Advertisement
Getting Connected
To begin, you will need to connect to your RD-71 via IP 1
directly, or by adding the RD-71 to your local area network. The network
settings can be found via the front panel System > Network Menu. IP
addresses are dynamically set via DHCP. If you wish to assign a static
address, you will need to turn DHCP off prior to setting a manual
address.
To connect directly to the device, make sure that your computer
and the device have IP addresses within the same IP class range (ex.
192.168.10.48 for the device and 192.168.10.49 for your computer).
Using a CAT 5 crossover cable, connect one end to your computer and
the other to the IP 1 port found on the processor section of the back
panel. (Some computers can auto negotiate the connection and a
crossover may not be necessary.)
To add the device to a LAN, connect a standard CAT 5 Ethernet
cable to your network router or switch and then to the IP 1 port on the
back of the device.
Power .....................................................................................................................................
Power:
1 & 2 Redundant AC Power, Standard 3 pin computer power plug
(Auto range 70-240 VAC Input)
Processor ..............................................................................................................................
IP 1:
Management/Monitoring default port (10/100/1000BASE-T)
IP 2:
TSoIP UDP, RTP and SMPTE 2022 default port (10/100/1000BASE-T)
COM1:
Serial Port Used for Troubleshooting (Terminal)
COM2:
API Serial Communication Interface
Parport:
9-pin parallel I/O interface for control systems
RS422:
Not Currently Supported
GPIO:
Tally and Control Port
Decoder .............................................................................................................................
Analog Audio Out:
Balanced analog audio out. Stereo pairs 1 & 2. DB9
AES Audio Out 1-8:
75 Ohm AES-3 BNC
DVB-ASI x3 Out:
75 Ohm BNC
DVB ASI In:
75 Ohm terminated Input BNC
Sync In:
Standard analog video sync separation for NTSC, PAL, 480I/P, 576I/P, 720P, and 1080I/P/PsF from
Composite Video (CVBS). Bi-level & tri-level sync compatible. BNC
CVBS Out:
75 Ohm Standard De nition Composite Video Output BNC
Digital VIdeo Out:
Digital Video
** SDI Out 1 & 2
(2) 75 Ohm Outputs from decoder
** SFP Optical /Alt SDI Out (1) SFP interface, Module purchased separately. (1) 75 Ohm, BNC
** Note: Video/Audio/VBI Supported- (3G/HD-SDI) SMPTE 425M (Level A and DL-Level B ), SMPTE 424M, SMPTE 292M, (SD-SDI) SMPTE 259M-C
* Demodulator (optional)......................................................................................................................
RF 1 & RF 2:
RF input, 75 Ohm F-Connector
L-Band (LB) Model:
Dual Tuners capable of simultaneous lock. Supports L-Band, DVB-S/S2, QPSK, 8PSK, 16APSK, 32APSK*
* Software Key eld upgradeable to 16APSK and 32APSK.
Adtec Digital Technical Support: 615.256.6619 www.adtecdigital.com
Web-Based Control Application
serial number on the back of the device. Clicking on the unit in the Bonjour
login page. If you do not wish to use Bonjour, you can reach the device's web application by pointing
your browser to the IP Address of the device. Ex. http://192.168.10.48/. You will be prompted for a
username and password. The default username is 'adtec' . The default password is 'none' .
The left-hand panel of the application will report current status in real-time while the right
panel tabs will allow you to con gure your device.
Adtec Digital has adopted
zero-con guration networking
?
technology, streamlining the setup and
con guration processes for our products.
The use of this technology enables
automatic discovery of Adtec devices and
services on an IP network. Used in tandem
with the web-based control and
con guration applications we can now
Getting Started
provide 1-click access to any device.
By using the built-in Bonjour
locater in
©
Apple's
©
Safari
©
browser or the plug-ins
your network and you have inputs applied with active
readily available for IE
©
or Firefox
©
services, you can select which services you want to
browsers, users can locate all of the Adtec
decode via the web-based control application. The below
devices on a network by referencing the
image shows the Input > Services tab. From this tab, you
list will re-route you to a
©
can view all services available on your device, select one
of the services for decode or view more details about the
service. There is a 'Select First Found' option for each
input. When selected, this configuration will detect the
first valid service and decode it.
Note: IP service selection is treated differently than ASI or RF
inputs. To populate the IP services section, you need to first
visit the IP Params tab and set the correct Rx Address, port
and handling parameters. Return to the RD Services tab. Click
the 'Select First Found' radio button for IP. This will populate
the RD Services tab with services found on the IP input.
The most recent firmware releases are available on our
support website, www.adtecdigital.com. Advanced users can
find direct API command help as part of the on-board web
application, Help Tab.
Have questions?
Each field or group of fields in
our web-based application has a hint button associate
with it. It contains information on use of the field or
acceptable ranges.
Once your receiver is powered up, configured on
Advertisement
