Advertisement
Quick Links
Installation Instructions Product-Ident: 75112
doorboards with soundsystem, Golf V, only 2-doors
Technical Details:
Car Features:
Model/Year:
Setup-Advice:
recommended amplifier power:
Parts list:
1x
Doorboards (right+left) VW golf 5 - only 2doors, covered
1x
grills (right+left) VW golf 5- only 2 doors, cover: acoustic fabric
2x
XE 26 - Neodymium-Tweeter ø 26mm (1") incl. mounting device, Hex nut M4, washer ø 12mm
2x
XM 110 - High-End-midrange driver, ø 100mm (4"), incl. adapter ring
8x
XM 165 - Low midrange driver, power woofer ø 165mm (6,5")
1x
serial wire set for woofers (right + left)
1x
3-way frequency crossover (right+left) VW Golf V 2-doors - part.no 75112
1x
Hardware bag, VW Golf V 2-doors - part.no 75112/71112
5x
2x
1x
1x
22x
6x
4x
2x
6x
16x
Garantee:
We grant a manufacturers guarantee of 2 years starting from the date of purchase of the doorboard or sound system from the dealer. Within this
guarantee period to our choice we either repair or replace free of charge all defects due to material or workmanship. Exempt from this guarantee
are damages due to improper use, wear and tear or damages which have to be led back on wear or interventions by third parties. The guarantee
does not cover subsequent damages or such defects that only insignificantly impair the value or the usability of the doorboard/sound system. The
guarantee does not cover damages due to external influences. Doorboards with additional or wrong assembly drill holes cannot be returned. These
are damages to the doorboard which cannot be repaired again.
electrical window controls, only 2-doors
Golf 5 (06.2003)
To reach the best performance, the setup of the
radio (Bass, Loudness etc.) should be null or
neutral.
from 2x 150 - 300 Watt / 4 Ohm
flat head srew M4 x 20
flat head srew M4 x 30
flat head srew M4 x 40
flat head srew M4 x 50
hex nut M4
sheet metal nut 4,2mm
spax screw 5 x 60
spax screw 5 x 70
washer 12mm
washer 20mm
20.09.10 08:29
Seite 1 von 8
Advertisement
Related Manuals for Jehnert 75112
Summary of Contents for Jehnert 75112
- Page 1 XM 165 - Low midrange driver, power woofer ø 165mm (6,5") serial wire set for woofers (right + left) 3-way frequency crossover (right+left) VW Golf V 2-doors - part.no 75112 Hardware bag, VW Golf V 2-doors - part.no 75112/71112 flat head srew M4 x 20...
- Page 2 20.09.10 08:30 Installation Instructions Product-Ident: 75112 1 Disassembly of the door card 1.1 Roll down window completely. 1.2 Unclip the door handle and unscrew the 2 screws underneath (A1 + A2). 1.3 Remove the 3 screws (B1 - B3) on the bottom side of the door card.
- Page 3 20.09.10 08:30 Installation Instructions Product-Ident: 75112 2 Handling of door card: Doorboard alignment 2.1 Place the door card on a plane surface. 2.2 Dismount the loudspeakers attached to the doorboard for transport protection --> retain the screws for later assembly.
- Page 4 20.09.10 08:30 Installation Instructions Product-Ident: 75112 3 Handling of door card 3.1 Use the doorboard as template in order to mark fastening points and cut-outs: Precisely align the doorboard to the fixing points of the door card. 4 Marking fastening points driver's side 4.1 Mark the fixing points 1-6_ premounted in the doorboard:...
- Page 5 20.09.10 08:30 Installation Instructions Product-Ident: 75112 5 Handling of door card cut-outs The cut out behind the speakers are providing the required full volume of the car door: Example 5.1 Mark the cut outs for the woofers on the door card. Enlarge them approx. 1cm (= approx. outer diameter of the woofers) 5.2 For a plane alignment of the doorboard also mark the overlapping tray for the cut-out.
- Page 6 8.2 Adjust the tweeter in the original mounting device. Affix all around with hot melt adhesive or silicone. 8.3 Adapt the JEHNERT-tweeter cable with the speaker cable (1,5-4 qmm) - length of cable up to where the crossover is installed in the doorboard.
- Page 7 20.09.10 08:30 Installation Instructions Product-Ident: 75112 9 Adaptation amplifier - crossover circuit / Insulation of the car doors 9.1 Carefully remove the moisture protection foil. Insulation of the car doors - Important tips against vibration-noise (see attached installation recommendation) 9.3 Adaptation amplifier - crossover circuit:...
- Page 8 20.09.10 08:30 Installation Instructions Product-Ident: 75112 12 Installation of crossover circuit 12.1 Precable crossovers - see wiring diagram. Verstärker empfohlene Leistung 200-300 Watt RMS / 4 Ohm 12.2 Install crossover – without housing; covered with foamed material - in the hollow space between doorboard and door card (see fig.) and ensure precise fit.
- Page 9 Insulation of the door lining Attention / Danger !!! No insulation behind the side-airbags (fi g. “B”) ☞ Important: No insulation material behind - loudspeaker - door latch lever - drill ahole for the installation clip (fi g. A) fi g.: example of a car door Important tip: the use of woofer in the door lining may cause vibrations which lead to annoying rattle noises in the car door Preventive measurements against vibration noise: •...
- Page 10 Installation of the speaker’s grill Precisely align and carefully press grill into the Velcro fasteners. ☞ The Velcro fastener makes a crackling sound when it is closed correctly. Our Tip: If the panel cannot be pressed on completely at some points. . . Cause: the special form at these points and the resulting differences inmaterial cross section of the grill.