Eol Class 10A; Eol Out 0; Locked Rotor Level 0.5; Locked Rotor Trip Time 0.2 - ABB PSTX30 Installation And Commissioning Manual

Complete list
01 Motor rated current Ie
02 Start and stop
03 Limit
04 Kick start
05 Slow speed
06 Motor heating
07 Motor braking
08 Sequence start
09 Automatic restart
10 Internal IO 11 External IO
12 Communication
13-19 Protections list 1-7
20-24 Warnings list 1-5
25 Internal faults
26 External faults
27 Presentation
28 Service
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
01 Motor rated current Ie
01.01 Motor rated current Ie
03 Limit
03.01 Current limit type
03.02 Current limit level
03.03 2nd curr lim level
03.04 2nd curr lim time
03.05 Torque limit level
04 Kick start
04.01 Kick start
04.02 Kick start level
04.03 Kick start time
05 Slow speed
05.01 Slow speed forward
05.02 Slow speed fwd strength
05.03 Slow speed reverse
05.04 Slow speed rev strength
06 Motor heating
06.01 Motor heating capacity
07 Motor braking
07.01 Stand still brake strength
09 Automatic restart
09.01 Auto-reset delay time
09.02 Auto-restart
09.03 Auto-restart max attempts
10 Internal
10.03 In2 function
10.04 K4 function
10.05 K5 function
10.06 K6 function
10.07 AO reference
10.08 AO type
10.09 AO max value
10.10 AO min value
10.11 Ext therm sensor - ID
For full parameter list see chapter 7
Warnings list 20-24
20.01 EOL level
20.02 EOL out
20.03 EOL warning
20.04 Locked rotor level
20.05 Locked rotor init time
20.06 Locked rotor out
20.07 Locked rotor
20.08 Thyristor OL out
20.09 Thyristor OL
For full parameter list see chapter 7
27 Presentation
27.01 Language
27.02 Basic set-up at power on
02 Start and stop
02.01 Start mode
02.02 Stop mode
02.03 Start ramp initial level
02.04 Start ramp time
02.05 Stop ramp end level
02.06 Stop ramp time
02.07 Pre-start function
02.08 Pre-start timea
08 Sequence start
08.01 Sequence mode
08.02 Ie seq 1
08.03 Start mode seq 1
08.04 Start ramp time seq 1
08.05 Start ramp init lvl seq 1
08.06 Curr lim level seq 1
08.07 Kick start seq 1
08.08 Kick start level seq 1
08.09 Kick start time seq 1
08.10 Torque lim lvl seq 1
08.11 Torque tune seq 1
08.12 Torque ctrl gain seq 1
For full parameter list see chapter 7
11 External IO
11.01 1DI0 function
11.02 1DI1 function
11.03 1DI2 function
11.04 1DI3 function
11.05 1DI4 function
11.06 2DI5 function
11.07 2DI6 function
11.08 2DI7 function
11.09 1DO0 function
For full parameter list see chapter 7
25 Internal faults
25.01 Shunt fault out
25.02 Shunt fault op
25.03 Short circuit out
25.04 Short circuit op
25.05 Open circuit thyr out
25.06 Open circuit thyr op
25.07 Thyristor OL out
25.08 Thyristor OL op
25.09 Heat sink over temp out
25.10 Heat sink over temp op
25.11 Unspecified fault out
25.12 Unspecified fault op
26 External faults
26.01 Phase loss out
26.02 Phase loss op
28 Service
26.03 Bad network out
26.04 Bad network op
28.01 ID
26.05 Low supply voltage out 28.02 Line contactor close time
26.06 Low supply voltage op
28.03 TOR relay delay time
26.07 High current out 28.04 Start without start command
26.08 High current op
28.05 Step down level
26.09 Faulty usage out 28.06 Torque profile start
26.10 Faulty usage op 28.07 Torque finish
26.11 Faulty connection out 28.08 Torque tune
26.12 Faulty connection op 28.09 Torque ctrl gain
28.10 Torque PI intergration time
28.11 Torque slip
28.12 Torque diff
28.13 Torque filter time
For full parameter list see chapter 7
12 Communication
12.01 Com3 function
12.02 FB interface connector
12.03 Fieldbus control
12.04 Fieldbus address
12.05 Fieldbus IP address
12.06 Fieldbus IP gateway
12.07 Fieldbus IP netmask
12.08 Fieldbus IP DHCP client
12.09 FB baud rate
12.10 FB parity
12.11 FB stop bits
12.12 Fieldbus DI 1
For full parameter list see chapter 7
13-19 Protections list
13.01 EOL mode
13.02 EOL class
13.03 EOL dual class
13.04 EOL out
13.05 EOL operation
13.06 Locked rotor level
13.07 Locked rotor trip time
13.08 Locked rotor delay time
13.09 Locked rotor out
13.10 Locked rotor op
13.11 Max no of starts per hour
13.12 Max no of starts per hour out
13.13 Max no of starts per hour op
For full parameter list see chapter 7
6