Moxa Technologies CN2610-8 Quick Installation Manual

CN2600 Series

Quick Installation Guide

Fourth Edition, September 2014
Overview
The Moxa CN2600 dual-LAN terminal servers have 8 or 16 RS-232
or RS-232/422/485 ports and dual 10/100 Mbps Ethernet LAN
ports, and some models come with dual AC power inputs. The
CN2600 terminal servers are used to connect terminals, modems,
printers, and other serial devices to LAN hosts, and all models
comply with TCP/IP and IEEE 802.3 specifications using standard
twisted pair 10/100BaseTX cable as the transmission medium.
CN2600 Series Models
The CN2600 Series includes the following models: CN2610-8,
CN2610-8-2AC, CN2610-16, CN2610-16-2AC, CN2650-8,
CN2650-8-2AC-T, CN2650-8-2AC, CN2650-16, CN2650-16-2AC-T,
CN2650-16-2AC, CN2650I-8, CN2650I-8-2AC, CN2650I-16,
CN2650I-16-2AC, CN2650I-8-HV-T, CN2650I-16-HV-T.

Package Checklist

The CN2600 dual-LAN terminal server products are shipped with
the following items:
• 1 CN2600 series terminal server
• Power cord (AC models only)*
• 1 DB9 serial cable (CBL-RJ45F9-150)
• 1 DB25 serial cable (CBL-RJ45M25-150)
• Rackmount kit (includes 2 brackets and 8 screws)
• Quick installation guide (this guide)
• Documentation and software CD-ROM
* Power cords are available with US, Euro, UK, and JP plugs.
Hardware Introduction
NOTE The wide temperature models do not come with the LCM
display panel and push buttons. The LCM description below
applies only to standard temperature models.
P/N: 1802026000214
– 1 –
Front Panel
Color Description
LED
Press the Reset button for 5 seconds to load
Reset None factory defaults. The CN2600 will beep twice
when the configuration has been reset.
Used for configuring the IP address and other
Red
Ready parameters.
Green Lights up when the CN2600 system is ready.
Serial Tx Green Flashes to indicate serial port transmission.
Serial Rx Yellow Flashes to indicate serial port reception.
Rear Panel
– 2 –
LCM Display
If the CN2600 is working properly, the LCM panel will display a
green color. The red Ready LED will also light up, indicating that
the CN2600 is receiving power. After the red Ready LED turns to
green, you will see a display similar to the following: (Example)
C N 2 6 1 0 - 1 6 _
1 9 2 . 1 6 8 . 1 2
CN2610-16: The CN2610's name
03: The CN2610's local sequence number
192.168.127.254: The CN2610's IP address
There are four push buttons on the CN2600 nameplate:
Button Name Action
Activates the main menu, or returns to an
MENU menu
upper level.
up Scrolls up through a list of items shown on the
cursor LCM panel's second line.
down Scrolls down through a list of items shown on
cursor the LCM panel's second line.
Selects the option listed on the LCM panel's
SEL select
second line.
Use the buttons to access the CN2600's function menus. As you
move through the functions and settings, the top line shows the
current menu or submenu name, and the bottom line shows the
submenu name or menu item. Press the SEL button to access the
item displayed on the bottom line.
Refer to CN2600 series User's Manual for more details.

Hardware Installation

Installing the CN2600
Open the package and attach the CN2600 to a desktop, or fasten it
to the rack cabinet.
Wiring Requirements
1. Use separate paths to route wiring for power and devices. If
power wiring and device wiring paths must cross, make sure
the wires are perpendicular at the intersection point.
2. NOTE: Do not run signal or communication wiring and power
wiring in the same wire conduit. To avoid interference, wires
with different signal characteristics should be routed
separately.
3. Where necessary, we strongly advise labeling wiring to all
devices in the system.
– 3 –
3
7 . 2 5 4