Advertisement
Quick Links
TECHNICAL PARAMETERS
ＰＤ Ｉ Ｃ５６
ＰＤ Ｉ Ｃ６６
５． ２５＂ ２－Ｗ ａｙ Ｃｅｉ ｌ ｉ ｎｇ Ｓｐｅａｋｅｒ Ｓｙｓｔ ｅｍ
６． ５＂ ２－Ｗ ａｙ Ｃｅｉ ｌ ｉ ｎｇ Ｓｐｅａｋｅｒ Ｓｙｓｔ ｅｍ
＊Ｂｌ ａｃｋ ＰＰ Ｃｏｎｅ Ｗ ｉ ｔ ｈ Ｒｕｂｂｅｒ Ｅｄｇｅ
＊Ｂｌ ａｃｋ ＰＰ Ｃｏｎｅ Ｗ ｉ ｔ ｈ Ｒｕｂｂｅｒ Ｅｄｇｅ
＊１／２＂ Ｔｉ ｔ ａｎｉ ｕｍ Ｄ ｏｍ ｅ Ｔｗ ｅｅｔ ｅｒ Ｉ ｎ Ｓｗ ｉ ｖｅｌ Ｍ ｏｕｎｔ
＊１／２＂ Ｔｉ ｔ ａｎｉ ｕｍ Ｄ ｏｍ ｅ Ｔｗ ｅｅｔ ｅｒ Ｉ ｎ Ｓｗ ｉ ｖｅｌ Ｍ ｏｕｎｔ
＊Ｐｏｗ ｅｒ： １５０ Ｗ ａｔ ｔ ｓ Ｒａｔ ｅｄ Ｐｅａｋ
＊Ｐｏｗ ｅｒ： ２００ Ｗ ａｔ ｔ ｓ Ｒａｔ ｅｄ Ｐｅａｋ
＊Ｆｒｅｑｕｅｎｃｙ Ｒｅｓｐｏｎｓｅ： ８０Ｈ Ｚ－２０ＫＨ Ｚ
＊Ｆｒｅｑｕｅｎｃｙ Ｒｅｓｐｏｎｓｅ： ６０Ｈ Ｚ－２０ＫＨ Ｚ
＊Ｉ ｍ ｐｅｄａｎｃｅ： ８ Ｏ ｈｍ ｓ
＊Ｉ ｍ ｐｅｄａｎｃｅ： ８ Ｏ ｈｍ ｓ
＊Ｓｅｎｓｉ ｔ ｉ ｖｉ ｔ ｙ： ８８ ｄＢ
＊Ｓｅｎｓｉ ｔ ｉ ｖｉ ｔ ｙ： ８９ ｄＢ
＊ｗ ｉ ｔ ｈ Ｅｌ ｅｃｔ ｒｏｎｉ ｃ Ｃｒｏｓｓｏｖｅｒ Ｎ ｅｔ ｗ ｏｒｋ
＊ｗ ｉ ｔ ｈ Ｅｌ ｅｃｔ ｒｏｎｉ ｃ Ｃｒｏｓｓｏｖｅｒ Ｎ ｅｔ ｗ ｏｒｋ
＊Ｓｕｐｐｌ ｉ ｅｄ Ｗ ｉ ｔ ｈ Ｒｏｕｎｄ Ｇ ｒｉ ｌ ｌ ｅｓ Ａ ｎｄ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ
＊Ｓｕｐｐｌ ｉ ｅｄ Ｗ ｉ ｔ ｈ Ｒｏｕｎｄ Ｇ ｒｉ ｌ ｌ ｅｓ Ａ ｎｄ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ
＊Ｓｉ ｚｅ： Ｒｏｕｎｄ ／ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ： ８ "／８ "＊８ "
３
／
１０
／
３
１０
３
／
１０
＊Ｓｉ ｚｅ： Ｒｏｕｎｄ ／ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ： ９ "／９ "＊９ "
＊Ｃｕｔ ｏｕｔ Ｓｉ ｚｅ： ６ "
４
＊Ｃｕｔ ｏｕｔ Ｓｉ ｚｅ： ８"
５ ／
＊Ｍ ｏｕｎｔ ｉ ｎｇ Ｄ ｅｐｔ ｈ： ３"
＊Ｍ ｏｕｎｔ ｉ ｎｇ Ｄ ｅｐｔ ｈ： ３"
ＰＤ Ｉ Ｃ８６
ＰＤ Ｉ Ｃ１０６
８＂ ２－Ｗ ａｙ Ｃｅｉ ｌ ｉ ｎｇ Ｓｐｅａｋｅｒ Ｓｙｓｔ ｅｍ
１０＂ ２－Ｗ ａｙ Ｃｅｉ ｌ ｉ ｎｇ Ｓｐｅａｋｅｒ Ｓｙｓｔ ｅｍ
＊Ｂｌ ａｃｋ ＰＰ Ｃｏｎｅ Ｗ ｉ ｔ ｈ Ｒｕｂｂｅｒ Ｅｄｇｅ
＊Ｂｌ ａｃｋ ＰＰ Ｃｏｎｅ Ｗ ｉ ｔ ｈ Ｒｕｂｂｅｒ Ｅｄｇｅ
＊１／２＂ Ｔｉ ｔ ａｎｉ ｕｍ Ｄ ｏｍ ｅ Ｔｗ ｅｅｔ ｅｒ Ｉ ｎ Ｓｗ ｉ ｖｅｌ Ｍ ｏｕｎｔ
