B.E.G. LUXOMAT PD1-M-DIM Installation And Operating Instruction

LUXOMAT
Installation and Operating Instruction for B.E.G. - Occupancy detectors PD2-Master-DIM-SM/-FC/-FM
1. Mounting preparations
Work on the 230 V mains supply
may only be carried out by quali-
fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec-
trical personnel in accordance with
electrotechnical regulations.
Disconnect supply before installing!
When in Master/ Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
2c. Installation of the
LUXOMAT PD1-M-DIM-FM
®
The detector can
be installed in
conventional inlet-
sockets mounted
on the ceiling.
The assembly
plate enclosed
must be stripped
off prior to instal-
lation and secured
to the ceiling
using 4 screws
and ensuring that
it is not laterally
transposed.
Having connected up the cables in ac-
cordance with regulations, the detector
can be placed in position as shown in the
drawing opposite and, applying a little
pressure, can then be locked into position
with the assistance of the spring clips.
Option:
max
max
ON
ON
OFF
OFF
max
ON
OFF
max
ON
Wall bracket for remote
OFF
control IR-PDim
max
ON
OFF
2a. Installation of the LUXOMAT
For surface-mounting, an inwall sensor unit is combined with a surface-mounted
receptacle as a housing base.
Before mounting the base, the enclosed mounting plate must be mounted true to
side, i.e. the writing must be legible.
Now fix the base on ceiling or wall, but first put the cable through one of the
cable openings provided. The detector must be mounted on a flat, solid surface.
Next prepare the sensor part by screwing in both fixing screws, then connect the
cable as per the wiring diagram.
6 mm 6 mm
3. Putting into operation / Settings
Self test cycle
The product enters an initial 60-second self-test cycle, when
120 60 50 the supply is first connected. The occupancy detector is
A
40
ready for operation.
30
15
5 10
Follow-up time for light control
25 22
30
18
The time can be set infinitely variably at between
R1 16
10
1 and 30 minutes.
16 10
6
TEST
3 5
1
2
Symbol TEST: Test mode (Every movement switches on the
1
light for a period of 1 second, switching it off for a period
TEST
30
15
of 2 seconds after that regardless of the level of brightness.)
Twilight-switch for light control (relay 1)
2000
1200
The switch-on value for the light can be set at between 10
600
and 2000 Lux. Using the rotary control, the luminance set
200
40
points can be set as desired.
Symbol : Night-time operation
Symbol : Daytime / Night-time operation
Orientation lighting
ON
60
This rotary controller serves to determine the working time
50
30
of the orientation lighting (fixed to 20 %).
10
5
OFF "ON" for permanent orientation lighting.
"OFF" for deactiviation of orientation lighting.
Unlocking device
50 1500
Luminance set point for constant light regulation
Lux
Lux
50
50
1500
Lux
Lux
Lux
50
1500
Lux
Lux
Dimming
max
max The following approach will prove useful when setting a
command value (example workplace): Place a luxmeter flat
ON on the desk, then, using the remote control IR-PDim, adjust
ON the light up or down by pressing the keys max or min until
the desired command value which best suits your require-
OFF
ments has been reached.
OFF
Automatic reading in the current light value
50
as new luminance set point
Lux
50
50 1500
Individual light value 2 - 2500 Lux Lux
Lux
Lux
max
50
1500
Follow-up time
Lux
max Lux
max
1 up to 30 min.
ON
Orientation lighting and its follow-up time
ON
ON
OFF button: No orientation light.
20 %
OFF
Grey button: Programming the switch-off delay time.
OFF
OFF
On button: Orientation light is permanently activated.
50
1500
Lux Lux
Note: During the orientation light phase, the constant light
regulation is also active: if there is sufficient brightness,
dimming occurs < 2 V and, if applicable, the lighting is
switched off.
Preset / user mode => (see page 2, point 6)
Fully automatic/semi automatic mode => (see page 2, point 5)
Semi automatic: green LED,
Fully automatic: red LED on for approx. 3 sec.
50 1500
Lux Lux
Resetting when open
All values which have been programmed using the remote
control IR-PDim are deleted, and those values which have
been set by potentiometer are activated.
Lock device
PD1-M-DIM
®
® PD1-M-DIM-SM
Now insert the sensor part and check for matching positioning
of the two markings.
Press beyond the spring housing pressure so that the sensor
part firmly locks in place.
Now turn the sensor part counter-clockwise for about 10° to
the stop.
1500
Lux
1500
Lux
1500
Lux
max
ON
OFF
2b. Installation of the LUXOMAT
PD1-M-DIM-FC
Having connected up the cables in accor dance with
regulations, the detector is inserted into the opening
as shown in the drawing opposite and fixed into
position with the assistance of the spring clips.
4. Settings carried out using remote control (optional)
Remote control LUXOMAT IR-PDim
®
120 60 50
A
40
30
15
5 1. Check Battery:
10
open battery compartment by pressing the
16 10
plastic springs together and removing the
5
2
battery-holder.
1
TEST
30
15
1 2
2. IMPORTANT
25 22
2000
30
18
1200 Please pay attention, that the setting is Potentio-
R1 16
600
10 meter 1 at "TEST" and Potentiometer 2 not at
200
6
TEST
3 40
1
"SUN". All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position "TEST/
1 2
SUN". Please switch Potentiometer 2 over to
25 22 2000
"MOON" or any other value.
30
18 1200
R1 16
600
10
200
6
TEST
3
1 40
Caution:
Settings with remote control supersede the
settings by courtesy of potentiometers.
Lock device
Test mode
Reset to deactivate
Resetting when closed
The lighting relay is switched off, i.e.
opened and the follow-up times reset.
Permanent protection against sabotage
This function blocks the unit permanently (green LED is illuminated).
This operating mode can only be activated during the period of 5
seconds after pressing the "lock" button. This status will only
permit actuating the function "Light on/ Light off".
The procedure for leaving this mode is as follows:
1. Switch off the current
2. Apply current for 31 – 59 seconds
3. Switch of the current again
4. Apply current
50
1500
5. Open detector
Lux
Lux
Light on/ off
The light will remain switched on/off for as long as movements
are detected in the areas of coverage. Once the last movement
has been detected, the light will remain on for the duration of the
follow-up time as per setting.
The appliance will then return independently to the mode selected
(Fully or Semi-automatic).
GB
®
The detector has
been designed and
developed specifically
for installation in sus-
pended ceilings.
A circular opening of
diameter 68 – 70 mm
must be produced in
the ceiling.