Reverse Input Mode; Up Input Mode; Installed Option Enable; Debounce Value - PowerTec Digimax Installation And Operation Instruction Manual

#33 REVERSE INPUT MODE

#33 #33 #33 #33 REVERSE INPUT MODE REVERSE INPUT MODE REVERSE INPUT MODE REVERSE INPUT MODE
The digital input at terminal 8 on TB2 is normally used to activate reverse mode
(parameter #9). When a "0" is entered in this parameter, that is the case.
When a "1" is entered , it becomes a general purpose input (subject to programming).
When a "2" is entered, the input at TB2 terminal 8 will toggle the unit between MASTER
and SLAVE modes. When the REVERSE input is off, the DIGIMAX
when the input is energized, the DIGIMAX
When a "3" is entered, the input at TB2 terminal 8 will toggle between MASTER and
SLAVE modes. When the input is energized, it will be SLAVE "inverse" mode. See page 32.
When swiching from SLAVE to MASTER, the DIGIMAX
speed. When switching from MASTER to SLAVE, the ratio is fetched from Parameter #37.
#34 #34

#34 UP INPUT MODE

UP INPUT MODE UP INPUT MODE UP INPUT MODE
#34 #34 UP INPUT MODE
The digital input at terminal 9 on TB2, is normally used to activate the INC mode
(parameters #10 and #13). When a "0" is entered in this parameter, that is the case.
When a "1" is entered, it becomes a general purpose input (subject to software).
#35 #35 #35 #35 #35 DOWN INPUT MODE DOWN INPUT MODE DOWN INPUT MODE DOWN INPUT MODE DOWN INPUT MODE
The digital input at terminal 10 on TB2, is normally used to activate the DEC mode
(parameters #11 and #13). When a "0" is entered in this parameter, that is the case.
When a "1" is entered, it becomes a general purpose input (subject to programming).
#36 #36 #36

#36 INSTALLED OPTION ENABLE

#36 INSTALLED OPTION ENABLE INSTALLED OPTION ENABLE INSTALLED OPTION ENABLE INSTALLED OPTION ENABLE
If there is no installed option (such as BCD input) this parameter should be set to "0".
To activate an installed option, change this parameter to "1".
#37 #37 COMMANDED RATIO SETPOINT COMMANDED RATIO SETPOINT
#37 #37 #37 COMMANDED RATIO SETPOINT COMMANDED RATIO SETPOINT COMMANDED RATIO SETPOINT
When using the external input to switch brtween MASTER and SLAVE modes, a ratio
MUST be entered in this parameter. The DIGIMAX
values are from 0.0000 to 7.9999. Entering a larger number will generate error code 17.
#38 #38 MINIMUM COMMAND RATIO MINIMUM COMMAND RATIO
#38 #38 #38 MINIMUM COMMAND RATIO MINIMUM COMMAND RATIO MINIMUM COMMAND RATIO
This parameter sets the minimum value a ratio is allowed to accept. Valid values are
from 0.0000 to 7.9999. If a lower ratio is entered, the DIGIMAX

#39 DEBOUNCE VALUE

#39 #39 DEBOUNCE VALUE DEBOUNCE VALUE DEBOUNCE VALUE
#39 #39 DEBOUNCE VALUE
This is the amount of time a control input must be present before it is considered a valid
input. Valid values are from 1 to 255. Each number is 4 ms, so the default of 8 is 32 ms.
#40 #40 #40 #40

#40 AT SPEED SOURCE

AT SPEED SOURCE AT SPEED SOURCE AT SPEED SOURCE AT SPEED SOURCE
This parameter specifies the source signal for the AT SPEED signal.
A "0" entered in this parameter means commanded speed is compared to actual.
A "1" entered means commanded speed is compared to the ramp output.
#41 #41 #41

#41 COMMUNICATIONS TURN AROUND TIME

#41 COMMUNICATIONS TURN AROUND TIME COMMUNICATIONS TURN AROUND TIME COMMUNICATIONS TURN AROUND TIME COMMUNICATIONS TURN AROUND TIME
This parameter sets the time in millisecond between the receipt of a message and the
response to it. The default is 2. The minimum is 0. The maximum is 255.
Page 22
®
DIGIMAX DIGIMAX DIGIMAX DIGIMAX will be in SLAVE "direct" mode. See page 32.
DIGIMAX DIGIMAX DIGIMAX
DIGIMAX
DIGIMAX DIGIMAX ®
DIGIMAX DIGIMAX looks to this parameter for a ratio. Valid
DIGIMAX DIGIMAX
DIGIMAX DIGIMAX
© copyright 1992-1996 by Powertec Industrial Motors
DIGIMAX DIGIMAX ®
DIGIMAX DIGIMAX will be a MASTER, and
®
will command the current
®
generates error 21.