Dell Wyse 3000 Installation And Setup Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Server
  5. Wyse 3000
  6. Installation and setup manual
Dell Wyse 3000 Installation And Setup Manual

Dell Wyse 3000 Installation And Setup Manual

Edge series microserver
Hide thumbs Also See for Wyse 3000:
Table of Contents

Advertisement

Quick Links

Dell Wyse 3000 Edge MicroServer Installation and
Setup Guide
July 2015

Advertisement

Table of Contents
loading

Related Manuals for Dell Wyse 3000

Summary of Contents for Dell Wyse 3000

  • Page 1 Dell Wyse 3000 Edge MicroServer Installation and Setup Guide July 2015...

  • Page 2: Table Of Contents

    Login to the Dell Wyse 3000 device ................2-1 Set Up a Websocket Connection ..................2-2 Establishing and Testing a Connection ..........3-8 Connect to the Dell WYSE 3000 via Serial Port .............. 3-8 Connect the Dell WYSE 3000 to the ThingWorx Platform ..........3-9 Troubleshooting ..............4-15...

  • Page 3: Introduction

    About the Dell WYSE 3000 The Dell WYSE 3000 is a multi-port x86 Intel-based thin client device, running Windows Embedded Standard 7. It is manufactured by Dell Inc., and is intended for use as a rapid-connecting specialized and limited-role device.

  • Page 4: Installation And Setup

    Installation and Setup Setup of the Dell WYSE 3000 with an EMS will first require connecting to the Dell Wyse 3000 from a computer via Ethernet cable and a local DHCP Server. Please note that this guide was written for a computer running Microsoft Windows.

  • Page 5: Set Up A Websocket Connection

    Windows from: http://www.dhcpserver.de/cms/ In Windows, before installing the DHCP server, open “Network and Sharing Center”, and then click the link on the left for “Change Adapter Settings” ThingWorx EMS Setup Guide for the Dell WYSE 3000 Page 2-2...
  • Page 6 IP address that starts with “192.168…”. Subnet Mask may be left as 255.255.255.0 Connect the Dell Wyse 3000 device to your computer with an Ethernet cable. Note: From here on out, you may wish to disable any connection to another network to...
  • Page 7 Select “Local Area Connection”, and confirm that its DHCP setting is disabled by default. On the next screen, check “HTTP (Web Server)” and leave the others unchecked. Click “Next”. ThingWorx EMS Setup Guide for the Dell WYSE 3000 Page 2-4...
  • Page 8 DHCP Server. 13. Open up a browser, and type in “localhost/dhcpstatus.xml” into the address bar. The Dell Wyse 3000 should be detectable and listed as a client, with an IP address assigned. ThingWorx EMS Setup Guide...
  • Page 9 Get the latest release of the “Win32” package. Transfer the MicroServer zip file to the Tip: You can create a shared folder on the Dell device and Dell WYSE. transfer the file over a LAN, or you can move it using a flash drive.
  • Page 10 In the browser on your host computer, navigate to the ThingWorx platform, and click “Monitoring”. Here, click “Remote Things”, and then click on the “Unbound” tab. Here, you should see the “MyGateway” entity here. ThingWorx EMS Setup Guide for the Dell WYSE 3000 Page 2-7...

  • Page 11: Establishing And Testing A Connection

    Establishing and Testing a Connection Connect to the Dell WYSE 3000 via Serial Port Connect the host computer to the Dell device’s serial port using an appropriate serial-serial or serial-USB cable. powershell Open a command prompt window on the computer, and type “powershell”.

  • Page 12: Connect The Dell Wyse 3000 To The Thingworx Platform

    $port.ReadLine() On the other computer, receive the message by typing: Connect the Dell WYSE 3000 to the ThingWorx Platform From the Starter Kit package, place the following included files in the following MicroServer directories on the Dell WYSE 3000: Place “config.lua” in the Dell’s \etc\ folder.
  • Page 13 Dell Device’s serial port number: Save the file when finished. Run the “wsems” executable under \MicroServer\, and then run “luaScriptResource” in the same directory. ThingWorx EMS Setup Guide for the Dell WYSE 3000 Page 3-10...
  • Page 14 The command prompt windows at right are similar to what you should see after running “wsems” and “luaScriptResource” ThingWorx EMS Setup Guide for the Dell WYSE 3000 Page 3-11...
  • Page 15 On the General Information page for this new Thing, click “Browse” next to its identifier field, and select “testit” from the available choices. Save the testThing entity when finished. ThingWorx EMS Setup Guide for the Dell WYSE 3000 Page 3-12...
  • Page 16 Bindings”, and then click the “Remote” “wsems” and “luaScriptResource” are both running on the tab at the top left of the new window. Dell device, and that the connection is established properly. Click and drag to add “testScriptDemo” remote property to the “testValue”...
  • Page 17 Note: The host computer is acting as both an originating property page for the “testThing” data injector, for which it sends data to the Dell WYSE via Thing, refresh the value for “testValue”. Serial Port, and as a host ThingWorx server, in which it receives a value response from the Dell device via websocket Its value should have changed to “Hello...

  • Page 18: Troubleshooting

    If not, make sure all Firewalls are disabled on both computers. Try changing the system clock on the Dell Device to make it match that of the host computer’s. Verify that the computer is connected to the Dell Device via serial cable.
  • Page 19 Confirm that the ThingWorx platform at the IP address specified in the settings.json file is up and running. This guide has been tested for compatibility with the Dell WYSE 3000 and the following ThingWorx platform and operating system: ThingWorx Platform Version ThingWorx 6.0.1...

Table of Contents