Information On The Identification Plate; Serial Number; Ce Label; Energy Saving Trust Endorsed Products - Vaillant ecoTEC sustain 24 Installation And Maintenance Instructions Manual

4 Set-up

3.2

Information on the identification plate

The identification plate is mounted on the underside of the
product in the factory.
The identification plate keeps record of the country in which
the product is to be installed.
Information on the Meaning
identification plate
Condensing techno- Efficiency class of the boiler in accord-
logy ance with EC Directive 92/42/EEC

Serial number

For quality control purposes; 3rd and 4th
digits = year of production
For quality control purposes; 5th and 6th
digits = week of production
For identification purposes; 7th to 16th
digits = product article number
For quality control purposes; 17th to 20th
digits = place of manufacture
... ecoTEC ... Product designation
Cat. Approved gas category
Type: Xx3(x) Permissible flue gas connections
2H / 2E / 3P / 2K... Gas group and gas connection pressure
as set at the factory
Tmax Max. flow temperature
PMS Maximum water pressure in heating
mode
NOx NOx class for the product
V Electric connection
Hz
W Max. electrical power consumption
IP Protection class
Code (DSN) Specific product code
Heating mode
Qn Nominal heating load range in heating
mode
Pn Nominal heat output range in heating
mode
Pnc Nominal heat output range in heating
mode (condensing technology)
Hot water generation
Qnw Nominal heating load range in hot water
handling mode
Pnw Nominal heat output range in hot water
handling mode
D Specific flow rate
PMW Maximum water pressure in hot water
handling mode
Barcode with serial number
GC No. Gas council number
Note
Make absolutely sure that the product is compat-
ible with the gas group at the installation site.
8
3.3 Serial number
The serial number can be found on a plastic label at the bot-
tom of the front casing and on the identification plate.
3.4

CE label

The CE label shows that the products comply with the basic
requirements of the applicable directives as stated on the
identification plate.
The declaration of conformity can be viewed at the manufac-
turer's site.
3.5

Energy Saving Trust Endorsed Products

Only the most energy efficient products can carry the
'Energy Saving Trust Endorsed Product' brandmark making
it easy for consumers to choose products that have met strict
energy performance criteria.
Available for: Boilers, Heating controls and chemical inhib-
itors, the Energy Saving Trust endorsed product brandmark
gives consumers confidence that a product will cost less to
run, help lower energy bills and reduce carbon emissions.
About the Energy Saving Trust
Energy Saving Trust is an independent and impartial organ-
isation that provides trusted energy saving advice to em-
power millions of people to lead affordable, low energy life-
styles. For more information visit energysavingtrust.org.uk
4 Set-up
4.1

Transporting the unit

Important: With regard to the regulations of 1992 concerning
the manual handling of loads, the unit exceeds the weight
that can be lifted by a single person.
4.1.1 General
▶
Hold the load as close as possible to your body. Do not
twist your body – instead, reposition your feet.
▶
If the unit is being lifted by two persons, ensure your
movements are coordinated during lifting.
▶
Avoid bending your upper body – do not lean forwards or
to the side.
▶
Wear appropriate cut-resistant and non-slip gloves to
protect yourself against sharp edges and maintain a safe
and secure grip.
▶
If required, get somebody to assist you in this.
4.1.2 Unloading the box from the delivery van
▶
It is recommended that two people lift the unit together.
▶
Lift the box using the straps provided.
▶
Use safe lifting techniques – keep your back straight and
bend your legs at the knee.
▶
Hold the load as close as possible to your body.
Installation and maintenance instructions ecoTEC sustain 0020253094_01