＊１／２＂ Ｔｉ ｔ ａｎｉ ｕｍ Ｄ ｏｍ ｅ Ｔｗ ｅｅｔ ｅｒ Ｉ ｎ Ｓｗ ｉ ｖｅｌ Ｍ ｏｕｎｔ
＊Ｐｏｗ ｅｒ： ２５０ Ｗ ａｔ ｔ ｓ Ｒａｔ ｅｄ Ｐｅａｋ
＊Ｐｏｗ ｅｒ： ３００ Ｗ ａｔ ｔ ｓ Ｒａｔ ｅｄ Ｐｅａｋ
＊Ｆｒｅｑｕｅｎｃｙ Ｒｅｓｐｏｎｓｅ： ４０Ｈ Ｚ－２０ＫＨ Ｚ
＊Ｆｒｅｑｕｅｎｃｙ Ｒｅｓｐｏｎｓｅ： ３５Ｈ Ｚ－２０ＫＨ Ｚ
＊Ｉ ｍ ｐｅｄａｎｃｅ： ８ Ｏ ｈｍ ｓ
＊Ｉ ｍ ｐｅｄａｎｃｅ： ８ Ｏ ｈｍ ｓ
＊Ｓｅｎｓｉ ｔ ｉ ｖｉ ｔ ｙ： ８９ ｄＢ
＊Ｓｅｎｓｉ ｔ ｉ ｖｉ ｔ ｙ： ８９ ｄＢ
＊ｗ ｉ ｔ ｈ Ｅｌ ｅｃｔ ｒｏｎｉ ｃ Ｃｒｏｓｓｏｖｅｒ Ｎ ｅｔ ｗ ｏｒｋ
＊ｗ ｉ ｔ ｈ Ｅｌ ｅｃｔ ｒｏｎｉ ｃ Ｃｒｏｓｓｏｖｅｒ Ｎ ｅｔ ｗ ｏｒｋ
＊Ｓｕｐｐｌ ｉ ｅｄ Ｗ ｉ ｔ ｈ Ｒｏｕｎｄ Ｇ ｒｉ ｌ ｌ ｅｓ Ａ ｎｄ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ
＊Ｓｕｐｐｌ ｉ ｅｄ Ｗ ｉ ｔ ｈ Ｒｏｕｎｄ Ｇ ｒｉ ｌ ｌ ｅｓ Ａ ｎｄ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ
＊Ｓｉ ｚｅ： Ｒｏｕｎｄ ／ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ： １１ "／１１ "＊１１ "
１
１
１
＊Ｓｉ ｚｅ： Ｒｏｕｎｄ ／ Ｓｑｕａｒｅ Ｇ ｒｉ ｌ ｌ ｅｓ： １２ "／１２ "＊１２ "
５ ／
５ ／
５ ／
＊Ｃｕｔ ｏｕｔ Ｓｉ ｚｅ： ９ "
５ ／
２
＊Ｃｕｔ ｏｕｔ Ｓｉ ｚｅ： １０ "
＊Ｍ ｏｕｎｔ ｉ ｎｇ Ｄ ｅｐｔ ｈ： ３ "
１
２ ／
＊Ｍ ｏｕｎｔ ｉ ｎｇ Ｄ ｅｐｔ ｈ： ３ "
IN-CEILING SPEAKER
INSTALLATION MANUAL
Ｔｈｉ ｓ ｐｒｏｄｕｃｔ ｇｅｔ ｓ ｔ ｈｅ ｐａｔ ｅｎｔ ｏｆ ｉ ｎｎｏｖａｔ ｉ ｏｎ ｏｆ ｔ ｈｅ ｓｔ ｒｕｃｔ ｕｒｅ， ｅａｓｙ ｆ ｏｒ ｉ ｎｓｔ ａｌ ｌ ａｔ ｉ ｏｎ．
Ｕ ｓｅ ｎｅｗ ｅｎｖｉ ｒｏｎｍ ｅｎｔ ａｌ ｐｒｏｔ ｅｃｔ ｉ ｏｎ Ａ ＢＳ ｍ ａｔ ｅｒｉ ａｌ ， ｗ ｉ ｔ ｈ ｌ ｏｎｇｅｒ ｓｅｒｖｉ ｃｅ ｌ ｉ ｆ ｅ， ｎｏｔ ｅａｓｙ ｔ ｏ ｃｈａｎｇｅ ｃｏｌ ｏｒ．
www.pyleaudio.com
-2-
INSTALLATION
TOOLS NEEDED
The in-wall/in-ceiling speakers
were designed to be easily
installed.However,if you are
unsure of your ability to prop-
Pencil
Phillips #2 screwdriver
erly install these loudspeakers
please contact your dealer or a
quali fied installer.
