Surveon SMR2000 Series Quick Installation Manual

Warning!
Only qualified service personnel should install and service this product in order to avoid risk of injury from
electrical shock and energy hazard.
Caution!
Observe all ESD (Electro-static Discharge) procedures during installation to avoid damage to the recorder
and its components.
Accessories User Provided Components
Quick Installation Guide x1 3.5" SATA Hard Drive (at least x2)
● ●
Product DVD x1 (including manuals) Keyboard
● ●
Power Cord x1 Mouse
● ●
HDD Screw x20 (SMR2000 series) Monitor
● ●
HDD Screw x40 (SMR5000/8000 series)
●
SMR8000 Series
Overview
1
Front View
SMR5000 Series
SMR2000 Series
1 2 3 4 5
4 5
6
7
6
1 LCD Display 4 LED Indicators
2 Enter Switch 5 Power Switch
3 Select Switch 6 Front USB Connector
Note: The function of Video Back Up Button is reserved.
Rear View
SMR8000 Series
SMR5000 Series
SMR2000 Series
1
2
8
3
2
3
4
4
5
5
6
8 8
6
7
1 Power Socket 6 VGA Port
2 e-SATA Port x1 7 12V DC Power Port
3 USB Port x4 8 Kensington Lock-hole
4 LAN Port (GbE Ethernet port) x2 9 COM Port
5 Restore Button 10 HDMI Port
© by Surveon Technology, Inc. All rights reserved.
SMR Series

Before You Start

QUICK INSTALLATION GUIDE

Check list for Operating Environment

Users need to prepare the following devices to set up the surveillance system.
NVR
IP Camera
Network
Storage
Note: The hard drives should be purchased separately.

System Diagram

Tools Required
Flat blade Philips
screwdriver screwdriver
Remote Client
(Optional)
2 3 4 5

Check Network Topology

Make sure you have the right switch/hub for your environment. Either of the following options will work.
Existing LAN
Router
6
Switch/Hub
7 Video Back Up Button
Note: For devices without DHCP Server function, please refer to the section "Configuring DHCP Service"
in SMR User Manual.
.

Hard Drive Installation

Hard Drive Installation Prerequisites

When purchasing hard drives, the following factors should be considered:
• Capacity: Use drives with the same capacity. (The maximum is 2TB for SMR2000/5000 series, and 3TB
for SMR8000 series.)
• Drive type: The system uses SATA interface 3.5-inch hard drives. Please ensure that you purchase the
correct hard drives.
13

Inserting Hard Drive into Drive Tray

3
4
1. Open the front panel of the SMR system.
6
2. Press the release button (indicated by the blue arrow)
9
on the bezel, the bezel panel should open automatically
10
5
and gently pull out the hard drive tray.
11
1
12
11 USB Port x2
12 Safety Switch
3. Place the hard drive into the drive tray.
13 Audio Ports
Make sure the hard drive's interface
connector is facing the open side of the
drive tray and its label side facing up.
Adjust the drive's location until the
mounting holes in the drive tray are aligned
with those on the hard drive. Secure the
drive with four supplied flat head screws.
SMR series
Network Cameras (such as Surveon CAM2320)
Existing LAN, Switch, Router or Hub (please see the Network Topology below)
Hard Drives
IP Cameras
IP Encoder
SMR Series
VGA Management Station
& Live View
Common Topology Reference Product
LAN Switch with DHCP Server
LAN Switch with built-in DHCP Server D-Link DIR-130
No DHCP Server function (refer to the Note below) D-Link DES-1108
4. With the tray bezel open, insert the hard drive and
tray into the system enclosure.
5. Close the tray bezel.
6. Use the small flat blade screwdriver to turn the bezel lock
from the unlock to lock position.
Analog Cameras
7. Repeat above steps to install other hard drives.
8. Close the system front panel when you are done installing hard drives.
Cabling
USB Port
Office LAN
Upper
LAN Port
VGA Port
5

Powering up SMR

LED Indicators
LCD Display Power Switch

Logging into SMR

6
The VMS Client will prompt for the following information after the SMR system is powered on:
VMS/NVR:
Local Host - 127.0.0.1
Username: admin
Password:
Auto Login
• VMS/NVR – Local host for the SMR Server, which can not be changed.
• Username – The username for the domain, which is always admin.
• Password – The password for the domain. Default password is admin.
Click Login after the password is entered.
Please turn over the page and continue the installation process.
• Insert mouse, keyboard or other external devices to the USB port to operate
the Video Management Software (VMS).
• Insert the LAN cable to the upper LAN port to connect the SMR to a local
network where your IP cameras reside. (Connection to analog cameras is
also available via an IP encoder.)
• Connect an external monitor capable of 32bit or higher color quality to the
VGA Port to view the VMS interface.
Note: Users can only use the upper LAN port.
1. Press the Power Switch.
2. See if the System LED is blinking, which means that the
system is starting up.
3. See if the Network LED has turned green, which indicates
that power is on and network is connected.
4. See if the HDD LED is on, which means that the hard drive
can be accessed.
5. The Server name and the IP address will be shown on the LCD
screen (SMR5000/8000 series).
Login Shut Down