Advertisement
Quick Links
Installation Instructions Product-Ident: 75181
Doorboards include speakers, Audi A3 8P - 2-türig
Technical Details:
Car Features:
Model/Year:
Door Dampening:
Setup-Advice:
recommended amplifier power:
Metal cutting:
Parts list:
1x
Doorboards (right+left) Audi A3 8P, covered
1x
grills (right+left) Audi A3 8P, cover: acoustic fabric
2x
XE 26 - Neodymium-Tweeter ø 26mm (1") incl. mounting device, Hex nut M4, washer ø 12mm
2x
XM 110 - High-End-midrange driver, ø 100mm (4"), incl. adapterring
8x
XM 165 - Low midrange driver, power woofer ø 165mm (6,5")
1x
serial wire set for woofers (right + left)
2x
3-way frequency crossover (right+left) Audi A3 -2-door only - part-no. 75181
1x
Hardware bag, Audi A3 -2-door only - part-no. 75181/71181
8x
2x
2x
22x
4x
4x
18x
Garantee:
We grant a manufacturers guarantee of 2 years starting from the date of purchase of the doorboard or sound system from the dealer. Within this
guarantee period to our choice we either repair or replace free of charge all defects due to material or workmanship. Exempt from this guarantee
are damages due to improper use, wear and tear or damages which have to be led back on wear or interventions by third parties. The guarantee
does not cover subsequent damages or such defects that only insignificantly impair the value or the usability of the doorboard/sound system. The
guarantee does not cover damages due to external influences. Doorboards with additional or wrong assembly drill holes cannot be returned. These
are damages to the doorboard which cannot be repaired again.
electrical window controls, only 2-doors
8P (05.2003)
recommended - see attached installation
recommendation
To reach the best performance, the setup of the
radio (Bass, Loudness etc.) should be null or
neutral.
from 2x 150 - 300 Watt / 4 Ohm
not applicable
flat head srew M4 x 30
flat head srew M4 x 40
flat head srew M4 x 50
hex nut M4
Velcro strip à 2,5 cm (reserve)
washer 12mm
washer 20mm
Advertisement
Related Manuals for Jehnert 75181
Summary of Contents for Jehnert 75181
- Page 1 XM 165 - Low midrange driver, power woofer ø 165mm (6,5") serial wire set for woofers (right + left) 3-way frequency crossover (right+left) Audi A3 -2-door only - part-no. 75181 Hardware bag, Audi A3 -2-door only - part-no. 75181/71181 flat head srew M4 x 30...
- Page 2 2.2 Remove the tweeter out of the mounting holder:--- >bayonet catch: turn to the right and pull out of the holding device (by means of the screw) - no more need of the mounting device) 2.3 Adjust the JEHNERT-tweeter in the original cut-out and affix with hot melt adhesive or silicone on the back side.
- Page 3 Installation Instructions Product-Ident: 75181 3 Handling of the door card: Doorboard alignment 3.1 Place the door card on a plane surface. 3.2 Dismount the loudspeakers attached to the doorboard for transport protection --> retain the screws for later assembly. 3.3 Place the panel without loudspeakers on the door card and align it:...
- Page 4 Installation Instructions Product-Ident: 75181 4 Handling of door card Use the doorboard as template in order to mark fastening points and cut-outs Align the doorboard exactly to the fixing points of the door card. 5 Mark the fixing points 5.1 Mark the fixing points 1-5_ premounted in the doorboard:...
- Page 5 Installation Instructions Product-Ident: 75181 6 Marking of the door card cut-outs The cut out for the speakers are providing the full volume of the car door: 6.1 Draw the midrange cut-out acc. to figure. Please consider overlapping midrange position on the backside of the doorboard, align the doorboard planely and mark the cut outs accordingly.
- Page 6 Installation Instructions Product-Ident: 75181 7 Fastening Doorboard 7.1 Screw in the M4-screws supplied with. Slightly affix the doorboard to the door card. Screw all M4-screws only hand-tight . Secure all screws with washers and nuts. TIP: Treat the screw thread with a liquid for screw-in type fuse. (speaker vibrations may loosen the screws after...
- Page 7 Installation Instructions Product-Ident: 75181 8 Adaptation amplifier - crossover circuit / Insulation of the car doors 8.1 Carefully remove the moisture protection foil. Insulation of the car doors - Important tips against vibration-noise (see attached installation recommendation) 8.3 Adaptation amplifier - crossover circuit:...
- Page 8 Installation Instructions Product-Ident: 75181 10 Mounting crossover circuit + speaker connection 10.1 Precable crossovers - see wiring diagram Verstärker empfohlene Leistung 200-300 Watt RMS / 4 Ohm 10.2 Install crossover in the hollow space between doorboard and door card (see fig.) and connect it with the door metal Position: Between the 2nd and 3rd woofer behind the separating bar of the grills.
- Page 9 Insulation of the door lining Attention / Danger !!! No insulation behind the side-airbags (fi g. “B”) ☞ Important: No insulation material behind - loudspeaker - door latch lever - drill ahole for the installation clip (fi g. A) fi g.: example of a car door Important tip: the use of woofer in the door lining may cause vibrations which lead to annoying rattle noises in the car door Preventive measurements against vibration noise: •...
- Page 10 Installation of the speaker’s grill Precisely align and carefully press grill into the Velcro fasteners. ☞ The Velcro fastener makes a crackling sound when it is closed correctly. Our Tip: If the panel cannot be pressed on completely at some points. . . Cause: the special form at these points and the resulting differences inmaterial cross section of the grill.