Table of Contents
Advertisement
POWER/STANDBY indicator
Power
POWER/
Power
management
STANDBY
management
mode
indicator
operating status
On
Green
Not activated.
Off
Red
Activated.
Setting the picture to suit the movie
The film image is automatically discriminated and
projected in an image mode suited to the picture.
[NTSC, PAL, PAL60, 480I (60Hz), 525I (60Hz), 576I
(50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only]
Example: Setting the "CINEMA MODE" to "OFF"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
1. On the MAIN MENU, select "OPTION2", then press
the MENU/ENTER button.
The "OPTION2" screen appears.
2. Use the
and
buttons to select "CINEMA MODE".
3. To set the CINEMA MODE to "OFF" ...
Use the
and
buttons to select "OFF".
The mode switches as follows each time the
button is pressed:
ON
OFF
OPTION2
PREVIOUS PAGE
POWER MGT.
CINEMA MODE
LONG LIFE
GRAY LEVEL
S1/S2
NEXT PAGE
SEL.
ADJ.
Information
CINEMA MODE
ON ................... Automatic discrimination of the
image and projection in cinema mode.
OFF ................... Cinema mode does not function.
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults.
Description
Turning the picture
back on
Horizontal and vertical
Picture already on.
synchronizing signals
are present from the
computer.
Horizontal
and/or
Operate the keyboard or
vertical synchronizing
mouse.
The
picture
signals are not sent
reappears.
from the computer.
or
2 / 3
:
OFF
:
OFF
:
3
:
OFF
EXIT
RETURN
Reducing burn-in of the screen
The brightness of the screen, the position of the picture,
positive/negative mode and screen wiper are adjusted to
reduce burn-in of the screen.
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
1. On the MAIN MENU, select "OPTION2", then press
the MENU/ENTER button.
The "OPTION2" screen appears.
2. Use the
and
buttons to select "LONG LIFE", then
press the MENU/ENTER button.
The "LONG LIFE" screen appears.
PLE
ORBITER
INVERSE
SCREEN WIPER
SOFT FOCUS
SEL.
3. Set the LONG LIFE mode using
See below to set PLE.
See page 42 to set ORBITER.
See page 42 to set INVERSE.
See page 43 to set SCREEN WIPER.
See page 44 to set SOFT FOCUS.
Information
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults.
PLE (Peak Luminance Enhancement)
Use this to activate the brightness limiter.
Example: Setting "PLE" to "LOCK1"
Perform Steps 1-2 of LONG LIFE, then...
3. Use the
and
buttons to select "PLE".
4. Use the
and
buttons to select "LOCK1".
The mode switches as follows each time the
button is pressed:
AUTO
LOCK1
PLE
ORBITER
INVERSE
SCREEN WIPER
SOFT FOCUS
SEL.
Information
PLE settings
AUTO .............. The brightness of the screen is
adjusted automatically to suit the
picture quality.
41
LONG LIFE
:
AUTO
:
OFF
:
OFF
:
OFF
:
OFF
ADJ.
EXIT
RETURN
and
buttons.
LOCK2
LOCK3
LONG LIFE
:
LOCK1
:
OFF
:
OFF
:
OFF
:
OFF
ADJ.
EXIT
RETURN
or
Advertisement
Table of Contents
Troubleshooting
