Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
J23083BK
Fastening to a concrete slab is highly recommended for optimal panel alignment and
correct functionality of moving parts.
A recess (75mm wide x 25mm deep) around the perimeter of the concrete slab is
recommended to minimise water ingress.
Further details about securing this product to the ground are on page 24 of this manual.
ABSCO INDUSTRIES
Page 1
MARCH 17
Advertisement
Table of Contents
Related Manuals for Absco J23083BK
Summary of Contents for Absco J23083BK
- Page 1 INSTRUCTION MANUAL J23083BK Fastening to a concrete slab is highly recommended for optimal panel alignment and correct functionality of moving parts. A recess (75mm wide x 25mm deep) around the perimeter of the concrete slab is recommended to minimise water ingress.
-
Page 2: Table Of Contents
INSTRUCTION MANUAL J23083BK CONTENT PAGE SITE & PREPARATION PACKING LIST SNAPTiTE ASSEMBLY JOINING SPLICED CHANNELS SPLICED CHANNEL ASSEMBLIES PANEL ASSEMBLY—LID (E) PANEL ASSEMBLY—REAR (A) PANEL ASSEMBLY—SIDE (B & C) PANEL ASSEMBLY—FRONT (D) PANEL ASSEMBLY—DOOR A PANEL ASSEMBLY—DOOR B PANEL ASSEMBLY - DOOR FITTINGS WALL ASSEMBLY HINGING &... -
Page 3: Site & Preparation
INSTRUCTION MANUAL J23083BK SITE & PREPARATION This is a do-it-yourself product which requires several tools (illustrated on the left) along with basic construction skills and knowledge. Use this manual as a guide, and be mindful of positioning parts square, centred and level where applicable throughout the assembly processes illustrated. -
Page 4: Packing List
PACKING LIST J23083BK ABSCO INDUSTRIES Page 4 MARCH 17... - Page 5 PACKING LIST J23083BK ABSCO INDUSTRIES Page 5 MARCH 17...
- Page 6 PACKING LIST J23083BK ABSCO INDUSTRIES Page 6 MARCH 17...
- Page 7 PACKING LIST J23083BK ABSCO INDUSTRIES Page 7 MARCH 17...
-
Page 8: Snaptite Assembly
INSTRUCTION MANUAL J23083BK SNAPTiTE ASSEMBLY The SnapTite assembly system locks most perimeter channels to all roof and wall sheets without the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and... -
Page 9: Joining Spliced Channels
INSTRUCTION MANUAL J23083BK JOINING SPLICED CHANNELS DRILL 4x 3mm (0.12") (2 PER A SIDE) HOLES TO SECURE SECTIONS TOGETHER. (THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) STEP ONE STEP TWO STEP THREE STEP FOUR... -
Page 10: Spliced Channel Assemblies
INSTRUCTION MANUAL J23083BK SPLICED CHANNEL ASSEMBLIES NOTE: SOME CHANNELS HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY CHANNEL WHERE THE CSJ JOINING CHANNEL COVERS HOLES ON THE CHANNELS YOU ARE CONNECTING JOIN TOGETHER 12 X CHANNEL SECTIONS... -
Page 11: Panel Assembly-Lid (E)
INSTRUCTION MANUAL J23083BK 1) Ensure that 54S & 54T Channels are centred on Sheets. 2) Do not install FAST001 Screws in splicing holes on 3) Do not install FAST001 Screws in splicing holes on underside of 54S Channel: these will not be installed underside of 54T Channel: these will be installed with as they would interfere with the hinging of this panel. - Page 12 INSTRUCTION MANUAL J23083BK 1) Install 2x FAST001 Screw to each 91G Jamb from underside. 2) Install remaining FAST001 Screws from top as illustrated. 3) Remove initial FAST001 Screws and install from top. ABSCO INDUSTRIES Page 12 MARCH 17...
-
Page 13: Panel Assembly-Rear (A)
INSTRUCTION MANUAL J23083BK ABSCO INDUSTRIES Page 13 MARCH 17... -
Page 14: Panel Assembly-Side (B & C)
INSTRUCTION MANUAL J23083BK 1) Drill hole in 88M Lip as indicated in DETAIL C. 2) Fit 88M Lip to 61B Channel once 61B Channel has been fitted to X3L/R Sheet. ABSCO INDUSTRIES Page 14 MARCH 17... -
Page 15: Panel Assembly-Front (D)
INSTRUCTION MANUAL J23083BK The FAST001 Screws illustrated in this process locate the 54R Channels onto the Sheets in an important position which will determine correct alignment of the doors and lid. It is important that these are installed before proceeding further. - Page 16 INSTRUCTION MANUAL J23083BK 7) Place the 90A Jamb into position 1) Ensure that 54R Channels are secured to 39D Sheets. by nesting end notches around the 2) Place the 89R Jambs into position by nesting end edges of the 89R Jambs notches around the high edges of 54R Channels.
-
Page 17: Panel Assembly-Door A
INSTRUCTION MANUAL J23083BK 1) Tuck the 20mm Face of the 91A Jamb into the Bottom 58C Channel. 2) Install 2x FAST001 Screw to each 91A Jamb from back. 3) Install remaining FAST001 Screws from front as illustrated. 4) Remove initial FAST001 Screws and install from front as illustrated. -
Page 18: Panel Assembly-Door B
INSTRUCTION MANUAL J23083BK 1) Tuck the 20mm Face of the 91A Jamb into the Bottom 58C Channel. 2) Install 2x FAST001 Screw to each 91A Jamb from back. 3) Install remaining FAST001 Screws from front as illustrated. 4) Remove initial FAST001 Screws and install from front as illustrated. -
Page 19: Panel Assembly - Door Fittings
INSTRUCTION MANUAL J23083BK ABSCO INDUSTRIES Page 19 MARCH 17... -
Page 20: Wall Assembly
INSTRUCTION MANUAL J23083BK ABSCO INDUSTRIES Page 20 MARCH 17... -
Page 21: Hinging & Bracing
INSTRUCTION MANUAL J23083BK ABSCO INDUSTRIES Page 21 MARCH 17... -
Page 22: Door & Lid Assembly
INSTRUCTION MANUAL J23083BK 1) Holes for FAST007 are not pre-punched & will require drilling. ABSCO INDUSTRIES Page 22 MARCH 17... - Page 23 INSTRUCTION MANUAL J23083BK ABSCO INDUSTRIES Page 23 MARCH 17...
-
Page 24: Anchoring
INSTRUCTION MANUAL J23083BK 1) Prior to anchoring, the Lid Panel can be manoeuvred to align with the Front Panel. 2) Look for a neat fit with respect to the Lid Panel fitting over the Side Panels. 3) Look for a neat alignment that aligns the Door Panels relative to one another as square as possible. -
Page 25: Hasp & Staple Installation
INSTRUCTION MANUAL J23083BK 1) Install HASP63 first, & align STAPLE accordingly. 2) Holes for STAPLE & FAST007 are not pre-punched & will require drilling. 3) Ensure that your shed is anchored prior to fitting these components. ABSCO INDUSTRIES Page 25... -
Page 26: Warranty Information
This warranty covers any Absco product used for normal domestic use and installed in accordance with the installation instructions. The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.