Related Manuals for Felt TA FRD
Summary of Contents for Felt TA FRD
-
Page 1: Table Of Contents
CONTENTS: BAYONET FORK INSTALLATION AEROBAR INSTALLATION RISER, PAD, & EXTENSION INSTALLATION SEATPOST INSTALLATION SEATPOST HEAD & SADDLE INSTALLATION “TRAIN” CRANK INSTALLATION “RACE” CRANK INSTALLATION REAR WHEEL INSTALLATION FRONT WHEEL INSTALLATION COG & LOCKRING INSTALLATION... -
Page 3: Bayonet Fork Installation
BAYONET FORK INSTALLATION... -
Page 4: Aerobar Installation
AEROBAR INSTALLATION STEPS: Use 4mm Allen key to loosen M5x18 socket head cap screw on stem. Position Aerobar stem onto B3 tension nut, and align fork bolt to stem. While applying light, downward pressure on the stem, use a torque wrench with a 3/8”... -
Page 5: Riser, Pad & Extension Installation
Fit Washers STEPS: The TA FRD armrests can be set up in three distinct configurations—Low, Mid or High—each utilizing a unique selection of spacers to achieve the rider’s desired position. The Mid configuration can even be set up in two different heights, depending on the specific spacer used (5mm or 10mm). Refer to the diagrams on the following page for detailed views of the specific components required. -
Page 6: Riser, Pad, & Extension
RISER, PAD & EXTENSION INSTALLATION 40mm 6-8 Nm 45mm 6-8 Nm 55mm 6-8 Nm... - Page 7 RISER, PAD & EXTENSION INSTALLATION...
-
Page 8: Seatpost Installation
PARTS: REQUIRED TOOLS: Seatpost 4mm Allen key TA FRD seatpost wedge Torque wrench 2 x M5x18 socket head cap screw STEPS: Position wedge with taper facing towards the rear of the frame, and the end of the wedge with more material above the bolt hole to the top. -
Page 9: Seatpost Head & Saddle Installation
SEATPOST HEAD & SADDLE INSTALLATION: PARTS: REQUIRED TOOLS: 2 x Saddle Clamp Upper 4mm Allen key 2 x Saddle Clamp Adjustment Head Half Torque wrench 2 x Saddle Clamp Lower Friction paste Saddle Clamp Binder Nut Saddle Clamp Binder Bolt STEPS: Place each Saddle Clamp Upper into a Saddle Clamp Adjustment Head Half, positioning them so the hooked surfaces are adjacent and can grip a seatpost rail. - Page 10 SEATPOST HEAD & SADDLE INSTALLATION:...
-
Page 11: Train" Crank Installation
“TRAIN” CRANK INSTALLATION PARTS: REQUIRED TOOLS: Vision Track Crank, LHD, BB30, 144BCD 10mm Allen key 50, 51, 52, 53, 54, 55-tooth, 3/32” chain rings Torque wrench 5 x T30 8mm chainring bolts with nuts Grease “Left” 11.7mm aero spacer “Right” 7.7mm aero spacer Wave washer STEPS: Insert Left 11.7mm aero spacer onto crank spindle. - Page 12 “TRAIN” CRANK INSTALLATION...
-
Page 13: Race" Crank Installation
“RACE” CRANK INSTALLATION PARTS: REQUIRED TOOLS: Vision Metron Aero Crank, LHD, BB30, 130BCD 10mm Allen key 50, 51, 52, 53, 54, 55T 3/32” chain rings Torque wrench 5x T30 10mm chain ring bolts Grease “Left” 2.0mm aero spacer “Right” 7.7mm aero spacer Wave washer STEPS: Insert Left 2.0mm aero spacer onto crank spindle. - Page 14 “RACE” CRANK INSTALLATION...
-
Page 15: Rear Wheel Installation
REAR WHEEL INSTALLATION PARTS: REQUIRED TOOLS: Rear wheel 5mm Allen key 2 x M8x30 flat head socket cap screw Torque wrench 1 x “Left” aero washer for left drop out 1 x “Right” aero washer for right drop out STEPS: Insert rear wheel into 95mm rear drop out. - Page 16 REAR WHEEL INSTALLATION...
-
Page 17: Front Wheel Installation
FRONT WHEEL INSTALLATION PARTS: REQUIRED TOOLS: 2 x M6x20 flat head socket cap screw 4mm Allen key Torque wrench STEPS: Insert front wheel into 70mm front drop out. Thread M6x20 flat head socket cap screws into hubs. Tighten loosely with 4mm Allen key, then fully tighten to 6-8 Nm with torque wrench. -
Page 18: Cog & Lockring Installation
REQUIRED TOOLS: Phil Wood 13, 14, 15, 16-tooth, 3/32”, spline drive cogs Lockring Wrench Phil Wood, black, “FELT TEAM USA” 1.32x24 TPI, left-handed thread for “Train” wheels with black Phil Wood hubs Phil Wood or White Industries, silver, 1.29x24 TPI, left-handed thread for “Race”...