Masibus 85XX+ Quick User Manual

Quick User Guide
85XX+ Scanner/DAQ
85XX+ Scanner/DAQ
Input Input
Range
Type Type
E - 2 0 0 t o 1 0 0 0  C CU53
J - 2 0 0 t o 1 2 0 0  C NI120
-10 to 20
K - 2 0 0 t o 1 3 7 0  C
mV
0 to 100
T - 2 0 0 t o 4 0 0  C
mV
B 4 5 0 t o 1 8 0 0  C 4-20mA
0 to 20
R 0 t o 1 7 5 0  C
mA
S 0 t o 1 7 5 0  C 0 – 5 V
N - 2 0 0 t o 1 3 0 0 ° C 1 – 5 V
RTD(PT100) -199.9 to 850.0C 0 – 10V
Table 1.1
SPECIFICATIONS
NO. OF CHANNEL 8 or 16 or 24
ACCURACY
TC/RTD/LINEAR: + 0.1% of instrument
range + 1 digit
RESOLUTION ADC: 17 bits
TC(E,J,K,T)/RTD/CU53/NI120: 0.1C
TC(B,R,S,N): 1C
LINEAR: 1 Count
APPLICABLE STANDARD DIN (ITS-90) for
Thermocouple and RTD
INPUT TYPE Refer table 1.1
SAMPLING PERIOD PER 50 ms for TC and Linear
INPUT Input and 100 ms for
RTD
BURNOUT CURRENT 0.4 µA
MEASUREMENT CURRENT 250 µA
INPUT IMPEDANCE >1 MΩ for RTD/Voltage
inputs, 250 Ω for
current Input
NMRR > 40 dB (50/60 Hz)
CMRR >120 dB (50/60 Hz)
ALLOWABLE WIRING Maximum 15 ohms/wire
RESISTANCE FOR RTD (Conductor resistance
between three wires
should be equal).
Doc.Ref. No. m83B/QG/101 Issue No.:00
Digital Input Specification (Optional)*
NUMBER OF
INPUT 16
CHANNELS
RATED 12 V DC 24 V DC
INPUT (Sink / (Sink /
VOLTAGE Source) Source)
INPUT ON
≥ 7 V ≥ 15 V
VDC
INPUT OFF
≤ 4 V ≤ 5 V
VDC
4 mA ± 4 mA ±
INPUT
20% / 20% /
CURRENT
Ch Ch
MAXIMUM
ALLOWABLE
15 V DC 30 V DC
INPUT
VOLTAGE
RESPONSE
50 mSec
Range
TIME
-210.0 to * With Digital Input, CE marking is not applicable/valid
210.0°C
-70.0 to Digital Output- Relay
210.0°C
NUMBER OF OUTPUTS 8
PURPOSE Alarm or trip or control or
watchdog output
OUTPUT SIGNAL Two terminals (C and NO)
- 1 9 9 9
t o 9 9 9 9
RELAY CONTACT 250 VAC / 30 VDC @ 2A
RATING
NUMBER OF RELAY 1 X 10^5 @ rated current
OPERATION
Digital Output- Open Collector (Optional)
NUMBER OF OUTPUTS 24
PURPOSE Alarm or trip or control or
watchdog output
OUTPUT TYPE transistor open collector
output selection)
CONTACT RATING 30 V DC,100 mA
Analog Output- Analog Output (Optional)*
NUMBER OF OUTPUTS 8
OUTPUT SIGNAL 0-20 mA, 4-20 mA or 0-5 V,
1-5 V, 0-10 V DC
LOAD RESISTANCE For current o/p, 550Ω Max.
For Voltage o/p, 3000Ω Min.
OUTPUT ACCURACY ±0.25% of span
* With Analog Output, CE marking is not applicable/valid.
