Specifications - Garmin AQUAMAP 10x2 Series Installation Instructions Manual

Item
DC Power supply / battery
1
Power cable
2
Horn
3
Lamp
4
Relay (1 A coil current)
5
Toggle switches to enable and disable lamp or horn alerts
6
Item Wire Color
Red Power supply +
1
Black Power supply - / Ground
2
Yellow Alarm
3
HDMI Out Video Considerations
®
To prevent corrosion due to moisture, you must use Garmin GPSMAP
accessory cables when connecting the chartplotter to the video display. Using
different cables voids your warranty.
Through the HDMI OUT port, you can duplicate the chartplotter screen on
another device, such as a television or monitor.
The Garmin GPSMAP HDMI accessory cable is 4.5 m (15 ft) long. If you need
a longer cable, you should use an active HDMI cable only. You need an HDMI
coupler to connect the two HDMI cables.
You must make all cable connections in a dry environment.
Item
AQUAMAP 10x2/12x2 series MFD
1
GPSMAP HDMI cable (HDMI OUT)
2
Third party display with an HDMI port, such as a monitor or television
3
Dry environment, protected from moisture
4
Composite Video Considerations
This chartplotter allows video input from composite video sources using the
port labeled CVBS IN. When connecting composite video, you should observe
these considerations.
• The CVBS IN port uses a BNC connector. You can use a BNC to RCA
adapter to connect a composite-video source with RCA connectors to the
CVBS IN port.
• Video is shared across the Garmin Marine Network, but it is not shared
across the NMEA 2000 network.
8
Description
Wire Function
NOTICE
Description

Specifications

Device
AQUAMAP Dimensions (W x H x D)
10x2 series
Weight
Display size (W x H)
Display type
Display resolution
Max. power usage at 10 Vdc
Typical current draw at 12 Vdc 1.9 A
Max. current draw at 12 Vdc
AQUAMAP Dimensions (W x H x D)
12x2 series
Weight
Display size (W x H)
Display type
Display resolution
Max. power usage at 10 Vdc
Typical current draw at 12 Vdc 2.2 A
Max. current draw at 12 Vdc
Sonar Frequencies*
models
Transmit power (RMS)**
®
Depth***
All models Temperature range
Material
Water rating****
Fuse
Input power
Memory card
Max. waypoints
Max. routes
Max. active track points
Compass-safe distance
NMEA 2000 LEN
NMEA 2000 draw
* Dependent upon transducer.
**Dependent upon transducer rating and depth.
***Dependent upon the transducer, water salinity, bottom type, and other
water conditions.
****The device withstands incidental exposure to water of up to 1 m for up to
30 min. For more information, go to Garmin.com/waterrating.
Specification Measurement
318 x 185 x 69 mm
(12 / x 7 /
1 5
2 16
4.1 lbs (1.85 kg)
224 x 125 mm (8
WSVGA
1024 x 600 pixels
32.4 W
2.7 A
359 x 227 x 69 mm
(14 1 / x 8 5 /
8 16
2.34 kg (5.2 lbs)
262 x 164 mm (10
WXGA
1280 x 800 pixels
34.8 W
2.9 A
Traditional: 50/77/83/200 kHz
Single Channel CHIRP: 40 to 240 kHz
Garmin ClearVü CHIRP:
260/455/800 kHz
Traditional 50/77/200 kHz sonar: 2 kW
CHIRP: 1 kW
Garmin ClearVü and SideVü CHIRP:
500 W
5,000 ft at 2 kW
-15° to 50°C (5° to 122°F)
Polycarbonate plastic and die-cast
aluminum
IEC 60529 IPX7
8 A, 125 V fast-acting
10 to 32 Vdc
2 SD card slots; 32 GB max. storage
®
5,000
100
50,000 points, 50 saved tracks
65 cm (25.5 in.)
2
75 mA max.
AQUAMAP™ 10x2/12x2 SERIES
x 2 / in.)
11
16
/ x 4 / in.)
3 15
4 16
x 2 11 / in.)
16
/ x 6 / in.)
5 7
16 16