Logik L24FED13 Quick Start Manual

Quick Start Guide
22" / 24" LED TV
with DVD Player
L22FED13 / L24FED13
The latest eco-friendly power-saving technology will switch off the TV if
device is left on and idle for 4 hours. Please refer to "Auto Standby" under
the "Time Settings" section of the instruction manual for more detail.
Thank you
for purchasing your new Logik TV.
Your new TV incorporates the latest technology to enhance your viewing experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful rst time installation.
1 1
Unpacking
Remove all packaging from the TV. Retain the packaging.
If you dispose of it please do so according to any local
regulations.
TV Screw A x 1
TV Stand Support Screw B x 3
TV Base Rear Spacer x 4
Instruction Manual
Remote Control /
AAA Batteries x 2
Quick Start Guide
3 3
Installing the Base Stand
1. Lay the TV down on a flat surface with the back side facing up. Please make sure a soft cushioned material (such as a pillow or thick piece of foam) is
placed beneath the screen.
2. To install the TV stand, first attach the stand support to the TV by using screw A. Align the screw hole then use screw A to fix the stand support to the TV.
3. To install the base stand, align the screw hole, then secure with a screw driver (not included) using the screw B provided.
Screw A x 1
2 2
Operating Your Remote Control
1. Press and lift the back cover to open the
battery compartment of the remote
control.
2. Insert two AAA size batteries. Close the
battery compartment cover.
Make sure the (+) and ( – ) ends
of the batteries match the (+)
and ( – ) ends indicated in the
battery compartment.
screw
TV Front
screw
Base Stand
Front
Screw B x 3
4 4
Connecting the Aerial
OR
RF Coxial Cable
(not included)
COMMON INTERFACE (CI)
USB HDMI2 HDMI1 PC IN
HEADPHONE PC AUDIO
Connect one end of the RF coaxial cable to the aerial socket on the
wall and the other end of the cable to the RF (75Ω) socket at the rear
right side of your TV.
Do not connect the TV to the mains supply until you
have completed all the connections.
6 6
Turning the TV On for the First Time
The first time you turn the TV on, it will go straight into First Time Installation menu.
1. Press the OK button to start
First Time Installation
First Time Installation menu.
Please ensure aerial is plugged in!
Then press OK button.
2. Press the buttons to
Please select an OSD Language
select your desired language to
be displayed on the menu. The
English esky Suomi
default on-screen menu
Svenska Slovak
language is set as English.
Press the OK button to confirm.
Dansk Norsk
OK
3. Press the buttons to select
Mode Select
your desired mode and then
press the OK button. Press the
Home Mode
button to select Yes to confirm
Shop Mode
button to select No to
or the
cancel and return to the Mode
Select menu.
OK
7 7
Target Region Setting
This will be shown as GBR for the UK.
During tuning your TV may have received signals
This will show the regional country
from more than one transmitter. If this has occurred
(e.g. England, Wales, Scotland, NI).
the Target Region Setting screen will be displayed.
This will enable you to select the correct regional
This will allow you to set the region for
transmission for the local news service that you
your local news service.
require.
Press the buttons to adjust each option's setting
You may receive signals from more than
and then press the OK button to confirm.
one transmitter within the Secondary
Region, (e.g Beds and Cambs may have
Luton or Sandy Heath).
Well done,
your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these
features, please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on 0844 561 1234.
Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
5 5
Connecting to the Mains Socket
RF
1. Connect the mains cable to the mains socket after you have
completed all the connections.
2. At this stage, the TV switches to standby mode. The red LED
indicator will illuminate on the front panel of the TV.
3. In standby mode, press the button on the right side panel of the
TV or on the remote control to turn the TV on. The red LED
indicator will turn blue.
4. Press the
Country
select the country where you
will operate the TV. Press the
Portugal Serbia Sweden
OK button to confirm.
Rumania Slovenia Switzerland
Russian Spain UK
OK
5. DTV channel tuning will
Channel Tuning
commence. This operation may
take up to 3 minutes. The
TV : 0 Channel(s)
display will show the progress of
DTV : 3 Channel(s)
the tuning and the number of
Radio : 0 Channel(s)
channels found.
Data : 0 Channel(s)
36%... 668.75MHz (DTV)
Press [MENU] to skip.
Target Region Setting
Country Code
Primary Region
Secondary Region
Tertiary Region
(QSG-L22_24FED13-140125V2)
To mains
socket
buttons to
GBR
England
London