Programming and Setting
KEYPAD 8-keys tactile membrane
keypad
CONFIGURATION All Configurable parameters can
SOFTWARE be set through PC Based
software
MEMORY Non-volatile, restored after
power loss
Communication Specification
NO. OF COMMUNICATION
PORT
COMMUNICATION TYPE
110 V 220 V
COMMUNICATION
DC DC
PROTOCOL
(Sink) (Sink)
≥ 75 V ≥ 110 V
MAXIMUM NO. OF UNITS
COMMUN. ERROR
≤ 30 V ≤ 50 V
DETECTION
2 mA / 2 mA /
PROFIBUS Communication (Optional) *
Ch Ch
MODE Profibus DP Slave
BAUD RATE 9600, 19.2K, 44.45K, 93.75K,
132 V 250 V 187.5K, 500K, 1.5M, 12M bps
DC DC
ADDRESS Configurable through Configuration
Software (0 to 125 Only)
NETWORK  Multi-drop up to 31 modules, Plus
CAPACITY a host, without a repeater
 Up to 125 modules plus a host if
four repeaters are used
COMMUICATION Up to 1200 meters without a
DISTANCE repeater using Type A wire
 1200m @ 115Kbps or less
 1000m @ 187.5Kbps
 400m @ 500Kbps
 200m @ 1.5Mbps
 100m @ 12Mbps
* With Profibus communi. , CE marking is not applicable
HMI Interface (Optional)*
NO. OF COMMUNICATION
PORT
COMMUNICATION TYPE
COMMUNICATION
PROTOCOL
CONNECTABLE NO. OF
UNITS
COMMUN. ERROR
DETECTION
Network Connectivity (Optional)
NO. OF COMMUNICATION
PORT
TRANSMISSION SPEED
NETWORK PROTOCOL
APPLICATION PROTOCOL
Data logging (Optional)
Data logging Memory Type
Data logging type
Periodic Memory Size
Event Memory Size
RTC Time format
Periodic Logging sampling
time
Event polling time
USB Port*
USB Function
Max. USB storage device
size
USB Mass storage device
format
2-RS485(COM-1 and
USB fetched data file format
COM-2) . COM2 is
Optional
USB data retrieving option
Half duplex/Asynchronous
MODBUS RTU. All *With USB port, CE marking is not applicable/valid.
parameters are
Display Specification
Configurable through
MODBUS Protocol. CHANNEL NO
32 DISPLAY
CRC Check DATA
DISPLAY
PARAMETER
DISPLAY
STATUS LEDs
Environmental Specification:
AMBIENT TEMPERATURE
HUMIDITY
TEMPERATURE COEFFICIENT
WEIGHT
INSTRUMENT WARM-UP
TIME
DEGREE OF PROTECTION
Power Supply Specification
RATED VOLTAGE
1-RS-232 (HMI)
POWER CONSUMPTION
Half
duplex/Asynchronous
MODBUS RTU
Isolations (Withstanding Voltage)
 Between primary terminals* and secondary
1
terminals**: 1500VAC for 1 minute
 Between secondary terminals: 500V AC for 1
CRC Check
minute
* Primary terminals indicate power terminals and
relay output terminals
1(RJ-45)
** Secondary terminals indicate analog input signals,
Digital Contact output terminals, communication
10 Mbps
terminals and Ethernet N/W terminal
TCP/IP
Insulation Resistance: 20MΩ or more at 500 V DC
MODNET
Signal Isolation Specifications
Sr.No Signals
Flash Memory (32
1 Power Input
MB)
Periodic and Event
2 Analog Inputs
25 MB
7 MB
DD/MM/YY –
HH:MM:SS
3 RS-485
1 Second minimum
Communication
4 Ethernet
1 second
Communication
1(USB 2.0)
5 Relay contacts
For retrieving logged
data only
6 Digital Output
Upto 32 GB
 FAT16
 FAT32
.xls (only)
 Full Data Fetch
 Fetch Data by time
2-digits, 7-segment, Green , 0.56"
character height
4-digits, 7-segment, Red, 0.56''
character height
6-digits, 16-segment Alphanumeric,
Orange LEDs, 0.3" character height
24-Red LEDs for Alarm, 24-Orange
LEDs Control Output, 8-Green LEDs for
Relay, 1-Red LED for Manual mode, 1-
Green for Run mode,1-Red for Fault,
2-Green(Rx) & 2-Red(Tx) for
Communication
-10 to 55°C
30% to 95% RH
(Non-Condensing)
< 100ppm
1.25 KG
<15 mins after power
on
IP54 (From Front)
85-265VAC-50/60Hz /
100-300VDC or 18-36VDC
Max. 16 VA (85-265 VAC)
and Max. 8 VA (18-36
VDC)
Signal Isolation
Isolated from other ip/op
terminals and internal circuit
Not isolated from other analog
i/p terminals & the internal
circuit. But isolated from other
ip/op terminals.
Isolated from other ip/op
terminals and internal circuit
Isolated from other ip/op
terminals and internal circuit
Isolated between contact o/p
terminals & from other ip/op
terminals and internal circuit
Isolated from other ip/op
terminals and internal circuit
Page 1 of 2