Integra HDB-RX1 Instruction Manual

Instruction Manual
HDBaseT Receiver
HDB-RX1
En
SN29355998
* 2 9 3 5 5 9 9 8 *
What's in the Box
Main unit (1) AC adaptor (1) Cushions (4)
Screws for wall attachment (4) Label for HDBaseT cable (2)
TM
Label for AC adaptor cord (2)
Instruction Manual (this document)
®
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of HDMI Licensing LLC in the United States
and other countries.
HDBaseT TM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
All other trademarks are the property of their respective owners.
Part Names
F1711-0
 HDMI  General
Supported Power Supply
Deep Color, x.v.Color™, LipSync, 3D, 4K 60 Hz, Extended AC 100 - 240 V, 50/60 Hz
Colorimetry (sYCC601, Adobe RGB, Adobe YCC601), Power Consumption
Content Type, HDR 11.2 W (AC adaptor)
HDCP Dimensions (W × H × D)
Revision 1.4, 2.2 205 mm × 35 mm × 89 mm
Maximum Video Resolution 8-1/16" × 1-3/8" × 3-1/2"
4k 60 Hz (YCbCr 4:4:4) Weight
0.45 kg (1 lb)
 Output jacks
• Specifications and features are subject to change without
HDMI OUT : 1 notice.
• We will not accept responsibility for damage arising from the
 Other jacks
connection of equipment manufactured by other companies.
HDBaseT IN : 1
RS232 : 1 (Path through)
IR IN : 1 (Path through)
IR OUT : 1 (Path through)
1 Screw hole for wall attachment: Fix with the supplied screw for wall
attachment when installing on a wall.
2 12V 1A INPUT jack: When connecting to a device that does not
support Power over Cable (PoC, refer to the back cover), connect the
supplied AC adapter.
3 Power indicator: Lights when the power of this unit is on.
4 HDBaseT jack: Use an Ethernet cable to connect to the HDBaseT
OUT jack on one of our AV receivers to receive video signals, audio
signals, control signals, etc.
• As they are covered with a seal when shipped, remove it when you
use the jack.
• Use one of the following Ethernet cables to connect.
ｰ When using Power over Cable (PoC, refer to the back cover)
Cat6 (Category 6) cable: AWG23 cable or better, 50 m or less in
length
Cat5e (Category 5e) cable: AWG24 cable or better, 45 m or less in
length
ｰ When not using Power over Cable (PoC, refer to the back cover
Cat6 (Category 6) cable: AWG23 cable or better, 100 m or less in
length
Cat5e (Category 5e) cable: AWG24 cable or better, 90 m or less in
length
• It is recommended to use shielded single Ethernet cable.
• Do not connect this port to the Ethernet ports of network devices.
5 HDMI OUT jack: Transmit video signals and audio signals with a HDMI
cable connected to a monitor such as a TV or projector.
6 ACTIVE/SERVICE switch: Use in the "ACTIVE" position. ("SERVICE"
is for servicing)
7 RS232 port: Used when connecting to a home control system.
• Use a straight cable.
8 IR IN/OUT jacks: Used when connecting to a multiroom remote control
kit.
• Refer to the instruction manual of the IR receiver for the types of
cables required for connection.
35
89 64
189
205
Unit : mm
TM