SuperServer 6038R-TXR Quick Reference Guide
Board Layout
1
2
3
4
5
6
7
8
9
10 11 12 13
14
UID-SW
VGA
IPMI LAN
JUIDB1
LAN2
LAN1
USB 0/1 (2.0)
USB 4/5 (3.0)
UID-LED
LED1
X10DRX
FANC
BMC CTRL
LAN CTRL
BMC FWR
LEM1
CPU2
BIOS
CPU1
26
JBAT1
Battery
JBT1
25
PCH
USB 6 (3.0)
SP1
S-SATA2
S-SATA1
S-SATA0
USB 2/3 (2.0)
FAN6
CPU1
FANB
Front CTRL Panel
JVR1
25 23
22
21
20
19
18 17
No.
Description
CPU1 Slot1 PCI-E 3.0 x8
1
CPU1 Slot2 PCI-E 3.0 x8
2
CPU1 Slot3 PCI-E 3.0 x8
3
CPU1 Slot4 PCI-E 3.0 x8
4
5
CPU1 Slot5 PCI-E 3.0 x8
CPU2 Slot6 PCI-E 3.0 x8
6
CPU2 Slot7 PCI-E 3.0 x8
7
CPU1 Slot8 PCI-E 3.0 x8
8
9
CPU2 Slot9 PCI-E 3.0 x8
10
CPU2 Slot10 PCI-E 3.0 x8
11
CPU2 Slot11 PCI-E 2.0 x4 (in x8)
DIMME1(Blue)/DIMME2 slot
12
DIMMF1 (Blue)/DIMMF2 slot
13
14
CPU2 Socket
15
DIMMH1 (Blue)/DIMMH2 slot
16
DIMMG1 (Blue)/DIMMG2 slot
17
DIMMA1 (Blue)/DIMMA2 slot
18
DIMMB1 (Blue)/DIMMB2 slot
19
CPU1 (it must be installed on it first)
20
DIMMD1 (Blue)/DIMMD2 slot
21
DIMMC1 (Blue)/DIMMC2 slot
22
JBT1 = Clear CMOS
23
(S-)SATA 3.0 Ports #0~3
24
(I-)SATA 2.0 Ports #0~4
25
JSD1 & JSD2 = SATA Device Power Connector
Memory
15 16
Notch
COM1
FAN5
FAN4
Note: Notch should align
with the receptive key
point on the slot.
Release Tab
FAN7
CPU2
Top View of DDR4 Slot
Processors and their Corresponding Memory Modules
Corresponding DIMM Modules
CPU#
CPU 1
P1-DIMMA1
P1-DIMMB1
P1-DIMMC1
P1-DIMMD1
CPU 2
P2-DIMME1
P2-DIMMF1
P2-DIMMG1
P2-DIMMH1
Processors and Memory Module Population for Optimal Performance
Number of
CPU and Memory Population Configuration Table
CPUs + DIMMs
(For memory to work properly, follow the instructions below)
1 CPU & 2 DIMMs
CPU1 & P1-DIMMA1/P1-DIMMB1
1 CPU & 4 DIMMs
CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1
CPU1 & P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 +
1 CPU & 5~8 DIMMs
Any memory pairs in P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots
2 CPUs & 4 DIMMs
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1
2 CPUs & 6 DIMMs
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1
2 CPUs & 8 DIMMs
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1
2 CPUs & 10~16 DIMMs
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1
+ Any memory pairs in P1, P2 DIMM slots
2 CPUs & 16 DIMMs
CPU1 + CPU2 & P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,
P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2
Populate DIMM Memory Modules
Speed (MT/s) and Voltage Validated by Slot per Channel (SPC) and
Type
Ranks
Memory Capacity
per DIMM
Per DIMM (GB)
1 Slot Per Channel
&
(See the Note below)
Data Width
1DPC
4Gb
8Gb
8GB
2133
RDIMM
SRx4
16GB
RDIMM
SRx8
4GB
8GB
2133
RDIMM
DRx8
8GB
16GB
2133
RDIMM
DRx4
16GB
32GB
2133
LRDIMM
QRx4
32GB
64GB
2133
Note: For detailed information on memory support and updates, please refer to the SMC
Recommended Memory List posted on our website at
http://www.supermicro.com/support/resources/mem.cfm.
Notch
Front View
Release Tab
P1-DIMMA2
P1-DIMMB2
P1-DIMMC2
P1-DIMMD2
P2-DIMME2
P2-DIMMF2
P2-DIMMG2
P2-DIMMH2
2
No.
1
DIMM Per Channel (DPC)
2
2 Slots Per Channel
3 Slots Per Channel
1DPC
2DPC
1DPC
2DPC
3DPC
1.2V
2133
1866
2133
1866
1866
2133
1866
2133
1866
1866
2133
2133
1866
1866
1866
Beep Code/LED
1 beep
2133
1866
2133
1866
1866
2133
2133
2133
2133
2133
5 short beeps + 1 long
beep
5 long beeps + 2 short
beeps
1 continuous beep
Front View & Interface
i
i
8
9
7
6
5
4
3
2
1
No.
Description
Power Button
1
Reset Button
2
Screw #B
Power LED
3
4
Device Activity LED
5
LAN1 LED & LAN2 LED
6
Information LED
7
Power Failure LED
8
Hard Drive Signal
9
Hard Drive Fail
Rear View
Screw #C
1. Place heatsink on top of installed CPU
2. Line up the four screws to socket
3. Push down heatsink and screw down as shown
(cross pattern, in order: A, C, B, D)
4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten
each screw, to avoid damaging the system
1
Description
!
SAFETY INFORMATION
IMPORTANT: See installation instructions and safety warning
11 Standard PCI Slots
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
Power Supply Module
!
WARNING:
Beep Codes
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
If any CPU socket empty, install protective plastic CPU cap
BIOS Beep Codes
Message
Description
!
CAUTION:
Refresh
Circuits have been reset.
Always be sure all power supplies for this system have
(Ready to power up)
the same power output. If mixed power supplies are
Memory
No memory detected
installed, the system will not operate.
Display memory
Video adapter missing or with
For more information go to :
read/write status
faulty memory
http://www.supermicro.com/support
System
System overheat
http://www.supermicro.com
MNL-1747-QRG
CPU Installation
Align CPU to socket;
install CPU straight down
!
NOTE:
Do not bend pin inside socket
Heatsink Installation
Screw #A
Screw #D
Caution
ÌMNL-1747-QRG6Î
Need help?
Do you have a question about the SuperServer 6038R-TXR and is the answer not in the manual?
Questions and answers