Master/Slave Mode ..................5. Mainte nanc e ................Product Maintenance ..................6. Te c hnic al S pe c ific atio ns ............7. Re turns ..................8. Co ntac t Us .................. Intimidator Spot 260 User Manual Rev. 1...
Electronically published by Chauvet in the United States of America. CHAUVET, the Chauvet logo, and Intimidator Spot 260 are registered trademarks or trademarks of Chauvet & Sons LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries.
Keep this User Manual for future use. If you sell the product to someone else, be sure that they also receive this document. Page 2 of 20 Intimidator Spot 260 User Manual Rev. 1...
NTRODUCTION 2. I NTRODUCTION Product Overview Focus Lens IR Sensor Power In Control DMX In Menu Screen Buttons DMX Out Power Out Fuse Microphone Safety Loop Intimidator Spot 260 User Manual Rev. 1 Page 3 of 20...
7.64 in 322 mm 194 mm 5.12 in 130 mm 6.06 in 4.17 in 154 mm 106 mm 3.19 in 4.33 in 5.83 in 81 mm 110 mm 148 mm Page 4 of 20 Intimidator Spot 260 User Manual Rev. 1...
ETUP AC Power The Intimidator Spot 260 has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Intimidator Spot 260 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes.
Selects the 180° tilt angle range Selects the 90° tilt angle range Normal mode Totem Mode Totem mode Base Up DOWN Totem mode Base Down Sensitivity 001–100 Sets sound sensitivity Intimidator Spot 260 User Manual Rev. 1 Page 7 of 20...
If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. The Intimidator Spot 260 uses up to 14 DMX channels, which defines the highest configurable address to 499.
255 Reverse cycle effect, slow to fast 007 No function 119 Clockwise rotation, slow to fast Gobo Rotation 231 Counter-clockwise rotation, slow to fast 255 Bounce, slow to fast Intimidator Spot 260 User Manual Rev. 1 Page 9 of 20...
Page 12
199 Sound-active movement macro 4 215 Sound-active movement macro 5 231 Sound-active movement macro 6 247 Sound-active movement macro 7 255 Sound-active movement macro 8 Page 10 of 20 Intimidator Spot 260 User Manual Rev. 1...
Page 13
231 Counter-clockwise rotation, slow to fast 255 Bounce, slow to fast 015 No function Prism 255 3-facet prism Focus 255 Focus, big to small Intimidator Spot 260 User Manual Rev. 1 Page 11 of 20...
Press <ENTER>. Use <UP> or <DOWN> to select Sound. Press <ENTER>. Sound Sensitivity To change the sound sensitivity on the Intimidator Spot 260, follow the instructions below: Press <MENU>. Use <UP> or <DOWN> to select Setup. Press <ENTER>. Use <UP> or <DOWN> to select Sensitivity.
Use <UP> or <DOWN> to select from 540 (540°), 360 (360°), or 180 (180°). Press <ENTER>. Tilt Angle To set the tilt angle range on the Intimidator Spot 260, follow the instructions below: Press <MENU>. Use <UP> or <DOWN> to select Setup.
Press <ENTER>. Use <UP> or <DOWN> to select Reset. Press <ENTER>. Factory Reset To restore the Intimidator Spot 260 to factory default settings, follow the instructions below: Press <MENU>. Use <UP> or <DOWN> to select Setup. Press <ENTER>. Use <UP> or <DOWN> to select Factory Set.
PERATION IRC-6 Infrared Remote Control The Intimidator Spot 260 is compatible with the IRC-6 infrared remote control from Chauvet. To activate IR mode, follow the instructions below: Press <MENU>. Use <UP> or <DOWN> to select Run Mode. Press <ENTER>. Press <UP> or <DOWN> to select IR.
The Master/Slave mode allows a single Intimidator Spot 260 product (the “master”) to control the actions of one or more Intimidator Spot 260 products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in Stand-Alone, while the slave products will be set to operate in Slave mode.
Softly drag any dirt or grime to the outside of the transparent surface. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Intimidator Spot 260 User Manual Rev. 1 Page 17 of 20...
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. Chauvet reserves the right to use its own discretion to repair or replace returned product(s). Intimidator Spot 260 User Manual Rev. 1 Page 19 of 20...
Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., United Kingdom, Ireland, Benelux, France, Germany, or Mexico contact the dealer of record. Page 20 of 20 Intimidator Spot 260 User Manual Rev. 1...