of the speaker’s grill Precisely align and carefully press grill into the Velcro fasteners. ☞ The Velcro fastener makes a crackling sound when it is closed correctly. Our Tip: If the panel cannot be pressed on completely at some points. . . Cause: the special form at these points and the resulting differences inmaterial cross section of the grill.