１
２ ／
２ ／
１
１
２ ／
Measuring tape
Utility knife
Carpenter's level
Awl
TROUBLESHOOTING
４
４
４
IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:
５ ／
５ ／
５ ／
１
２ ／
Check that receiver/amplifier is on and a source is playing.
４
５ ／
Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make
sure none of the speaker wires are frayed,cut,punctured or tounching each other.
Review proper proper operation of your receiver/amplifier.
IF THERE IS NO SOUND COMING FROM ONE SPEAKERS:
Check the"Balance"control on your receiver/amplifier.
Check allwires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make
sure none of the speaker wires are frayed,cut,punctured or tpunching each other.
IF THERE IS LOW(OR NO)BASS OUTPUT:
Make sure the connections to the left and right"speaker Inputs"have the correct polarity(+ and -).
Consider adding a powered subwoofer to your system.
In Dolby Digital or DTS modes,make sure your receiver/processor is corectly configured.When using a subwoofer,
make sure thesubwoofer output of the receiver/processor has been enabled.If no subwoofer is being used,
make sure the left and right front and rear speakers have been configured as"LARGE"See your receiver/processor's
owner's manual for futher information on correct speaker configuration in Dolby Digital,DTS and other surround sound
modes.
IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:
Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make
sure none of the speaker wires are frayed,cut,punctured or touching each other.
If more than one pair of main speakers is being used,check the minimum-impedance requirements of your
receiver/amplifier.
-3-
Thank you for purchasing this PYLE in-wall/in-ceiling speaker system.It is a
REAR SPEAKERS
state-of-the-art product carefully designed and manufactured for your installation
needs,and has been thoroughly tested to ensure consistent and reliable perfor-
mance.
If you have any question about the installation or operation of your PYLE
in-wall/in-ceiling speaker system which are not answered by this manual,contact
your dealer immediately.
WALL
WALL
WALL
INCLUDED
IN-CEILING
IN-CEILING SPEAKERS
Proper placement of the speakers is an imporant step in obtaining
the most realistic soundstage possible.These recommendations are
for the optimum placement of the londspeakers.Use these placement
recommendations as a guide. Slight variations will not diminish your
listening pleasure.The front speakers should be placed the same di--
stance from each other as they are from the listening position.They
should be placed at about the same height from the floor as the liste-
ner's ears will be,with the tweeters aimed toward the listener at ear-level height.In a home theater configu-
ration,the two surround,speakers should be placed slightly behind the listening position and ideally should
face each other and be at a level higher than the listener's ears.If that is not possible,they may be placed in
a wall(or in the ceiling)behind the listening position,facing forword.The surround speakers should not call
One pair of speakers with grilles.
attention to themselves.They should provide a diffuse,ambient sound accompanying the main program mat-
erial heard in the front speakers. In Dolby*Digital and DTS systems,aim the tweeters toward the listening
One pc of speakers with grills
for PDIC56/PDIC66/PDIC86/PDIC106
position at ear-level height.
SPEAKER CONNECTIONS
CONNECTION TIPS
M4x60mm
4pcs
The wires for both speakers
should be the same length.If
srtips of
adhesive
Screws
Template
one speaker is placed closer to
the amplifer than the other,
hide the excess wire behid
SPEAKER PLACEMNT
the wall.Speakers and elec-
tronics terminals have corre-
sponding(+)and(-)terminals.
We use red to denote the(+)termi-
FRONT SPEAKERS
nal and black for the(-)termi-
LEFT
RIGHT
nal.It is important to connect
both speakers identically:(+)on
WALL
the speaker to(+)on the ampli-
fier and(-)on the speaker to(-)
40
0
60
0
on the amplifier.Wireing
of phase" results in thin sound,
weak bass and a poor stereo
LEFT
RIGHT
Front or Rear Speaker Outputs
-4-
EXISTING CONSTRUCTION
IN-CEILING SPEAKERS
5-6FT
WALL
Cut the drywall.
Connect the speaker wires to
Screw down each of the four
Note:Always allow at least
the speaker.
Phillips head screws.The
one-half inch between a wall
locking tabs will swivel into
stud and the speaker cutout or
place and secure the unit to
the locking tabs will not be able
the rear surface of the drywall.
to swivel into place.
Put in the strips of adhesive to
secure the grille.
image.With the advent of multi-
channel surround sound
systems,connecting all of the
speakers in your system with
the correct polarity remains
equally important in order to
preserve the proper ambience
and directionality of the
program material.
Replace the metal grille.
Complete.
"
out
-5-
-6-
1600-63rd Street
Brooklyn,NY 11204 USA
Advertisement
