Jump Or Mop - PowerTec Digimax Installation And Operation Instruction Manual

ERROR CODE 15 -- ILLEGAL ATTEMPT TO CHANGE PARAMETER
The parameter which is being addressed at this time may not be changed at this time.
ERROR CODE 16 -- INCORRECT PROTOCOL NUMBER
The protocol parameter must be set to either 0, 2, or 3.
ERROR CODE 17 -- MAXIMUM RATIO EXCEEDED
The ratio entered exceeds the value in parameter #31. This may occur during entry into
parameter #31 or during ratio SETPOINT entry.
ERROR CODE 18 -- MAXIMUM RAMP VALUE EXCEEDED
The value entered in parameter #6 or #7 exceeds 999.9.
ERROR CODE 19 -- ILLEGAL PARAMETER NUMBER
In parameter mode, when attempting to go to a parameter number, a 0 or a number
greater than 36 will generate this error.
ERROR CODE 20 -- MAXIMUM PARAMETER VALUE EXCEEDED
The value entered in parameter exceeds the maximum allowed.
ERROR CODE 21 -- LESS THAN MINIMUM RATIO PARAMETER
The value entered as a ratio is less than that required by parameter #38.
ERROR CODE 99 -- UNKNOWN ERROR
This is a catch-all error statement which is displayed if the microprocessor detects an
error that does not fit into one of the above categories. If it occurs during parameter entry,
press PGM to exit program mode. If it occurs in NORMAL mode, press ENTER to clear it.
In some cases it may be necessary to remove and re-apply power to clear it.
JUMP OR M.O.P. JUMP OR M.O.P. JUMP OR M.O.P. JUMP OR M.O.P. JUMP OR M.O.P.
Parameter # 13 (page 18)
Parameter # 10 (page 17)
Parameter # 11 (page 18)
JUMP -- Pressing the UP button or activating the UP input (TB2 terminal 9) causes the
output of the DIGIMAX
button or activating the DOWN input (TB2 terminal 10) will decrease the output by the
amount set in parameter #11. When the key or input is released, the output will return to the
SETPOINT value at which it was prior to the pushbutton or input being activated.
This is a registration type function for the Brushless DC motor control. Because of the
exact speed control of the Brushless DC motor control, the motor shaft runs in a particular
position in its rotation (as seen by a strobe light) while it is at a constant speed. When the
output speed is temporarily increased or decreased, the effect on the motor is that its shaft
will move forward or backward from the position in which it was running before the UP or DN
buttons or inputs were activated.
MOP -- Pressing the UP key or activating the UP input changes the frequency
immediately by the amount in parameter #10, and then, after .5 second, increases the output
frequency at the rate set in parameter #6 until the input is released. The frequency will remain
at the value it attained when the input is released. Likewise, Pressing the DN key or
activating the DOWN input decreases the output frequency immediately by the amount set
in parameter # 11, and, after .5 second, at the rate set in parameter #7 until the input is
released. The frequency will remain at the value it attained when the input is released.
DIGIMAX Manual
® ® ® ® ®
ILLEGAL ATTEMPT TO CHANGE PARAMETER ILLEGAL ATTEMPT TO CHANGE PARAMETER ILLEGAL ATTEMPT TO CHANGE PARAMETER ILLEGAL ATTEMPT TO CHANGE PARAMETER
INCORRECT PROTOCOL NUMBER INCORRECT PROTOCOL NUMBER INCORRECT PROTOCOL NUMBER
INCORRECT PROTOCOL NUMBER
MAXIMUM RATIO EXCEEDED MAXIMUM RATIO EXCEEDED MAXIMUM RATIO EXCEEDED MAXIMUM RATIO EXCEEDED
MAXIMUM RAMP VALUE EXCEEDED MAXIMUM RAMP VALUE EXCEEDED
MAXIMUM RAMP VALUE EXCEEDED MAXIMUM RAMP VALUE EXCEEDED
ILLEGAL PARAMETER NUMBER ILLEGAL PARAMETER NUMBER ILLEGAL PARAMETER NUMBER ILLEGAL PARAMETER NUMBER
MAXIMUM PARAMETER VALUE EXCEEDED MAXIMUM PARAMETER VALUE EXCEEDED MAXIMUM PARAMETER VALUE EXCEEDED MAXIMUM PARAMETER VALUE EXCEEDED
LESS THAN MINIMUM RATIO PARAMETER LESS THAN MINIMUM RATIO PARAMETER LESS THAN MINIMUM RATIO PARAMETER
LESS THAN MINIMUM RATIO PARAMETER
UNKNOWN ERROR UNKNOWN ERROR UNKNOWN ERROR UNKNOWN ERROR
®
DIGIMAX DIGIMAX DIGIMAX DIGIMAX to increase by the amount set in parameter #10. Pressing the DN
Page 31