Woods BRUSHBULL BB48X Operator's Manual page 8

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
• If this machine is not equipped with full chain,
rubber, or steel band shielding, operation must
be stopped when anyone comes within 300 feet
(92 m).
• This shielding is designed to reduce the risk
of thrown objects. The mower deck and protec-
tive devices cannot prevent all objects from
escaping the blade enclosure in every mowing
condition. It is possible for objects to ricochet
and escape, traveling as much as 300 feet (92 m).
 Never direct discharge toward people, animals,
or property.
 Do not operate or transport equipment while
under the influence of alcohol or drugs.
 Operate only in daylight or good artificial light.
 Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
 Always comply with all state and local lighting
and marking requirements.
 Never allow riders on power unit or attachment.
 Power unit must be equipped with ROPS or
ROPS cab and seat belt. Keep seat belt securely
fastened. Falling off power unit can result in death
from being run over or crushed. Keep foldable
ROPS system in "locked up" position at all times.
 Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt, place transmission in neutral, engage brake,
and ensure all other controls are disengaged
before starting power unit engine.
 Operate tractor PTO at 540 RPM. Do not exceed.
 Do not operate PTO during transport.
 Look down and to the rear and make sure area
is clear before operating in reverse.
 Do not operate or transport on steep slopes.
 Do not stop, start, or change directions sud-
denly on slopes.
 Use extreme care and reduce ground speed on
slopes and rough terrain.
 Watch for hidden hazards on the terrain during
operation.
 Stop power unit and equipment immediately
upon striking an obstruction. Turn off engine,
remove key, inspect, and repair any damage before
resuming operation.
 Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
8 Safety
SAFETY RULES
 Before performing any service or maintenance,
disconnect driveline from tractor PTO.
MAINTENANCE
 Before performing any service or maintenance,
disconnect driveline from tractor PTO.
 Before working underneath, disconnect drive-
line, raise cutter, and block cutter securely. Hydrau-
lic system leak down and failure of mechanical or
hydraulic system can cause equipment to drop.
 Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
 Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
 Make sure attachment is properly secured,
adjusted, and in good operating condition.
 Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
 Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.

Make certain all movement of equipment com-
ponents has stopped before approaching for ser-
vice.
 Frequently check blades. They should be sharp,
free of nicks and cracks, and securely fastened.
 Do not handle blades with bare hands. Careless
or improper handling may result in serious injury.
 Your dealer can supply genuine replacement
blades. Substitute blades may not meet original
equipment specifications and may be dangerous.
 Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
 Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
 Make sure shields and guards are properly
installed and in good condition. Replace if dam-
aged.
Single Spindle Cutter LD/MD (Rev. 10/27/2006)