Advertisement
Quick Links
For use with:
3,200 RPM Angle Head Tools
02649 Bearing
54515 Spacer
54529 Shim Packet (as req.)
01041 Grease Fitting
01041 Grease Fitting
Parts included in kit are identified. See reverse side for Tune-up Instructions.
54514 Blades (5) (5/pkg.)
11016 Bearing
54520 Bearing
54520 Bearing
For Models succeeding serial number N24309
54536 Shim
54542 Ball Bearing
54537 Ball Bearing
For Models prior to serial number N24309
54536 Shim
54534 Ball Bearing
54537 Ball Bearing
*For use with models prior to S/N N24309 Only
*54567 Spindle Puller
95809 Tune-Up Kit
01041 Grease Fitting
54542 Ball Bearing
54531 Needle Bearing
*54568 Spindle Wrench
Parts Page Reorder No. PD96•29
Effective May, 1996
01017 Pin
95398 Bearing
54545 Shim
95398 Ball Bearing
54529 Shim
DYNABRADE
54523 O-Ring
54508 O-Ring
01022 Spring
01024 O-Ring
01025 O-Ring
®
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Dynabrade 95809
Summary of Contents for Dynabrade 95809
- Page 1 Parts Page Reorder No. PD96•29 Effective May, 1996 95809 Tune-Up Kit For use with: 3,200 RPM Angle Head Tools Parts included in kit are identified. See reverse side for Tune-up Instructions. 02649 Bearing 54514 Blades (5) (5/pkg.) 01017 Pin 54523 O-Ring...
- Page 2 Motor should operate at 3,200 RPM at 90 PSI (6.2 Bar). RPM should be checked with a tachometer. If machine is running at a higher RPM then the tool should be serviced to correct the cause before use. Before operating, Dynabrade recommends that 2-3 drops of pneumatic tool oil be placed directly into air inlet with throttle lever depressed and that...
- Page 3 Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools WARNING (ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade's Warning/Safety Operating Instructions for more complete safety information.
-
Page 4: Maintenance Instructions
Operates 28 CFM @ 90 PSI has 3/8" NPT female ports. 5. Gear case of this Dynabrade air tool should be lubricated every 16 hours of use by using 95541 Grease Gun and 95542 Grease. - Page 5 Assembly/Disassembly Instructions 3,200 RPM Angle Head Tools A complete motor tune-up kit, Part No. 95809, is available which includes assorted parts to help maintain motor in tip-top shape. Warning: Manufacturers warranty is void if tool is dissembled before warranty expires.
- Page 6 Frequent drainage of water traps in air lines is recommended. Each tool on each drop should also be equipped with a secondary air processing unit. This consists of an in-line Filter-Regulator-Lubricator. All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
- Page 7 Accessories 50055: 1/4" Collet 95987 54585 – 5/16" open-end 95809 Motor Tune-Up Kit: (mates to tool spindle). Side Handle Assembly • 1/4"-28 male thread. Includes assorted parts to • Standard on 51091 Die Grinder. help maintain motor in tip- top shape.
- Page 8 3" Diameter Polishing Buffs 90030: Foam Waffle 90027: Terry Cloth 90028: Synthetic Wool • Scrim back. • Mount to 50120 or 50125 Hook Face Pads Terry Cloth Synthetic Wool Foam Waffle ® DYNABRADE Discover other shop supplies & consumables on our website.
Need help?
Do you have a question about the 95809 and is the answer not in the manual?
Questions and answers