Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Actidata actiLib Library 2U
Summary of Contents for Actidata actiLib Library 2U
-
Page 1: Quick Start Guide
Library 2U Quick Start Guide September , 2009... -
Page 2: Table Of Contents
Front panel.........................10 Rear panel .........................11 Labeling tape cartridges ......................13 Magazines ...........................14 Mailslot..........................14 Connecting the Library......................15 SCSI installation ........................16 installation........................16 Fibre-channel installation....................16 Configuring the library......................16 Power ON/OFF the library ......................17 actiLib Library 2U – Quick Start Guide Page 2 of 17... -
Page 3: Warnings And Symbols
Library 2U – Quick Start Guide Page 3 of 17... -
Page 4: Precautions
Install stabilizing feet on the rack. In multiple-rack installations, secure racks together. Extend only one rack component at a time. Racks may become unstable if more than one component is extended. actiLib Library 2U – Quick Start Guide Page 4 of 17... -
Page 5: Unpacking The Tape Library
The shipping lock is held in place with a label and is located in the top center of the library. After the shipping lock is removed, it should be stored on the rear panel right side of the library for future use. actiLib Library 2U – Quick Start Guide Page 5 of 17... - Page 6 Figure 1 Shipping lock and label Figure 2 Shipping lock and label on the rear panel Figure 3 Shipping lock before transportation actiLib Library 2U – Quick Start Guide Page 6 of 17...
-
Page 7: Rackmounting The Library
The library easily installs into a standard 19” rack system taking up 2U of space. WARNING! The actiLib Library 2U weighs 15.6 kg without media. To reduce the risk of personal injury or damage to the library: 1) observe local health and safety requirements and guidelines for manual material... - Page 8 Secure the library to the rack (see Figure 6) using a 3# Phillips screwdriver placed through the small holes in the mounting bracket to tighten the M5 screw on each side of the library. actiLib Library 2U – Quick Start Guide Page 8 of 17...
- Page 9 Figure 6 Securing the library to the rack actiLib Library 2U – Quick Start Guide Page 9 of 17...
-
Page 10: Actilib Library 2U Overview
128 x 64 characters The OCP screen displays actions and status information, menu items or error messages equivalent to the operation mode. Left Magazine with Mail slot actiLib Library 2U – Quick Start Guide Page 10 of 17... -
Page 11: Rear Panel
Back panel overview with one half height FC tape drive Same description as in table 2 except for the FC connectors and that the fan is moved to the left of the FC connectors. actiLib Library 2U – Quick Start Guide Page 11 of 17... - Page 12 Figure 10 Back panel overview with one half height SAS tape drive Same description as in table 2 except for the SAS connector. actiLib Library 2U – Quick Start Guide Page 12 of 17...
-
Page 13: Labeling Tape Cartridges
Before loading a cartridge into the library, make sure the write-protect switch on the front of the cartridge is in the desired position. Number Description Write-enabled Write-protected Write-protect switch Barcode label Insertion arrow Figure 10 Write-protecting the Ultrium data cartridge actiLib Library 2U – Quick Start Guide Page 13 of 17... -
Page 14: Magazines
In that case „Busy“ is displayed and the command has to be repeated once the robotics operation is finished. actiLib Library 2U – Quick Start Guide Page 14 of 17... -
Page 15: Connecting The Library
Figure 13 Attaching the SCSI cable to the LTO3 full height drive Figure 14 Attaching the terminator to the LTO3 full height drive Figure 15 Attaching the power cable actiLib Library 2U – Quick Start Guide Page 15 of 17... -
Page 16: Scsi Installation
3) Power-on the library. 4) Power up the host system. 5) Verify that each host can communicate with the library’s tape drives f. Configure your library using the library’s operator panel. actiLib Library 2U – Quick Start Guide Page 16 of 17... -
Page 17: Power On/Off The Library
To abort the shutdown process the user has to press Cancel within the first 3 seconds Note: The shutdown process may be aborted by pressing Cancel within the first 3 seconds. actiLib Library 2U – Quick Start Guide Page 17 of 17...
Need help?
Do you have a question about the actiLib Library 2U and is the answer not in the manual?
Questions and answers